13405
1.INSTALL FLYWHEEL SUB-ASSEMBLY
Gently place the engine assembly onto wood blocks or equivalent.
This step should be done while hanging the engine assembly using the engine hangers and a chain block.
Install the flywheel sub-assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>INSTALLATION).
31270
2.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
Install the transmission input damper assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>REAR CRANKSHAFT OIL SEAL>INSTALLATION).
30900
3.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
Install the hybrid vehicle transaxle assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION).
Be careful not to apply excessive force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excessive force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.
82121
4.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
11363A
5.INSTALL FLYWHEEL HOUSING SIDE COVER
28193
6.INSTALL STARTER HOLE INSULATOR
16577C
7.INSTALL RADIATOR PIPE
Install the radiator pipe with the 2 bolts.
Connect the No. 3 radiator hose and slide the clamp to secure it.
12305
8.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator RH is necessary.
Position the engine mounting insulator sub-assembly RH as shown in the illustration.
Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.
Tighten the 3 bolts in the order of the bolt (B), bolt (C) and bolt (A).
Connect the earth wire clamp to the engine mounting insulator sub-assembly RH.
Install the 2 cooler brackets with the 2 bolts.
12372A
9.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Temporarily install the engine mounting insulator LH with the 4 bolts.
Tighten the 4 bolts in the order of the bolt (C), bolt (B), bolt (D) and bolt (A).
12371A
10.INSTALL REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Install the rear engine mounting insulator to the engine mounting bracket with the through bolt.
12361A
11.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Temporarily install the front engine mounting insulator with the bolt and nut.
12.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on the engine lifter.
Install height adjustment attachments and plate lift attachments under the engine assembly with transaxle.
Do not position a height adjustment attachment or plate lift attachment under the front cross member sub-assembly.
Place the engine assembly on wooden blocks or equivalent so that the engine assembly is level.
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember sub-assembly to the position where the engine mounting insulator RH and engine mounting insulator LH can be installed.
Do not raise the engine assembly more than necessary. If the engine assembly is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly is clear of all wiring and hoses.
While raising the engine assembly into the vehicle, do not allow it to contact the vehicle.
Install the front crossmember sub-assembly with the 4 bolts.
Install the front engine mounting insulator to the front crossmember sub-assembly with the 2 bolts.
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Install the engine mounting insulator LH with the through bolt and nut.
When installing the engine mounting insulator LH, tighten the nut while holding the bolt.
Install the engine mounting insulator RH with the bolt and 2 nuts.
Tighten the front engine mounting insulator with the bolt and nut.
51201
13.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
52258A
14.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH
52257
15.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH
Perform the same procedure as for the LH side.
51108A
16.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
17.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
51425A
18.INSTALL FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT
43040B
19.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
43030B
20.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH
Perform the same procedure as for the LH side.
43420
21.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
22.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
23.INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH
48068
24.INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48810
25.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
48820B
26.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
45047
27.CONNECT TIE ROD END SUB-ASSEMBLY LH
45046
28.CONNECT TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
89543
29.INSTALL FRONT SPEED SENSOR LH
89542
30.INSTALL FRONT SPEED SENSOR RH
Perform the same procedure as for the LH side.
43502H
31.INSTALL FRONT AXLE SHAFT NUT LH
43501H
32.INSTALL FRONT AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
17410
33.INSTALL FRONT EXHAUST PIPE ASSEMBLY
57533B
34.INSTALL FRONT CENTER FLOOR BRACE
51442A
35.INSTALL FRONT NO. 3 ENGINE UNDER COVER
45025D
36.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
37.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)
45259A
38.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)
82121
39.CONNECT ENGINE WIRE
Connect the engine wire with the 2 clamps.
Install the earth wire with the bolt.
Connect the wire harness with the 3 clamps.
Connect the wire harness to the engine room junction block.
Connect the 2 connectors and 2 clamps to the engine room junction block.
Connect the ECM connector with the lock lever.
Connect the 2 clamps.
88370
40.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
23901
41.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube connector and fuel pipe.
Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a "click" sound. If the connection is tight, apply a small amount of engine oil to the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.
Install the No. 1 fuel pipe clamp.
23826
42.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose and slide the clamp to secure it.
43.CONNECT HEATER HOSE
Connect the heater hose and slide the clamp to secure it.
87245A
44.CONNECT INLET HEATER WATER HOSE
Connect the inlet heater water hose and slide the clamp to secure it.
87246A
45.CONNECT OUTLET HEATER WATER HOSE
Connect the outlet heater water hose and slide the clamp to secure it.
G9229A
46.CONNECT NO. 5 INVERTER COOLING HOSE
Connect the No. 5 inverter cooling hose and slide the clamp to secure it.
G9227A
47.CONNECT NO. 3 INVERTER COOLING HOSE
Connect the No. 3 inverter cooling hose and slide the clamp to secure it.
16281
48.CONNECT NO. 4 WATER BY-PASS HOSE
Connect the No. 4 water by-pass hose and slide the clamp to secure it.
16572D
49.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose and slide the clamp to secure it.
16571C
50.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose and slide the clamp to secure it.
G9219A
51.INSTALL INVERTER TRAY BRACKET
Position the inverter tray bracket as shown in the illustration.
Temporarily install the inverter tray bracket with the 5 bolts.
Tighten the 5 bolts in the order of the bolt (A), bolt (C), bolt (D), bolt (E) and bolt (B).
Connect the 2 clamps to the inverter tray bracket.
G92A0A
52.INSTALL INVERTER RESERVE TANK ASSEMBLY
Temporarily install the inverter reserve tank assembly with the 2 bolts.
Tighten the 2 bolts in the order of the bolt (B) and bolt (A).
G9200
53.INSTALL INVERTER WITH CONVERTER ASSEMBLY
G9228B
54.CONNECT WATER HOSE
82112
55.CONNECT NO. 2 ENGINE ROOM WIRE
G9221
56.REMOVE INVERTER COVER
82122
57.CONNECT NO. 2 ENGINE WIRE
G1148
58.CONNECT MOTOR CABLE
G2148
59.CONNECT GENERATOR CABLE
82164
60.CONNECT FRAME WIRE
61.CHECK HIGH VOLTAGE CABLE CONNECTION
G9221
62.INSTALL INVERTER COVER
82111
63.CONNECT ENGINE ROOM MAIN WIRE
G9214
64.INSTALL NO. 1 INVERTER BRACKET
65.INSTALL AIR CLEANER HOSE ASSEMBLY
66.INSTALL AIR CLEANER CASE
Install the air cleaner case with the 3 bolts.
Connect the No. 4 water by-pass hose to the air cleaner case with the 3 clamps.
Install the air cleaner filter element.
17750A
67.INSTALL INLET AIR CLEANER ASSEMBLY
Install the inlet air cleaner assembly with the 2 bolts.
17705
68.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
Install the air cleaner filter element.
Install the air cleaner cap sub-assembly with the 2 clamps and hose band.
Connect the air flow meter connector.
G3834
69.INSTALL SERVICE PLUG GRIP
70.ADD HYBRID TRANSAXLE FLUID
71.INSPECT HYBRID TRANSAXLE FLUID
72.ADD COOLANT (for Engine)
73.ADD COOLANT (for Inverter)
75.INSPECT ENGINE OIL LEVEL
76.INSPECT FOR FUEL LEAK
77.INSPECT FOR COOLANT LEAK (for Engine)
78.INSPECT FOR COOLANT LEAK (for Inverter)
79.INSPECT FOR OIL LEAK
80.INSPECT FOR EXHAUST GAS LEAK
51442E
81.INSTALL NO. 2 ENGINE UNDER COVER
51441
82.INSTALL NO. 1 ENGINE UNDER COVER
52618A
83.INSTALL FRONT LOWER BUMPER ABSORBER
51444A
84.INSTALL REAR ENGINE UNDER COVER LH
51443C
85.INSTALL REAR ENGINE UNDER COVER RH
86.INSTALL FRONT WHEELS
87.CHECK FRONT WHEELS FACING STRAIGHT AHEAD
88.INSPECT IGNITION TIMING
89.INSPECT ENGINE IDLE SPEED
91.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
53289A
92.INSTALL RADIATOR SUPPORT OPENING COVER
11212
93.INSTALL NO. 2 CYLINDER HEAD COVER
Engage the 3 clips to install the No. 2 cylinder head cover.
Be sure to engage the clips securely.
Do not apply excessive force or hit the No. 2 cylinder head cover to engage the clips. This may cause the No. 2 cylinder head cover to break.
94.CHECK FOR SPEED SENSOR SIGNAL