Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.11
RM2170E _55 Steering _057027 STEERING COLUMN _0278046 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Hybrid Control System cannot Start)  


DESCRIPTION

The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if a hybrid control system operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the hybrid control system cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Hybrid control system cannot start)
Entry&Start
·

All items (See page (Click here))


-

WIRING DIAGRAM

C317803E11
5.406,3.292 5.719,3.479 0.313,0.188 10 false IGE 5.396,2.771 5.708,2.958 0.313,0.188 10 false LIN 5.406,3.802 5.813,3.99 0.406,0.188 10 false GND 5.188,2.604 5.354,2.792 0.167,0.188 10 false 5 5.198,3.198 5.365,3.385 0.167,0.188 10 false 3 5.198,3.688 5.365,3.875 0.167,0.188 10 false 1 4.885,4.198 5.177,4.385 0.292,0.188 10 false G50 4.885,4.344 6.719,4.698 1.833,0.354 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 2.938,2.76 3.292,2.948 0.354,0.188 10 false G79 1.792,4.229 3.385,4.635 1.594,0.406 10 false Certification ECU (Smart Key ECU Assembly) 4.635,5.854 6.302,6.052 1.667,0.198 10 false : LIN Communication Line 4.635,6.198 6.417,6.396 1.781,0.198 10 false : CAN Communication Line 0.135,1.646 1.615,2.052 1.479,0.406 10 false ID Code Box (Immobiliser Code ECU) 2.635,2.76 2.906,2.948 0.271,0.188 10 false LIN 2.51,3.302 2.917,3.49 0.406,0.188 10 false SLR+ 2.76,3.802 3.167,3.99 0.406,0.188 10 false P 2.698,5.49 3.104,5.677 0.406,0.188 10 false P2 2.969,5.375 3.375,5.563 0.406,0.188 10 false 2 2.99,2.573 3.188,2.76 0.198,0.188 10 false 17 2.948,3.302 3.302,3.49 0.354,0.188 10 false G79 3,3.115 3.198,3.302 0.198,0.188 10 false 29 2.948,3.781 3.302,3.969 0.354,0.188 10 false G79 3,3.594 3.198,3.781 0.198,0.188 10 false 25 0.208,4.208 1.406,4.75 1.198,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 0.135,1.458 0.49,1.646 0.354,0.188 10 false G49 0.917,1.063 1.25,1.25 0.333,0.188 10 false LIN1 1.281,0.896 1.479,1.083 0.198,0.188 10 false 2 5.406,0.333 5.719,0.521 0.313,0.188 10 false B 5.198,0.229 5.365,0.417 0.167,0.188 10 false 7 4.167,0.51 5.083,0.698 0.917,0.188 10 false STRG LOCK 2.031,0.344 3.396,0.531 1.365,0.188 10 false from Auxiliary Battery 1.771,3.833 2.125,4.021 0.354,0.188 10 false G77 1.833,3.646 2.031,3.833 0.198,0.188 10 false 11 2.104,3.833 2.51,4.021 0.406,0.188 10 false E 1.635,5.823 2.042,6.01 0.406,0.188 10 false G25 1.635,5.99 3.448,6.427 1.813,0.438 10 false Shift Lock Control ECU (Lower Shift Lever Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.


·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, confirm that the problem does not occur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the steering lock ECU (steering lock actuator assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

If the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the hybrid control system. If the steering is locked for any reason, open and close a door with the power switch off, and then unlock the steering by pressing the power switch. This prevents the hybrid control system from starting while the steering is locked.



PROCEDURE

1.CHECK DTC (ALL)

OK

2.CHECK POWER SWITCH (SWITCH CONDITION)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK POWER SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P, check that pressing the power switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → on (ACC) → on (IG) → off





OK

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK REQUEST RECEIVE)

NG

GO TO SMART ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock request is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK: Within 10 seconds of turning power switch on (IG) or on (ACC) or starting hybrid control system
NG: Except above
·

If the unlock signal has not been received, the hybrid control system cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the power switch on (ACC) or on (IG) or starting the hybrid control system, the Data List item changes to "OK".




OK

4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

9.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

U183493E01
0.31,0.29 0.496,0.451 0.186,0.161 10 *a 4.799,0.934 5.094,1.090 0.295,0.156 10 G79 2.181,0.932 2.476,1.088 0.295,0.156 10 G77 4.851,1.882 4.85,2.329 false 4.815,2.354 4.928,2.510 0.113,0.156 10 P 2.72,1.863 2.717,2.344 false 2.672,2.375 3.000,2.531 0.328,0.156 10 E

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

Standard Voltage:
Tester Connection Condition Specified Condition
G79-25 (P) - G77-11 (E) Shift lever in P 9 V or higher
G79-25 (P) - G77-11 (E) Shift lever not in P 1.5 V or less




OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

7.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Disconnect the G50 steering lock ECU connector.


b.
U159322E03
2.219,2.438 2.5,1.615 false 1.063,2.958 1.229,2.469 false 0.396,0.24 0.625,0.417 0.229,0.177 10 false *a 2.469,1.438 2.625,1.625 0.156,0.188 10 false B 0.844,2.979 1.229,3.167 0.385,0.188 10 false GND 0.396,0.948 0.708,1.094 0.313,0.146 10 false G50

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G50-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the connection which leads to ground.


Standard Voltage:
Tester Connection Condition Specified Condition
G50-7 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))



OK

6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the G50 steering lock ECU connector.


b.
U159426E03
2.292,1.073 2.771,1.677 false 1.521,2.917 2.885,2.698 2.885,2.698 2.719,2.969 false 2.135,4.198 2.135,4.385 false 1.885,1.083 0.844,1.688 false 0.375,0.115 0.552,0.302 0.177,0.188 10 false *a 2.917,2.583 3.094,2.771 0.177,0.188 10 false *b 2.063,4.406 2.24,4.594 0.177,0.188 10 false *c 0.635,1.688 0.917,1.854 0.281,0.167 10 false IGE 2.615,1.688 2.969,1.854 0.354,0.167 10 false GND 2.969,4.063 3.344,4.229 0.375,0.167 10 false GND 0.26,0.813 0.573,0.958 0.313,0.146 10 false G50

Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection G50-3 (IGE) - G50-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


HINT:
·

When taking measurements while the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.

-

To lock the steering, turn the power switch off with the shift lever in P, and then open a door.





OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G25 shift lock control ECU (lower shift lever assembly) connector.


b.

Disconnect the G79 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-2 (P2) - G79-25 (P) Always Below 1 Ω
G25-2 (P2) or G79-25 (P) - Body ground Always 10 kΩ higher




OK

8.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)
a.

Reconnect the G25 shift lock control ECU (lower shift lever assembly) connector.


b.
U159580E01
0.171,0.174 0.399,0.349 0.227,0.176 10 *a 1.552,0.315 1.860,0.457 0.309,0.142 10 G25 1.832,1.203 2.439,0.807 false 2.469,0.718 2.692,0.902 0.223,0.184 10 P2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-2 (P2) - Body ground Shift lever in P 9 V or higher
G25-2 (P2) - Body ground Shift lever not in P 1.5 V or less


Text in Illustration
*a Component with harness connected
(Shift Lock Control ECU (Lower Shift Lever Assembly))



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

9.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)

OK

10.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)

NG

12.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
10.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)

OK

11.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
11.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

OK

END

NG

REPLACE STEERING LOCK ACTUATOR ASSEMBLY