Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A78-121  Drive Motor "A" Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

If an overvoltage occurs in the motor inverter or generator inverter, the MG ECU detects it and transmits this information to the power management control ECU.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A78 121 Motor inverter overvoltage signal detection (overvoltage due to system malfunction)
·

Hybrid battery junction block assembly

·

Inverter with converter assembly

·

Service plug grip (EV battery fuse)

·

Frame wire

·

Hybrid vehicle generator assembly

·

Hybrid vehicle motor assembly

·

Generator cable

·

Motor cable

·

Power management control ECU

·

PCU fuse

·

Wire harness or connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A1A-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals of the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

With the vehicle engine stopped, the power switch on (READY) and park (P) selected, depress the accelerator pedal to start the engine.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A78-121 is set before any of the DTCs in the table below are set. A
Any of the DTCs including pending DTCs in the table 1 below are set before P0A78-121 is set. B
Any of the DTCs including pending DTCs in the table 2 below are set before P0A78-121 is set. C


Table 1
DTC No. Relevant Diagnosis
P0AC0-817 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P3004-131 High Voltage Power Resource

Table 2
DTC No. Relevant Diagnosis
P0A7F-123 Hybrid Battery Pack Deterioration
P0A80-123 Replace Hybrid Battery Pack
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AE9-123 Hybrid Battery Temperature Sensor "D" Range / Performance
P0AEA-123 Hybrid Battery Temperature Sensor "D" Circuit Low
P0AEB-123 Hybrid Battery Temperature Sensor "D" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B10-123 Hybrid Battery Pack Current Sensor "B" Circuit Low
P0B11-123 Hybrid Battery Pack Current Sensor "B" Circuit High
P0B13-123 Hybrid Battery Pack Current Sensor "A"/"B" Correlation
P0BC3-123 Hybrid Battery Temperature Sensor "E" Range / Performance
P0BC4-123 Hybrid Battery Temperature Sensor "E" Circuit Low
P0BC5-123 Hybrid Battery Temperature Sensor "E" Circuit High
P0C34-123 Hybrid Battery Temperature Sensor "F" Range / Performance
P0C35-123 Hybrid Battery Temperature Sensor "F" Circuit Low
P0C36-123 Hybrid Battery Temperature Sensor "F" Circuit High
P3011-123 Battery Block 1 Becomes Weak
P3012-123 Battery Block 2 Becomes Weak
P3013-123 Battery Block 3 Becomes Weak
P3014-123 Battery Block 4 Becomes Weak
P3015-123 Battery Block 5 Becomes Weak
P3016-123 Battery Block 6 Becomes Weak
P3017-123 Battery Block 7 Becomes Weak
P3018-123 Battery Block 8 Becomes Weak
P301A-123 Open in Hybrid Battery Cell Voltage Detection Circuit
P301B-123 Hybrid Battery Cell Voltage Detection Circuit Range/Performance
P3065-123 Hybrid Battery Temperature Sensor Range/Performance Stuck "A
P306A-123 Hybrid Battery Temperature Sensor Range / Performance Stuck "B"
P31AA-123 Hybrid Battery Cell High Voltage
P31AB-123 Hybrid Battery Cell Low Voltage
P31AC-123 Hybrid Battery Cell Extreme High Voltage
P31B3-123 Hybrid Battery Voltage High
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:
·

Refer to the freeze frame data to determine the order in which the DTCs were set.

·

P0A78-121 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

C

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A78-121 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs including pending DTCs in the table 1 below are also output. B
Any of the following DTCs in the table 2 below are also output. C


Table 1
DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72 (all INF codes)*1 Generator Phase V Current
P0A75 (all INF codes)*1 Generator Phase W Current
P0A78-113, 128, 266, 267, 279, 284, 286, 287, 306, 503, 504, 505, 506, 565, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
P0A7A-122, 130, 322, 324, 325, 344, 517, 518, 809, 810, 811 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A93-346 Inverter Cooling System Performance
P0A94-172, 442, 547, 548, 549, 553, 554, 555, 556, 557, 585, 587, 589, 590 DC/DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P0C76-523 Hybrid Battery System Discharge Time Too Long
P3000-388, 389, 603 HV Battery Malfunction
P3004-133, 803 High Voltage Power Resource
P314A-828 Inverter Coolant Pump Speed Signal

Table 2
DTC No. Relevant Diagnosis
P0A95-123 High Voltage Fuse
P31B4-123 Extreme Charging Current Caused by Hybrid Battery High Voltage
P31B5-123 Abnormal Current Caused by Continuous Current from Hybrid Battery

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A78-121 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

C

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

5.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK GENERATOR RESOLVER

OK

6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

24.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

7.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MOTOR RESOLVER

OK

8.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

NG

26.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
8.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

31.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)
11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

12.CHECK INVERTER WITH CONVERTER ASSEMBLY (HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

33.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
12.CHECK INVERTER WITH CONVERTER ASSEMBLY (HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A209686

Remove the inverter cover from the inverter with converter assembly.


c.
A215642E11
1.76,0.844 1.885,1 0.125,0.156 10 true A 1.625,1.292 1.75,1.448 0.125,0.156 10 true A 1.229,0.344 1.354,0.5 0.125,0.156 10 true B 0.75,0.906 0.875,1.063 0.125,0.156 10 true B

Check that the bolts for the frame wire are tightened to the specified torque, the frame wire is connected securely, and there are no contact problems.

Specified Condition:
Bolt A:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)

Bolt B:

T=9.2 N*m (94 kgf*cm, 81 in.*lbf)


NOTICE:
·

Make sure that the tightening torque of the bolt A is between 6.4 and 9.6 N*m (65 and 98 kgf*cm, 57 and 85 in.*lbf).

·

Make sure that the tightening torque of the bolt B is between 6.4 and 12 N*m (65 and 122 kgf*cm, 57 and 106 in.*lbf).




d.

Disconnect the frame wire from the inverter with converter assembly.


e.

Check for arc marks at the bolts and terminals for the frame wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



f.

Connect the frame wire to the inverter with converter assembly.


g.

Install the inverter cover.



A

13.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

13.CHECK SERVICE PLUG GRIP (CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


a.

Visually check the connection of the service plug grip to the HV battery. Remove the service plug grip and check for contamination.

OK:

Dirt or foreign matter has not entered the connection, and there is no evidence of contamination.




OK

14.INSPECT SERVICE PLUG GRIP

NG

14.INSPECT SERVICE PLUG GRIP
a.
A204559E01
0.125,0.098 0.318,0.263 0.193,0.165 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Service plug grip terminals Always Below 1 Ω


Text in Illustration
*1 Service plug grip



OK

15.CHECK FRAME WIRE

NG

15.CHECK FRAME WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
A252586E01
0.091,0.014 0.326,0.202 0.235,0.188 10 *a

Disconnect the frame wire from the hybrid battery junction block assembly.

Text in Illustration
*a Frame Wire Connection Condition
(Hybrid Battery Junction Block Assembly)


d.
A209686

Remove the inverter cover from the inverter with converter assembly.


e.
A253625

Disconnect the frame wire from the inverter with converter assembly.


f.
U190691E02
1.406,2.125 1.188,2.281 false 1.875,2.125 2.073,2.302 false 0.865,3.375 0.646,3.552 false 1.177,3.01 1.708,2.896 false 2.333,1.292 2.646,1.167 false 0.844,4.094 1.042,3.854 false 0.146,0.104 0.417,0.375 0.271,0.271 10 false *1 0.156,2.521 0.5,2.729 0.344,0.208 10 false *2 2.021,2.323 2.427,2.563 0.406,0.24 10 false CBI 1.042,2.292 1.531,2.531 0.49,0.24 10 false CEI 0.333,1.021 0.563,1.208 0.229,0.188 10 false T1 0.792,2.698 0.99,2.865 0.198,0.167 10 false T6 0.448,3.125 0.646,3.281 0.198,0.156 10 false T5 1.75,2.823 2.052,3.042 0.302,0.219 10 false CBI 0.396,3.531 0.719,3.719 0.323,0.188 10 false CEI 0.708,4.073 0.938,4.281 0.229,0.208 10 false *3 2.677,1.063 2.906,1.271 0.229,0.208 10 false *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CBI) - T1-2 (CBI) (Positive terminal) Power switch off Below 1 Ω
T5-1 (CEI) - T1-1 (CEI) (Negative terminal) Power switch off Below 1 Ω


Text in Illustration
*1 Frame Wire (Inverter with Converter Assembly Side)
*2 Frame Wire (Hybrid Battery Junction Block Assembly Side)
*3 Shield Ground


g.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
T6-1 (CBI) - Body ground and shield ground Power switch off 10 MΩ or higher
T5-1 (CEI) - Body ground and shield ground Power switch off 10 MΩor higher
T6-1 (CBI) - T5-1 (CEI) Power switch off 10 MΩ or higher



h.

Connect the frame wire to the hybrid battery junction block assembly.


i.

Connect the frame wire to the inverter with converter assembly.


j.

Install the inverter cover.


k.

Install the No. 2 hybrid battery shield sub-assembly.



OK

16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

16.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
U190684E02
2.115,2.729 2.24,2.979 false 1.677,2.729 1.573,2.979 false 0.365,1.344 0.615,1.833 false 2.094,1.323 2.896,0.521 false 0.104,0.094 0.333,0.292 0.229,0.198 10 false *a 2.104,3 2.438,3.146 0.333,0.146 10 false GND 1.323,3 1.771,3.146 0.448,0.146 10 false SMRB 0.917,2.542 1.146,2.74 0.229,0.198 10 false c6 2,1.615 2.229,1.813 0.229,0.198 10 false k3 2.938,0.406 3.167,0.604 0.229,0.198 10 false + 0.646,1.24 0.875,1.438 0.229,0.198 10 false T6 0.49,1.854 0.823,2 0.333,0.146 10 false CBI

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k3-1 (+) - T6-1 (CBI) Auxiliary battery voltage is not applied between terminals c6-4 (SMRB) and c6-2 (GND) 10 kΩ or higher
k3-1 (+) - T6-1 (CBI) Auxiliary battery voltage is applied between terminals c6-4 (SMRB) and c6-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c6-4 (SMRB) - c6-2 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 35.5 Ω



e.

Install the hybrid battery junction block assembly.



OK

17.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

17.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRG)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS).


c.
U190685E02
2.271,2.719 2.396,2.969 false 2.052,2.719 1.948,2.969 false 0.344,0.75 0.677,1.833 false 2.917,0.771 2.604,0.948 false 0.094,0.083 0.323,0.281 0.229,0.198 10 false *a 1.729,3.01 2.073,3.198 0.344,0.188 10 false GND 2.24,3 2.719,3.177 0.479,0.177 10 false SMRG 0.99,2.531 1.219,2.729 0.229,0.198 10 false c6 0.625,0.802 0.854,1 0.229,0.198 10 false T5 2.125,0.802 2.354,1 0.229,0.198 10 false h3 2.958,0.635 3.083,0.833 0.125,0.198 10 false - 0.604,1.854 0.938,2.052 0.333,0.198 10 false CEI

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h3-1 (-) - T5-1 (CEI) Auxiliary battery voltage is not applied between terminals c6-1 (SMRG) and c6-2 (GND) 10 kΩ or higher
h3-1 (-) - T5-1 (CEI) Auxiliary battery voltage is applied between terminals c6-1 (SMRG) and c6-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c6-1 (SMRG) - c6-2 (GND) -40 to 80°C (-40 to 176°F) 19.0 to 35.5 Ω



e.

Install the hybrid battery junction block assembly.



OK

18.CHECK FUSE (PCU)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

18.CHECK FUSE (PCU)

OK

19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

28.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

OK

20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

OK

21.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK POWER MANAGEMENT CONTROL ECU

OK

22.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

22.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

23.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

23.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

CONNECT SECURELY

24.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

25.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

25.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

26.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

27.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

27.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

28.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)

OK

29.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

30.REPAIR OR REPLACE HARNESS OR CONNECTOR
29.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).



NEXT

REPLACE FUSE (PCU)

30.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PCU)

31.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

32.CHECK GENERATOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

33.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

34.CHECK MOTOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY