When the engine is cranked, the start request signal output from the hybrid vehicle control ECU is input to the ECM, and the NE signal generated by the crank position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump with filter assembly operates.
While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether the fuel pump with filter assembly operating sound occurs when performing the Active Test on the tester.
| Result | Proceed to |
|---|---|
| Fuel pump with filter assembly operating sound does not occur | A |
| Fuel pump with filter assembly operating sound occurs | B |
A
B
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2D-7 - A40-21 (FC) | Always | Below 1 Ω |
| 2D-7 or A40-21 (FC) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Disconnect the fuel pump with filter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2D-8 - M22-4 (B) | Always | Below 1 Ω |
| 2D-8 or M22-4 (B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the fuel pump with filter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M22-5 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Inspect the fuel pump with filter assembly (See page Engine / Hybrid System>1NZ-FXE FUEL>FUEL PUMP(w/o Canister Pump Module)>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel pump with filter assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).
OK
NG
Inspect the No. 1 integration relay (C/OPN relay) (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the result when the power switch on (IG) and the engine starts.
| Condition | Starter Signal |
|---|---|
| Power switch on (IG) | Close (OFF) |
| Engine started | Open (ON) |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Read the values displayed on the tester while cranking.
Values are displayed continuously.
OK
NG
(See pageEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P0335)