Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278145 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

(See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>PRECAUTION)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55405B 4.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B301680E02
2.323,1.677 2.24,1.854 false 2.125,1.896 2.354,2.083 0.229,0.188 10 true *1

Apply protective tape to the area shown in the illustration.

Text in Illustration
*1 Protective Tape


b.
B301681

Using a moulding remover, disengage the 8 clips and claw.

NOTICE:

Do not use a moulding remover to an area other than that shown in the illustration. Using a moulding remover in an area other than that shown in the illustration may result in deformation or damage to related parts.



c.

Disconnect the connector and remove the center instrument cluster finish panel sub-assembly.


Hide 55660 5.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)

a.
B301683

Disengage the 3 clips and remove the No. 2 instrument panel register assembly.


Hide 55650 6.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for RHD)

a.
B297457

Disengage the 3 clips and remove the No. 1 instrument panel register assembly.


Hide 55474B 7.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B301684E02
2.385,1.427 2.688,0.979 true 2.74,0.885 2.969,1.094 0.229,0.208 10 true *1

Apply protective tape to the area shown in the illustration.

Text in Illustration
*1 Protective Tape


b.
B301685

Using a moulding remover, disengage the 12 clips and 10 guides to remove the instrument cluster finish panel garnish.


Hide 55670A 8.REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B301687

Disengage the claw and 4 clips to remove the center instrument panel register assembly.


Hide 55404D 9.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
B301688

Using a clip remover, remove the 2 clips.


b.
B301689

Disengage the 4 claws and 9 guides and remove the instrument cluster finish panel sub-assembly.


Hide 83100 10.REMOVE COMBINATION METER ASSEMBLY

Hide 62312B 11.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect the front door opening trim weatherstrip LH.


Hide 62212 12.REMOVE FRONT PILLAR GARNISH LH

Hide 62311B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.

Disconnect the front door opening trim weatherstrip RH.


Hide 62211 14.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 16.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

a.

Remove the bolt <A>.

B301690E02
3.125,1.427 3.313,1.458 true 6.385,2.073 6.396,2.323 false 3.333,1.385 3.531,1.563 0.198,0.177 10 true *2 6.344,2.333 6.5,2.479 0.156,0.146 10 false *1

Text in Illustration
*1 Bolt <A> *2 Screw <C>


b.

Remove the screw <C>.


c.

Using a clip remover, remove the 2 clips.


d.

Pull the upper instrument panel assembly in the direction indicated by the arrow (1) to disengage the 7 clips.

B301692E02
3.885,2.063 4.094,2.25 0.208,0.188 10 true (1) 4.875,1.438 5.104,1.646 0.229,0.208 10 true (2)


e.

Pull the upper instrument panel assembly in the direction indicated by the arrow (2) to disengage the 5 guides and remove the upper instrument panel assembly.