1. PRECAUTION
Make sure to select DEF mode before disconnecting the cable from the negative (-) auxiliary battery terminal.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55736D
4.REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD)
55701J
5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55735C
6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH (for RHD)
55701J
7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
88707
8.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
9.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Disconnect the air conditioner tube and accessory assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
87245A
10.DISCONNECT INLET HEATER WATER HOSE A
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.
Do not apply excessive force to the inlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
87246A
11.DISCONNECT OUTLET HEATER WATER HOSE A
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.
Do not apply excessive force to the outlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
55303B
12.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
13.REMOVE STEERING POST ASSEMBLY
82877
14.REMOVE ECU INTEGRATION BOX RH (for LHD)
82878
15.REMOVE ECU INTEGRATION BOX LH (for RHD)
82877
16.REMOVE ECU INTEGRATION BOX RH (for RHD)
82730
17.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
85940
18.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)
55309C
19.REMOVE CENTER INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY
Disengage the clamp.
Remove the 2 nuts and center instrument panel reinforcement sub-assembly.
88625Q
20.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Disconnect the aspirator and connector, and remove the cooler thermistor (room temperature sensor).
55377A
21.REMOVE NO. 2 INSTRUMENT PANEL MOUNTING BRACKET
Using a clip remover, remove the clip and turn back the floor carpet.
Remove the bolt and 2 nuts, and No. 2 instrument panel mounting bracket.
55306A
22.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Disengage the 4 clamps.
Remove the screw, nut, and No. 1 instrument panel brace sub-assembly.
55376
23.REMOVE NO. 1 INSTRUMENT PANEL MOUNTING BRACKET
Using a clip remover, remove the clip and turn back the floor carpet.
Remove the 2 bolts, 2 nuts, and No. 1 instrument panel mounting bracket.
55307C
24.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire |
Remove the bolt.
Disengage the clamp.
Remove the 2 bolts.
Disengage the 3 clamps.
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire |
Disengage the 3 clamps.
Remove the screw, nut, and No. 2 instrument panel brace sub-assembly.
55990B
25.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
Disengage the 2 clamps.
Using a clip remover, remove the 2 clips.
Disengage the 2 claws and guide, and remove the lower defroster nozzle assembly.
87212
26.REMOVE REAR NO. 1 AIR DUCT
Disengage the clamp.
Disengage the 8 claws and remove the rear No. 1 air duct.
55330B
27.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Remove the bolt.
Disengage the 3 clamps.
Disengage the 2 clamps.
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire |
Remove the 2 bolts.
Disengage the 4 clamps.
Disconnect the center airbag sensor connector from the center airbag sensor assembly as shown in the illustration.
| *1 | Center Airbag Sensor Connector | - | - |
Disengage the 2 clamps.
Disconnect each connector.
Remove the 9 bolts and instrument panel reinforcement assembly.
28.REMOVE AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Disconnect the No. 1 cooler unit drain hose.
Remove the bolt, nut and air conditioning unit assembly.