Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0141  Oxygen Sensor Heater Circuit (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.

·

The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.


A269905E08
0.156,0.073 2.802,0.25 2.646,0.177 10 false Reference (System Diagram of Sensor 2): 0.104,1.104 0.958,1.521 0.854,0.417 10 false from Auxiliary Battery 3.25,1.99 4.74,2.167 1.49,0.177 10 false Heated Oxygen Sensor 3.396,1 3.698,1.24 0.302,0.24 10 false +B 3.792,0.792 4.229,0.969 0.438,0.177 10 false Heater 3.781,1.281 4.24,1.458 0.458,0.177 10 false Sensor 3.396,1.542 3.594,1.719 0.198,0.177 10 false E2 4.427,1.01 4.802,1.188 0.375,0.177 10 false HT1B 5,1.01 5.375,1.188 0.375,0.177 10 false HT1B 4.427,1.542 4.854,1.719 0.427,0.177 10 false OX1B 5,1.542 5.427,1.719 0.427,0.177 10 false OX1B 5,2.094 5.385,2.271 0.385,0.177 10 false EX1B 5.656,3.26 5.979,3.438 0.323,0.177 10 false ECM 1.76,2.302 2.563,2.667 0.802,0.365 10 false EFI-MAIN 1.094,1.281 1.771,1.615 0.677,0.333 10 false EFI-MAIN 4.99,2.552 5.625,2.729 0.635,0.177 10 false MREL


DTC No. DTC Detection Condition Trouble Area
P0037 Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


P0038 Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


P0141 The cumulative heater resistance correction value exceeds the threshold (2 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


P102D Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



Heated Oxygen Sensor Heater Performance (P0141):

After the accumulated heater on time exceeds 100 seconds, the ECM calculates the heater resistance using auxiliary battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P0141.



MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor heater
Frequency of Operation Continuous: P0037, P0038, P102D
Once per driving cycle: P0141

TYPICAL ENABLING CONDITIONS

P0037
Time after heater on 10 seconds or more

P0038
Time after heater on 10 seconds or more

P0141
Accumulated heater on time 100 seconds or more

P102D
Time after heater on 10 seconds or more

CONFIRMATION DRIVING PATTERN

A409294E02
0.75,1.021 1.625,1.333 0.875,0.313 10 false 2500 rpm 1.021,1.75 1.615,2.031 0.594,0.281 10 false Idling 0.094,2.063 1.74,2.417 1.646,0.354 10 false Power Switch on (IG) 1.917,2.177 2.25,2.469 0.333,0.292 10 false [A] 2.802,1.625 3.156,1.927 0.354,0.302 10 false [B] 2.323,2.563 3.51,2.917 1.188,0.354 10 false 5 minutes or more 3.875,2.594 4.563,2.885 0.688,0.292 10 false 1 minute 4.042,0.885 4.427,1.177 0.385,0.292 10 false [C] 5.375,1.656 5.688,1.979 0.313,0.323 10 false [D] 4.854,2.594 6.104,2.958 1.25,0.365 10 false 5 minutes or more 5.979,3.042 6.333,3.365 0.354,0.323 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine and idle it for 5 minutes or more [B].

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 2500 rpm for 1 minute [C].

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform steps [C] and [D] after charging control has completed.


9.

Idle the engine for 5 minutes or more [D].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0037, P0038, P0141 or P102D.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A275601E11
2.74,0.604 2.969,0.781 0.229,0.177 10 false 2C 0.823,0.74 1.479,0.938 0.656,0.198 10 false EFI-MAIN 4.615,1.24 4.771,1.417 0.156,0.177 10 false 3 1.229,5.969 2.479,6.302 1.25,0.333 10 false Auxiliary Battery 0.521,0.604 0.729,0.781 0.208,0.177 10 false 2E 0.573,0.406 0.729,0.583 0.156,0.177 10 false 1 2.792,0.406 2.948,0.583 0.156,0.177 10 false 4 3.365,1.573 3.656,1.75 0.292,0.177 10 false C16 5.396,0.594 5.677,0.771 0.281,0.177 10 false C10 5.396,2.063 5.729,2.24 0.333,0.177 10 false C10 5.396,1.375 5.677,1.552 0.281,0.177 10 false C10 5.406,3.073 5.76,3.385 0.354,0.313 10 false A40 5.469,2.885 5.635,3.063 0.167,0.177 10 false 46 5.458,0.427 5.708,0.604 0.25,0.177 10 false 22 5.427,1.198 5.677,1.375 0.25,0.177 10 false 103 5.417,1.875 5.667,2.052 0.25,0.177 10 false 135 4.177,0.469 4.552,0.646 0.375,0.177 10 false HT1B 3.771,1.229 4.094,1.406 0.323,0.177 10 false E2 4.167,1.229 4.656,1.406 0.49,0.177 10 false OX1B 5.052,2.438 5.167,2.615 0.115,0.177 10 false * 3.365,1.729 4.865,1.906 1.5,0.177 10 false Heated Oxygen Sensor 5.729,0.49 6.104,0.667 0.375,0.177 10 false HT1B 5.729,1.938 6.198,2.115 0.469,0.177 10 false EX1B 5.729,1.26 6.177,1.438 0.448,0.177 10 false OX1B 4.615,0.469 4.771,0.646 0.156,0.177 10 false 1 0.531,2.115 2.01,2.354 1.479,0.24 10 false No. 1 Integration Relay 6.167,4.854 6.531,5.031 0.365,0.177 10 false ECM 0.323,3.646 0.771,3.875 0.448,0.229 10 false P/I 1.594,1.198 2.365,1.5 0.771,0.302 10 false EFI-MAIN 3.521,3.729 4.354,3.917 0.833,0.188 10 false *: Shielded 3.604,0.469 3.76,0.646 0.156,0.177 10 false 2 3.615,1.24 3.771,1.417 0.156,0.177 10 false 4 3.781,0.469 4.021,0.646 0.24,0.177 10 false +B 5.75,3.052 6.177,3.229 0.427,0.177 10 false MREL 1.042,5.063 1.646,5.313 0.604,0.25 10 false MAIN 2.052,1.927 2.281,2.104 0.229,0.177 10 false 2C 2.146,1.729 2.302,1.906 0.156,0.177 10 false 2 2.448,1.927 2.677,2.104 0.229,0.177 10 false 2C 2.552,1.729 2.708,1.906 0.156,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2].

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.
U158895E02
2.344,2.01 1.875,2.219 false 2.406,1.927 2.677,2.125 0.271,0.198 10 false +B 0.208,0.156 0.427,0.375 0.219,0.219 10 false *a 0.594,2.198 1.01,2.49 0.417,0.292 10 false C16

Disconnect the heated oxygen sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C16-2 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (HT1B) - C10-22 (HT1B) Always Below 1 Ω
C16-1 (HT1B) or C10-22 (HT1B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the pending DTCs.


Result
Result Proceed to
DTCs are not output A
DTC P0037, P0038, P0141 or P102D is output B


A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

HINT:

Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-2 (+B) - 2C-4 Always Below 1 Ω
C16-2 (+B) or 2C-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR