Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

Refer to DTC P0010.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0010

DTC No. DTC Detection Condition Trouble Area
P0011 Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


P0012 Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.


Example:

A DTC is stored when the following conditions "A" and "B" are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").

(b)

After the above condition is met, the camshaft timing oil control valve assembly is forcibly activated for 10 seconds (Condition "B").


DTC P0011 (Advanced Cam Timing) is subject to 1 trip detection logic.

DTC P0012 (Retarded Cam Timing) is subject to 2 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve assembly malfunction or the presence of foreign objects in the camshaft timing oil control valve assembly.


MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing oil control valve assembly
Camshaft timing gear assembly
Required Sensors/Components (Related) Crank position sensor
Cam position sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A217996E64
2.281,3.292 2.146,3.292 2.146,3.292 2.521,2.635 false 0.156,0.302 1.219,0.729 1.063,0.427 10 false Vehicle Speed 0.073,1.135 1.281,1.385 1.208,0.25 10 false 60 km/h or more 0.771,2.073 1.26,2.406 0.49,0.333 10 false Idling 0.271,2.333 1.135,2.802 0.865,0.469 10 false Power Switch on (IG) 1.385,2.354 1.833,2.552 0.448,0.198 10 false [A] 1.885,2.042 2.344,2.313 0.458,0.271 10 false [B] 4.146,2.021 4.646,2.323 0.5,0.302 10 false [D] 6.417,2.031 6.792,2.333 0.375,0.302 10 false [G] 2.448,1.604 2.99,1.938 0.542,0.333 10 false [C] 4.719,1.604 5.208,1.917 0.49,0.313 10 false [F] 3.719,2.74 4.448,3.219 0.729,0.479 10 false 30 seconds or more 2.323,3.219 3.667,3.552 1.344,0.333 10 false 10 seconds or more 1.594,2.729 2.552,3.083 0.958,0.354 10 false Warming up 6.719,3.177 7.094,3.479 0.375,0.302 10 false [H] 4.448,3.167 4.823,3.469 0.375,0.302 10 false [E] 4.667,2.729 5.396,3.208 0.729,0.479 10 false 10 seconds or more 6,2.708 6.729,3.188 0.729,0.479 10 false 30 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

HINT:
·

P0011 is output:

Clear the DTC not using the GTS.

·

P0012 is output:

Clear the DTC using the GTS.



4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

8.

Accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for 10 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


9.

Idle the engine for 30 seconds or more [D].

HINT:
·

P0011 is output:

With the shift lever in P.

·

P0012 is output:

With the shift lever in D.



10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0011 or P0012.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



15.

Accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for 10 seconds or more [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Idle the engine for 30 seconds or more (shift position in P) [G].

17.

Check the DTC judgment result again [H].

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0011 or P0012 is output A
DTC P0011 or P0012 and other DTCs are output B

HINT:

If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).


g.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls

HINT:
·

Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

If the result is not acceptable, cool the engine (engine coolant temperature is 50°C (122°F) or less) and perform the Active Test again.

·

Test not possible with the shift lever in P during charge control. Move the shift lever to N to perform test.

·

If the DTCs are stored after the Active Test, clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR





OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

4.CHECK VALVE TIMING
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

HINT:
·

P0011 is output:

Clear the DTC not using the GTS.

·

P0012 is output:

Clear the DTC using the GTS.




e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


l.

Read the pending DTCs.

Result
Result Proceed to
DTCs are not output A
DTC P0011 or P0012 is output B

HINT:

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING
4.CHECK VALVE TIMING
A380683E01
3.167,0.844 3.583,0.208 false 4.313,0.844 3.844,0.198 false 4.333,2.333 3.5,3.333 3.5,3.333 3.063,2.229 false 4.531,5.094 4.531,4.292 false 3.635,0.125 3.948,0.323 0.313,0.198 10 false *1 3.406,3.375 3.719,3.573 0.313,0.198 10 false *1 2.427,3.76 2.74,3.958 0.313,0.198 10 false *a 4.448,5.115 4.76,5.313 0.313,0.198 10 false *2

a.

Remove the cylinder head cover sub-assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.


Text in Illustration
*1 Timing Mark
*2 Groove
*a No. 1 Cylinder TDC/Compression



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

9.CHECK ENGINE MECHANICAL SYSTEM
5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

b.

Check that the oil control valve filter is not clogged.

OK:

Oil control valve filter is not clogged.




OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

HINT:
·

P0011 is output:

Clear the DTC not using the GTS.

·

P0012 is output:

Clear the DTC using the GTS.




e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


l.

Read the pending DTCs.

Result
Result Proceed to
DTCs are not output A
DTC P0011 or P0012 is output B



A

END

B

9.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.



OK

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

HINT:
·

P0011 is output:

Clear the DTC not using the GTS.

·

P0012 is output:

Clear the DTC using the GTS.




e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


l.

Read the pending DTCs.

Result
Result Proceed to
DTCs are not output A
DTC P0011 or P0012 is output B



A

B