Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › ENGINE UNIT › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301599 ENGINE UNIT A

2ZR-FXE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A214906

Remove the oil filler cap.


Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A128159

Remove the oil filler cap gasket.


Hide 3.REMOVE ENGINE COVER JOINT BOLT

a.
A214974

Remove the 3 engine cover joint bolts.


Hide 4.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A214973

Remove the bolt and wiring harness clamp bracket.


Hide 11101W 6.REMOVE CAMSHAFT POSITION SENSOR

a.
A214907

Remove the bolt and camshaft position sensor.


Hide 11101J 7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.
A214908

Remove the bolt and camshaft timing oil control valve.


b.

Remove the O-ring from the camshaft timing oil control valve.


Hide 11401G 8.REMOVE CRANKSHAFT POSITION SENSOR

a.
A150855

Remove the bolt and crankshaft position sensor.


Hide 83530 9.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

a.
A150856

Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.


Hide 89615 10.REMOVE KNOCK SENSOR

a.
A152587

Remove the bolt and knock sensor.


Hide 89429E 11.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

a.
A214917

Remove the engine coolant temperature sensor and gasket.


Hide 11201 12.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A214909

Remove the 13 bolts, seal washer and cylinder head cover.

NOTICE:

As the gaskets may stick to the cylinder head cover, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover.



b.
A214910

Remove the 2 gaskets from the camshaft bearing cap.


Hide 11213 13.REMOVE CYLINDER HEAD COVER GASKET

a.
A214911

Remove the cylinder head cover gasket.


Hide 11193 14.REMOVE SPARK PLUG TUBE GASKET

a.
A214912

Pry up the 4 claws of the ventilation baffle plate.

NOTICE:

Do not deform the claws of the ventilation baffle plate more than necessary.



b.
A336839

Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.

NOTICE:
·

As much as possible prevent the spark plug tube gaskets from being deformed. The removed spark plug tube gaskets will be used when reinstalling the new spark plug tube gaskets.

·

Do not damage the cylinder head cover subassembly.

·

Make sure not to damage the spark plug tube gasket and cylinder head cover subassembly when inserting the screwdriver in the joint area.



HINT:

If the cylinder head cover sub-assembly is damaged, smooth the surface with 400-grit sandpaper.



Hide 16031 16.REMOVE WATER INLET SUB-ASSEMBLY

a.
A214927

Remove the bolt, 2 nuts, inlet water sub-assembly and gasket.


Hide 17.REMOVE WATER INLET SUB-ASSEMBLY STUD BOLT

a.

Using an E5 "TORX" socket wrench, remove the 2 stud bolts.

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.



Hide 13540 20.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11302 21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.

Using a 8mm deep socket wrench, remove the stud bolt from the engine mounting bracket RH.


b.
A214919

Remove the 3 bolts and engine mounting bracket RH.


c.
A214920

Remove the 4 bolts and oil filter bracket.


d.
A214921

Remove the 2 O-rings.


e.
A214922E01
1.797,2.266 2.233,1.927 2.233,1.927 2.795,1.927 false 2.845,1.844 3.025,2.018 0.180,0.174 10 *1

Remove the 18 bolts and gasket.

Text in Illustration
*1 Gasket


f.

Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

A352276E01
4.448,1.906 4.979,0.573 4.979,0.573 2.688,0.802 false 4.302,4.094 2.844,4.469 2.844,4.469 2.635,3.771 false 5.042,0.479 5.354,0.677 0.313,0.198 10 false *1 2.667,4.448 2.979,4.646 0.313,0.198 10 false *1

Text in Illustration
*1 Protective Tape

NOTICE:
·

Be careful not to damage the contact surfaces of the timing chain cover, cylinder block, and cylinder head.

·

Pry the timing chain cover out evenly in order to prevent damaging the knock pins.



HINT:

Tape the screwdriver tip before use.



g.
A214924

Remove the 3 O-rings.


h.

Place the timing chain cover on wooden blocks.


Hide 11302A 22.REMOVE TIMING CHAIN COVER OIL SEAL

a.

Place the timing chain cover on wooden blocks.


b.
A214928E01
2.717,0.558 2.875,0.714 0.158,0.156 10 *1 3.028,1.443 3.210,1.586 0.183,0.143 10 *2 1.721,1.461 2.545,0.638 2.545,0.638 2.663,0.638 false 2.624,1.301 2.959,1.53 2.959,1.53 2.199,1.985 false

Using a screwdriver and hammer, knock out the oil seal.

Text in Illustration
*1 Protective Tape
*2 Wooden Block

HINT:

Tape the screwdriver tip before use.


NOTICE:

Do not damage the surface of the oil seal press fit hole.



Hide 13561 24.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13562 25.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13521 27.REMOVE CRANKSHAFT TIMING SPROCKET

Hide 13507 28.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 19315 29.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A150874

Remove the crankshaft position sensor plate.


Hide 13521A 30.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A150909E09
0.657,0.69 0.832,0.868 0.174,0.178 10 *1 0.857,0.763 0.964,0.763 0.964,0.763 1.178,1.335 false

Using a screwdriver, remove the 2 crankshaft timing gear keys.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 13050 31.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 11114A 37.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 13801 38.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A150886

Remove the 16 valve rocker arms.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 39.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A150887

Remove the 16 valve lash adjusters from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 40.REMOVE VALVE STEM CAP

a.
A214987

Remove the 16 valve stem caps.

HINT:

Arrange the removed parts in the correct order.



Hide 15678A 41.REMOVE OIL CONTROL VALVE FILTER

a.
A214942

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 42.REMOVE NO. 1 CAMSHAFT BEARING

a.
A214943

Remove the 2 camshaft bearings.


Hide 11821 43.REMOVE NO. 2 CAMSHAFT BEARING

a.
A150885

Remove the 2 camshaft bearings.


Hide 11103 44.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 12204 47.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A150899

Remove the ventilation valve sub-assembly.


Hide 12101A 48.REMOVE OIL PAN DRAIN PLUG

a.
A150893

Remove the drain plug and gasket.


Hide 12102A 49.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 11420 51.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A150897

Uniformly loosen and remove the 11 bolts.


b.
A150898E14
0.448,3.073 0.604,3.479 0.604,3.479 0.604,3.604 true 1.177,3.542 1.344,3.948 1.344,3.948 1.344,4.073 true 2.479,3.365 2.646,3.771 2.646,3.771 2.646,3.896 true 3.083,2.635 3.25,3.031 3.25,3.031 3.25,3.156 true 0.521,3.635 0.719,3.823 0.198,0.188 10 false *1 1.25,4.104 1.448,4.292 0.198,0.188 10 false *1 2.552,3.938 2.75,4.125 0.198,0.188 10 false *1 3.156,3.177 3.354,3.365 0.198,0.188 10 false *1

Using a screwdriver, remove the stiffening crankcase by prying between the stiffening crankcase and cylinder block.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the crankcase and cylinder block.



Hide 11432A 52.REMOVE NO. 1 TAPER SCREW PLUG

a.
A235913

Remove the 2 No. 1 taper screw plugs.


Hide 11421 53.REMOVE STIFFENING CRANKCASE STUD BOLT

a.

Using an E5 "TORX" socket wrench, remove the 2 stud bolts.

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.



Hide 54.REMOVE STIFFENING CRANKCASE RING PIN

a.

Remove the 2 ring pins.

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.



Hide 11401L 55.REMOVE ENGINE REAR OIL SEAL

a.
A206144

Remove the engine rear oil seal from the cylinder block.