Upon receiving the dynamic radar cruise control system operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.
Upon receiving the emergency brake signal operating signal from the skid control ECU, the relay contact turns on and the stop light blinks (for vehicles with a emergency brake signal).
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1380/64 | 761 | When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is ON, a signal is not input to the STP2 and EXO terminals for 2 seconds or more. | ·
Stop light switch ·
Stop light switch circuit ·
Stop light control relay ·
Stop light control relay circuit ·
Brake booster with master cylinder (Skid control ECU) |
| ↑ | 762 | When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is OFF, the signal at the STP terminal is different from the input signal at the STP2 and EXO terminals for 5 seconds or more. | ↑ |
Refer to DTC C1249/49 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1249/49).
When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
When C1249/49 is output together with C1380/64, inspect and repair the trouble areas indicated by C1249/49 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1249/49).
Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | ON |
| Brake pedal released | OFF |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
OK
NG
Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay | Relay ON/OFF | Stop lights come on |
| EBS Relay*1 | Stop light control relay (Emergency brake signal) | Relay ON/OFF | ·
Hazard warning switch OFF ·
Stop light switch ON |
*1: w/ Emergency Brake Signal
Perform the Active Test of the stop light control relay using the GTS.
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay Output | Stop light control relay output / ON or OFF | ON: Relay output on
OFF: Relay output off |
- |
| EBS Relay*1 | Stop light control relay (Emergency brake signal) / ON or OFF | ON: Relay on
OFF: Relay off |
·
Hazard warning switch OFF ·
Stop light switch ON |
*1: w/ Emergency Brake Signal
Check for stop light control relay operation using the Data List and stop light operation by performing an Active Test.
| Result | Proceed to |
|---|---|
| Data List content and stop light operation are normal | A |
| Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off | B |
A
B
Turn the power switch off (lock).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-6 (STP2) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V |
| A58-6 (STP2) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
OK
NG
Reconnect the skid control ECU connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC (C1380/64) is not output | A |
| DTC (C1380/64) is output (for LHD) | B |
| DTC (C1380/64) is output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the power switch off (lock).
Inspect the stop light control relay (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT CONTROL RELAY>INSPECTION).
The stop light control relay is normal.
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the stop light control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-3 (STP0) - A28-9 (ACC) | Always | Below 1 Ω |
| A58-3 (STP0) - Body ground | Always | 10 kΩ or higher |
| A58-21 (EXO) - A28-4 (ESS1)* | Always | Below 1 Ω |
| A58-21 (EXO) - Body ground* | Always | 10 kΩ or higher |
*: w/ Emergency Brake Signal
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Turn the power switch off (lock).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-33 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V |
| A58-33 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C