Home › Engine / Hybrid System › 2ZR-FXE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2020.08
RM2070E _51 Engine / Hybrid System _061910 2ZR-FXE INTAKE / EXHAUST _0301618 EXHAUST MANIFOLD A

2ZR-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install 2 new gaskets.


b.

Temporarily install the exhaust manifold and manifold stay with the 7 nuts and 3 bolts.

HINT:

The type B and type C are non-reusable.


A307472E01
3.842,0.697 4.036,0.911 0.193,0.214 12 *A 4.823,0.697 5.016,0.911 0.193,0.214 12 *B 5.888,0.697 6.090,0.911 0.202,0.214 12 *C 4.989,1.8 5.682,2.143 0.693,0.343 10 18 mm (0.709 in.) 6.117,1.8 6.810,2.143 0.693,0.343 10 17 mm (0.669 in.) 5.822,0.651 6.867,2.174 1.045,1.523 4.763,0.651 5.776,2.166 1.014,1.514 3.795,0.651 4.7,2.174 0.904,1.523

Text in Illustration
*A Type A *B Type B
*C Type C - -


c.

Tighten the 7 nuts.

Torque:
Type A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Type B : 37 N*m (377 kgf*cm, 27 ft.*lbf)
Type C : 26 N*m (265 kgf*cm, 19 ft.*lbf)


d.

Tighten the 3 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 58151 5.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator with the 3 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum (front) 41.5 mm (1.64 in.)
Minimum (rear) 38.5 mm (1.52 in.)

HINT:

If the free length is less than the minimum, replace the compression spring.



b.

Fully insert 2 new gasket to the exhaust manifold and front exhaust pipe assembly.


c.
A181728E53
1.354,0.458 1.51,0.458 1.51,0.458 1.833,1.115 false 2.042,2.427 2.042,3.24 2.042,3.24 1.75,3.24 false 2.51,1.365 2.823,1.552 2.823,1.552 2.823,1.781 false 1.156,0.396 1.365,0.667 0.208,0.271 10 false *1 1.542,3.146 1.76,3.396 0.219,0.25 10 false *2 2.729,1.802 2.948,2.083 0.219,0.281 10 false *a

Using a plastic hammer and wooden block, tap in each gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.

Text in Illustration
*1 Exhaust Manifold and Front Exhaust Pipe Assembly
*2 Gasket
*a Wooden Block

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly with the 4 bolts and 4 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 51441 9.INSTALL NO. 1 ENGINE UNDER COVER

Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 12.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55736D 13.INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

Hide 55735C 14.INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

Hide 15.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 16.INSPECT FOR EXHAUST GAS LEAK