Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2013.08–2014.11
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301840 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause brackets of the air conditioning unit assembly to break.

·

When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
E280007

Temporarily install the air conditioning unit assembly with the bolt and nut.


b.

Connect the No. 1 cooler unit drain hose as shown in the illustration.

NOTICE:

Connect the No. 1 cooler unit drain hose firmly to prevent water leaks.



Hide 55330B 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Install the instrument panel reinforcement assembly with the 6 bolts <A>.

E228529E03
4.948,5.302 5.177,5.5 0.229,0.198 10 true (1) 6.448,4.719 6.698,4.885 0.25,0.167 10 true (2) 3.323,5.396 3.552,5.583 0.229,0.188 10 true (3) 0.333,1.667 0.51,1.854 0.177,0.188 10 true *1 0.125,2.25 0.302,2.438 0.177,0.188 10 true *1 3.063,2.135 3.24,2.323 0.177,0.188 10 true *1 4.104,1.094 4.281,1.281 0.177,0.188 10 true *1 6.365,1.25 6.542,1.438 0.177,0.188 10 true *1 6.5,1.823 6.677,2.01 0.177,0.188 10 true *1 3.375,5.771 3.552,5.958 0.177,0.188 10 true *2 6.542,5.094 6.719,5.281 0.177,0.188 10 true *2 5,5.698 5.177,5.885 0.177,0.188 10 true *2

Text in Illustration
*1 Bolt <A> *2 Bolt <B>

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Install the air conditioning unit assembly with the 3 bolts <B>.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


c.

Connect each connector.

E250083E01
5.471,1.828 5.621,1.985 0.150,0.157 10 *1 5.629,1.928 5.917,2.145 false

Text in Illustration
*1 Center Airbag Sensor Connector - -


d.

Engage the 2 clamps.


e.

Connect the center airbag sensor connector to the center airbag sensor assembly as shown in the illustration.


f.

Check that there is no looseness in the installation parts of the center airbag sensor assembly.


g.

Engage the 4 clamps.


h.

Install the 2 bolts.


i.

Install the bolt to connect the earth wire.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


j.

Engage the 5 clamps.


k.

Install the bolt.


Hide 3.INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.
E280008

Install the air conditioning unit assembly with the bolt and nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87212 4.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 8 claws to install the rear No. 1 air duct.


b.

Engage the clamp.


Hide 55990B 5.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

a.

Engage the guide and 2 claws.


b.

Install the lower defroster nozzle assembly with the 2 clips.


c.

Engage the 2 clamps.


Hide 55307C 6.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 2 instrument panel brace sub-assembly with the screw and nut.

Torque:
Screw : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Engage the 3 clamps.


c.

Install the bolt to connect the earth wire.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.

Engage the 3 clamps.


e.

Install the 2 bolts.


f.

Engage the clamp.


g.

Install the screw.


h.

Install the bolt to connect the earth wire.


Hide 55376 7.INSTALL NO. 1 INSTRUMENT PANEL MOUNTING BRACKET

a.

Install the No. 1 instrument panel mounting bracket with the 2 bolts and 2 nuts.

Torque:
Bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Install the floor carpet with the clip.


Hide 55306A 8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the screw and nut.

Torque:
Screw : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Engage the each clamp.


Hide 55377A 9.INSTALL NO. 2 INSTRUMENT PANEL MOUNTING BRACKET

a.

Install the No. 2 instrument panel mounting bracket with the bolt and 2 nuts.

Torque:
Bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Install the floor carpet with the clip.


Hide 88625Q 10.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.

Connect the connector and aspirator, and install the cooler thermistor (room temperature sensor).


Hide 55309C 11.INSTALL CENTER INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY

a.

Install the center instrument panel reinforcement sub-assembly with the 2 nuts.


b.

Engage the clamp.


Hide 85940 12.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 82730 13.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

Hide 17.INSTALL STEERING POST ASSEMBLY

Hide 55303B 18.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 87246A 19.CONNECT OUTLET HEATER WATER HOSE A

a.

Using pliers, grip the claws of the clip and slide the clip to connect the outlet heater water hose A.


Hide 87245A 20.CONNECT INLET HEATER WATER HOSE A

a.

Using pliers, grip the claws of the clip and slide the clip to connect the inlet heater water hose A.


Hide 88710E 21.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:
·

Keep the O-ring and O-ring fitting surfaces clean from dirt or any foreign objects.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.




d.

Install the air conditioner tube and accessory assembly.


Hide 88707 22.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:
·

Keep the O-ring and O-ring fitting surfaces clean from dirt or any foreign objects.

·

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in a leakage of electric power.




d.

Install the suction pipe sub-assembly.


e.

Move the hook connector in the direction indicated by the arrow in the illustration.


f.
E223810

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 55701J 23.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55736D 24.INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

Hide 55701J 25.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735C 26.INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

Hide 27.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 29. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))

Hide 30. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))