Use the same procedure for the RH side and LH side.
The procedure described below is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2. REPAIR INSTRUCTION
75924
3.INSTALL NO. 2 BLACK OUT TAPE
69204A
4.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
Engage the door handle nut and claw.
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.
69242G
5.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
Engage the 2 claws and install the rear door outside handle rear pad.
69241G
6.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
Engage the 3 claws to install the rear door outside handle front pad.
69240
7.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.
If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.
Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.
69227L
8.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claw to install the rear door outside handle cover.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.
69780B
9.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
Install the rear door inside locking cable assembly as shown in the illustration.
Engage the 3 claws as shown in the illustration.
69740D
10.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Install the rear door lock remote control cable assembly as shown in the illustration.
Engage the claw as shown in the illustration.
69340
11.INSTALL REAR DOOR LOCK ASSEMBLY
When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.
Apply MP grease to the sliding parts of the rear door lock assembly.
When reusing the rear door lock assembly:
Install a new door lock wiring harness seal to the rear door lock assembly.
Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
| *1 | Release Plate |
Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.
Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.
Connect the connector.
Install the rear door lock child protection cover.
68124B
12.INSTALL REAR DOOR QUARTER WINDOW GLASS
Install the rear door quarter window weatherstrip to the rear door quarter window glass.
Install the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
68230C
13.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
85720E
14.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.
Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
69830A
15.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Install the temporary bolt to the rear door window regulator assembly.
Temporarily install the rear door window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly in the order shown in the illustration.
Connect the connector.
69975A
16.INSTALL REAR DOOR GLASS CHANNEL FILLER
Apply soapy water to a new rear door glass channel filler.
Install the new rear door glass channel filler as shown in the illustration.
| *a | Front Side |
| *b | Rear Side |
| *c | Edge of curved surface |
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
| B | 5.0 mm (0.197 in.) |
69906B
17.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
Apply soapy water to a rear door glass channel.
Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel sub-assembly.
| *a | Front Side |
| *b | Rear Side |
| *c | Edge of curved surface |
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
| B | 5.0 mm (0.197 in.) |
Be careful not to damage the glass or glass channel.
Make sure the position of the rear door glass channel filler does not change.
68104
18.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Insert the rear door glass as indicated by the arrows in the order shown in the illustration.
Do not damage the rear door glass.
Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.
67408E
19.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Temporary install the rear door window division bar sub-assembly with the 2 bolts.
Do not damage the rear door glass.
Install the rear door window division bar sub-assembly with the 2 bolts and screw.
68152C
20.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
67872
21.INSTALL REAR DOOR WEATHERSTRIP
Clean the rear door panel sub-assembly.
Engage the 30 clips to install a new front door weatherstrip.
| *1 | Double-sided tape |
68630
22.INSTALL REAR DOOR CHECK ASSEMBLY
Apply MP grease to the sliding areas of the rear door check assembly.
Apply adhesive to the threads of the bolt (A).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the rear door check assembly with the 3 bolts.
67842E
23.INSTALL REAR DOOR SERVICE HOLE COVER
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *a | Reference Point |
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
86160B
24.INSTALL REAR SPEAKER ASSEMBLY
68174A
25.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
Engage the 5 claws to install the rear door glass inner weatherstrip as shown in the illustration.
69206C
26.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 4 guides to install the rear door inside handle sub-assembly.
67604
27.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
Engage the 7 clips.
Engage the clip.
Install the rear door trim board sub-assembly with the 3 screws.
Engage the claw and close the cover.
28.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Connect the connector.
Engage the 3 guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
67674A
29.INSTALL REAR DOOR FRAME GARNISH
Engage the guide.
Engage the 2 clips and 3 claws to install the rear door frame garnish.
30.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
58165F
31.INSTALL FRONT FLOOR COVER RH
32.INSPECT POWER WINDOW OPERATION