Refer to the circuit description for DTC P0A84-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123).
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A85 | 123 | When the output voltage of the battery cooling blower assembly (VM) is too high compared to the target control voltage range* (1 trip detection) | ·
Wire harness or connector ·
Battery cooling blower assembly ·
Battery smart unit ·
HV battery |
*: This DTC is stored when the battery cooling blower assembly is operating. When reproducing the DTC Detection Conditions, perform the Active Test "Driving the Battery Cooling Fan" to operate the battery cooling blower assembly.
Refer to the wiring diagram for DTC P0A84-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A84-123).
Refer to the wiring diagram for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)
Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
A
B
Remove the front seat assembly RH.
for Manual Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL)
for Power Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL)
Turn over the front floor carpet.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check voltage. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-2 (VM0) - S30-4 (GND0) | Battery cooling blower is operating | Below 5 V |
| *a | Component with harness connected
(Battery Cooling Blower Assembly) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage on the wire side of the connector that is part of the battery cooling blower.
Turn the power switch off.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).
Disconnect the z24 battery smart unit connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z24-13 (TB0) - Body ground | Power switch on (IG) | 1 V or less |
| z24-1 (GB0) - Body ground | Power switch on (IG) | 1 V or less |
| z24-14 (TB1) - Body ground | Power switch on (IG) | 1 V or less |
| z24-2 (GB1) - Body ground | Power switch on (IG) | 1 V or less |
| z24-15 (TB2) - Body ground | Power switch on (IG) | 1 V or less |
| z24-3 (GB2) - Body ground | Power switch on (IG) | 1 V or less |
| z24-16 (TB3) - Body ground | Power switch on (IG) | 1 V or less |
| z24-4 (GB3) - Body ground | Power switch on (IG) | 1 V or less |
| z24-17 (TB4) - Body ground | Power switch on (IG) | 1 V or less |
| z24-5 (GB4) - Body ground | Power switch on (IG) | 1 V or less |
| z24-18 (TB5) - Body ground | Power switch on (IG) | 1 V or less |
| z24-6 (GB5) - Body ground | Power switch on (IG) | 1 V or less |
| z24-21 (TC0) - Body ground | Power switch on (IG) | 1 V or less |
| z24-9 (GC0) - Body ground | Power switch on (IG) | 1 V or less |
| z24-22 (TC1) - Body ground | Power switch on (IG) | 1 V or less |
| z24-10 (GC1) - Body ground | Power switch on (IG) | 1 V or less |
| *a | Rear view of wire harness connector
(to Battery Smart Unit) |
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the z24 battery smart unit connector.
Install the No. 1 hybrid battery shield sub-assembly.
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).
Check the wire harness and connectors of the battery temperature sensor and inlet air temperature sensor for abnormalities by sight and touch.
There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.
Install the No. 1 hybrid battery shield sub-assembly.
OK
NG
Remove the front seat assembly RH.
for Manual Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL)
for Power Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL)
Turn over the front floor carpet.
Disconnect the S30 battery cooling blower assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-2 (VM0) - S30-4 (GND0) | Power switch on (IG) | Below 5 V |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Reconnect the S30 battery cooling blower assembly connector.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the front seat assembly RH.
for Manual Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL)
for Power Seat:
(See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL)
Turn over the front floor carpet.
Disconnect the S30 battery cooling blower assembly connector.
Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).
Disconnect the L144 battery smart unit connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S30-2 (VM0) and L144-8 (VM) - Other terminal | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector
(to Battery Smart Unit) |
Reconnect the L144 battery smart unit connector.
Install the No. 1 hybrid battery shield sub-assembly.
Reconnect the S30 battery cooling blower assembly connector.
Install the front floor carpet.
Install the front seat assembly RH.
OK
NG