Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) J

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the start request signal output from the certification ECU (smart key ECU assembly) is input to the ECM, and the NE signal generated by the crank position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump with filter assembly operates.

While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A410575E02
4.688,0.552 4.844,0.75 0.156,0.198 10 false 9 4.906,0.719 5.427,0.979 0.521,0.26 10 false IG2D 4.667,1.229 5.125,1.542 0.458,0.313 10 false G77 4.625,1.438 6.427,1.854 1.802,0.417 10 false Certification ECU (Smart Key ECU Assembly) 3.813,2.198 3.969,2.396 0.156,0.198 10 false 3 3.917,2.438 4.229,2.635 0.313,0.198 10 false 2D 1.156,3.198 1.563,3.51 0.406,0.313 10 false P/I 2.031,2.99 2.344,3.188 0.313,0.198 10 false 2E 2.073,2.802 2.229,3 0.156,0.198 10 false 1 2.073,3.167 2.229,3.365 0.156,0.198 10 false 2 2.063,3.323 2.375,3.521 0.313,0.198 10 false 2D 2.802,3.156 3.167,3.448 0.365,0.292 10 false IG2 3.365,3.656 3.823,3.854 0.458,0.198 10 false IG2 4.625,2.99 4.938,3.188 0.313,0.198 10 false 2D 4.646,2.771 4.802,2.969 0.156,0.198 10 false 4 4.948,3.156 5.354,3.625 0.406,0.469 10 false IG2 NO. 2 2.042,4.646 2.354,4.844 0.313,0.198 10 false 2C 2.094,4.438 2.25,4.635 0.156,0.198 10 false 2 2.552,4.438 3.417,4.75 0.865,0.313 10 false EFI-MAIN 3.229,5 4.063,5.333 0.833,0.333 10 false EFI-MAIN 4.604,4.302 4.917,4.5 0.313,0.198 10 false 2C 4.646,4.094 4.802,4.292 0.156,0.198 10 false 4 4.604,4.667 4.917,4.865 0.313,0.198 10 false 2C 4.635,4.469 4.792,4.667 0.156,0.198 10 false 3 5.708,4.542 6.021,4.74 0.313,0.198 10 false 46 5.917,4.656 6.458,4.948 0.542,0.292 10 false MREL 2.031,5.719 2.344,5.917 0.313,0.198 10 false 2D 2.073,5.531 2.229,5.729 0.156,0.198 10 false 8 1.948,7.177 2.104,7.375 0.156,0.198 10 false 4 1.938,7.375 2.094,7.573 0.156,0.198 10 false B 1.948,7.906 2.104,8.104 0.156,0.198 10 false E 1.948,8.125 2.104,8.323 0.156,0.198 10 false 5 2.25,7.448 2.646,7.792 0.396,0.344 10 false M22 2.25,7.635 3.552,8.323 1.302,0.688 10 false Fuel Pump with Filter Assembly 3.292,6.479 4.01,6.802 0.719,0.323 10 false C/OPN 2.75,7.031 4.385,7.49 1.635,0.458 10 false No. 1 Integration Relay 4.604,5.74 4.917,5.938 0.313,0.198 10 false 2D 4.635,5.521 4.792,5.719 0.156,0.198 10 false 5 4.625,6.135 4.938,6.333 0.313,0.198 10 false 2D 4.635,5.948 4.792,6.146 0.156,0.198 10 false 6 4.594,6.688 4.906,6.885 0.313,0.198 10 false 2D 4.635,6.458 4.792,6.656 0.156,0.198 10 false 7 5.656,6.563 5.969,6.76 0.313,0.198 10 false 21 5.917,6.563 6.229,6.823 0.313,0.26 10 false FC 6.594,6.01 6.99,6.333 0.396,0.323 10 false Tr1 5.906,7.844 6.365,8.042 0.458,0.198 10 false A40 6.229,7.854 6.688,8.052 0.458,0.198 10 false ECM 0.573,6.167 1.104,6.49 0.531,0.323 10 false MAIN 0.708,7.677 1.26,8.094 0.552,0.417 10 false Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

Check whether the fuel pump with filter assembly operating sound occurs when performing the Active Test on the GTS.

Result
Result Proceed to
Fuel pump with filter assembly operating sound does not occur A
Fuel pump with filter assembly operating sound occurs B



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-7 - A40-21 (FC) Always Below 1 Ω
2D-7 or A40-21 (FC) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP WITH FILTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP WITH FILTER ASSEMBLY)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the fuel pump with filter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-8 - M22-4 (B) Always Below 1 Ω
2D-8 or M22-4 (B) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP WITH FILTER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP WITH FILTER ASSEMBLY - BODY GROUND)
a.

Disconnect the fuel pump with filter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-5 (E) - Body ground Always Below 1 Ω




OK

5.INSPECT FUEL PUMP WITH FILTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP WITH FILTER ASSEMBLY
a.

Inspect the fuel pump with filter assembly.

Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL PUMP(w/ Canister Pump Module)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump with filter assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

6.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)

NG

6.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)
a.

Inspect the No. 1 integration relay (C/OPN relay).

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 INTEGRATION RELAY)

NG