Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the power management control ECU receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.

·

When the smart entry and start system cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.


HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B309716E04
2.926,1.301 3.300,1.494 0.373,0.193 10 IG1D 3.397,1.129 3.534,1.294 0.137,0.165 10 2 2.837,4.985 3.276,5.178 0.439,0.193 10 ACCD 3.393,4.799 3.523,4.965 0.130,0.165 10 1 4.952,1.614 5.647,1.807 0.695,0.193 10 IG1 NO. 1 4.952,2.833 5.647,3.026 0.695,0.193 10 IG1 NO. 2 4.952,4.065 5.647,4.258 0.695,0.193 10 IG1 NO. 3 2.27,7.985 3.673,8.420 1.403,0.436 10 Power Management Control ECU 3.886,5.712 6.585,5.877 2.699,0.165 10 Instrument Panel Junction Block Assembly 5.058,7.596 5.341,7.789 0.283,0.193 10 IG2 3.311,4.982 3.633,5.147 0.322,0.165 10 G58 3.311,1.301 3.633,1.466 0.322,0.165 10 G58 3.882,0.884 4.118,1.049 0.235,0.165 10 3E 3.857,0.702 4.089,0.867 0.232,0.165 10 1*1 4.205,0.884 4.440,1.049 0.235,0.165 10 3F 4.179,0.702 4.411,0.867 0.232,0.165 10 1*2 3.874,1.302 4.113,1.467 0.239,0.165 10 3A 3.884,1.122 4.125,1.287 0.242,0.165 10 29 6.488,0.894 6.711,1.059 0.223,0.165 10 3A 6.505,0.726 6.725,0.891 0.220,0.165 10 54 5.954,2.248 6.456,2.441 0.502,0.193 10 WIPER 5.916,1.023 6.481,1.366 0.565,0.343 10 ECU-IG NO. 1 6.552,1.936 6.793,2.102 0.242,0.165 10 9 6.506,4.388 6.748,4.553 0.242,0.165 10 13 6.022,4.686 6.399,4.902 0.377,0.216 10 ACC 6.533,4.803 6.775,4.968 0.242,0.165 10 8 4.511,6.688 4.752,6.853 0.242,0.165 10 4 4.68,7.967 6.229,8.284 1.549,0.317 10 No. 1 Integration Relay 3.873,4.982 4.126,5.147 0.253,0.165 10 3B 3.887,4.814 4.128,4.979 0.242,0.165 10 37 6.495,2.114 6.718,2.279 0.223,0.165 10 3A 6.49,4.569 6.783,4.734 0.293,0.165 10 3B 6.49,4.984 6.713,5.149 0.223,0.165 10 3B 4.468,6.864 4.691,7.029 0.223,0.165 10 2D 0.193,0.624 1.079,1.039 0.886,0.416 10 from Auxiliary Battery 1.395,0.774 1.725,0.964 0.329,0.191 10 AM2 2.491,0.624 2.931,0.773 0.441,0.149 10 AM21 2.227,0.44 2.338,0.585 0.111,0.145 10 7 2.137,0.624 2.418,0.814 0.281,0.191 10 G58 2.491,1.03 2.931,1.179 0.441,0.149 10 AM22 2.227,0.848 2.338,0.993 0.111,0.145 10 1 2.137,1.03 2.420,1.221 0.284,0.191 10 G57 2.498,1.683 2.939,1.832 0.441,0.149 10 E01 2.234,1.497 2.345,1.643 0.111,0.145 10 5 2.137,1.683 2.420,1.874 0.284,0.191 10 G57 2.498,2.083 2.939,2.232 0.441,0.149 10 E02 2.241,1.896 2.352,2.042 0.111,0.145 10 5 2.137,2.083 2.420,2.273 0.284,0.191 10 G58 2.498,2.472 2.939,2.621 0.441,0.149 10 E1 2.22,2.286 2.331,2.431 0.111,0.145 10 6 2.137,2.472 2.420,2.663 0.284,0.191 10 G57 0.644,4.542 1.649,4.712 1.006,0.169 10 Power Switch 0.304,4.542 0.615,4.708 0.311,0.165 10 G48 1.004,3.725 1.444,3.874 0.441,0.149 10 SS1 1.018,4.166 1.458,4.315 0.441,0.149 10 SS2 1.367,3.616 1.478,3.762 0.111,0.145 10 5 1.366,4.06 1.476,4.205 0.111,0.145 10 1 2.498,3.716 2.939,3.865 0.441,0.149 10 SSW1 2.498,4.169 2.939,4.318 0.441,0.149 10 SSW2 2.243,3.534 2.354,3.679 0.111,0.145 10 7 2.137,3.72 2.433,3.911 0.297,0.191 10 G57 2.197,3.977 2.387,4.123 0.191,0.145 10 17 2.137,4.162 2.433,4.352 0.297,0.191 10 G58 2.203,5.193 2.417,5.358 0.214,0.165 10 23 2.497,5.378 2.878,5.543 0.380,0.165 10 STP 2.153,5.373 2.475,5.538 0.322,0.165 10 A39 1.186,6.681 2.088,7.154 0.902,0.473 10 from Auxiliary Battery 0.347,5.96 0.658,6.125 0.311,0.165 10 A65 0.347,6.116 2.083,6.281 1.736,0.165 10 Stop Light Switch Assembly 0.447,6.838 0.903,7.003 0.456,0.165 10 STOP 0.251,8.424 0.985,8.589 0.734,0.165 10 *2: for RHD 0.251,8.121 0.962,8.287 0.711,0.165 10 *1: for LHD 1.622,5.286 1.759,5.451 0.137,0.165 10 4 1.622,5.702 1.759,5.867 0.137,0.165 10 3 0.732,5.702 0.870,5.867 0.137,0.165 10 1 1.439,5.364 1.549,5.529 0.110,0.165 10 L 0.906,5.796 1.044,5.961 0.137,0.165 10 B 1.221,5.8 1.576,5.993 0.355,0.193 10 GND 5.116,5.293 5.493,5.509 0.377,0.216 10 ACC 2.912,7.288 3.260,7.481 0.347,0.193 10 IG2D 3.423,7.11 3.665,7.275 0.242,0.165 10 2 3.333,7.286 3.605,7.451 0.272,0.165 10 A39 4.511,7.11 4.752,7.276 0.242,0.165 10 3 4.468,7.286 4.691,7.452 0.223,0.165 10 2D 6.145,7.108 6.387,7.273 0.242,0.165 10 2 6.103,7.284 6.326,7.449 0.223,0.165 10 2D 6.145,6.696 6.387,6.861 0.242,0.165 10 1 6.103,6.872 6.326,7.037 0.223,0.165 10 2E 5.667,7.001 5.950,7.194 0.283,0.193 10 IG2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the electrical key transmitter sub-assembly, refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>PRECAUTION).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

OK:

Wireless door lock function operates.




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO OTHER DIAGNOSIS PROCEDURE (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK SMART ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SMART ENTRY AND START SYSTEM
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


b.
B296539E01
0.708,0.284 0.887,0.472 0.179,0.188 10 *1 2.733,1.657 2.912,1.846 0.179,0.188 10 *2 1.44,0.615 1.228,0.37 1.228,0.37 0.891,0.37 false 2.183,1.537 2.26,1.746 2.26,1.746 2.71,1.746 false

With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


Result:
Result Proceed to
The power source mode does not change. A
The power source mode changes. B


Text in Illustration
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly



A

5.READ VALUE USING INTELLIGENT TESTER

B

8.READ VALUE USING INTELLIGENT TESTER
5.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Specified Condition
Stop Light Switch1 State of brake pedal/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.



OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.




OK

6.READ VALUE USING INTELLIGENT TESTER

NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
6.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).


b.

With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.

OK:

IG2 ON is displayed in the Data List.


HINT:

If the smart entry and start system function has been canceled on the customization menu, ACC ON is displayed in the Data List.




OK

7.CHECK POWER MANAGEMENT CONTROL ECU

NG

14.CHECK FOR DTC
7.CHECK POWER MANAGEMENT CONTROL ECU
a.
U183358E02
1.594,1.125 1.177,1.813 false 2.833,1.125 2.938,1.833 false 2.76,1.125 2.25,1.833 false 0.073,0.01 0.396,0.198 0.323,0.188 10 false *a 1.292,0.427 1.615,0.615 0.323,0.188 10 false A39 2.458,0.438 2.781,0.625 0.323,0.188 10 false G58 2.729,1.844 3.208,2.031 0.479,0.188 10 false ACCD 1,1.833 1.479,2.021 0.479,0.188 10 false IG2D 2.073,1.844 2.552,2.031 0.479,0.188 10 false IG1D

Read the Data List according to the display on the intelligent tester.

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


b.

Measure the voltage according to the value(s) in the table below.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).


c.

Measure the voltage while checking the Data List on the intelligent tester.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-2 (IG1D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
A39-2 (IG2D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
G58-1 (ACCD) - Body ground Power switch off 1 V or less
Power switch on (IG) 8.5 V or higher
Power switch on (ACC) 8.5 V or higher




OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

8.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status/ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status/ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.



OK:

ON (Power switch is pressed) and OFF (Power switch is not pressed) appear on the screen.


Result:
Result Proceed to
NG A
OK B




A

9.INSPECT POWER SWITCH

B

9.INSPECT POWER SWITCH
a.


OK

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - POWER SWITCH)

NG

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - POWER SWITCH)
a.

Disconnect the G57 and G58 power management control ECU connectors.


b.

Disconnect the G48 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-7 (SSW1) - G48-5 (SS1) Always Below 1 Ω
G58-17 (SSW2) - G48-1 (SS2) Always Below 1 Ω
G57-7 (SSW1) or G48-5 (SS1) - Body ground Always 10 kΩ or higher
G58-17 (SSW2) or G48-1 (SS2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.
U183738E02
1.333,1.292 1.042,1.75 false 1.719,1.292 2,1.771 false 0.219,0.125 0.573,0.417 0.354,0.292 10 false *a 1.594,0.208 1.948,0.5 0.354,0.292 10 false A65 0.958,1.75 1.125,1.938 0.167,0.188 10 false B 1.854,1.771 2.219,1.958 0.365,0.188 10 false GND

Disconnect the A65 stop light switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-1 (B) - A65-3 (GND) Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A65-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

12.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
U183742E02
1.49,1.292 1.198,1.74 false 1.74,1.302 2.167,1.729 false 0.25,0.125 0.448,0.302 0.198,0.177 10 false *a 1.615,0.24 1.979,0.417 0.365,0.177 10 false A65 1.104,1.729 1.198,1.906 0.094,0.177 10 false L 2.125,1.75 2.552,1.927 0.427,0.177 10 false GND

Reconnect the A65 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-4 (L) - A65-3 (GND) Power switch off, brake pedal not depressed Below 1 V
A65-4 (L) - A65-3 (GND) Power switch off, brake pedal depressed 11 to 14 V


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)



OK

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK FOR DTC
a.

Enter the following menus:

for Entry&Start: Body / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Result:
Result Proceed to
The following DTCs are not output:
·

B2785

·

B2287

·

B2784

·

B278A


A
DTC B2785 is not output but DTC B2287 is output. B
DTCs other than B2287 are output. C




A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

GO TO DTC CHART