Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the key is in the vehicle and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



WIRING DIAGRAM

B452140E04
4.979,1.656 5.656,1.802 0.677,0.146 10 false IG1 NO. 1 4.99,3.219 5.667,3.365 0.677,0.146 10 false IG1 NO. 2 4.99,4.635 5.667,4.781 0.677,0.146 10 false IG1 NO. 3 5.156,6.063 5.583,6.208 0.427,0.146 10 false ACC 3.99,6.792 6.938,7.031 2.948,0.24 10 false Instrument Panel Junction Block Assembly 2.25,2.24 2.448,2.385 0.198,0.146 10 false 28 2.531,2.438 2.979,2.583 0.448,0.146 10 false SSW1 2.24,2.708 2.438,2.854 0.198,0.146 10 false 30 2.542,2.875 2.99,3.021 0.448,0.146 10 false SSW2 1.385,2.344 1.49,2.49 0.104,0.146 10 false 5 1.385,2.771 1.49,2.917 0.104,0.146 10 false 1 1.042,2.875 1.354,3.021 0.313,0.146 10 false SS2 1.031,2.427 1.344,2.573 0.313,0.146 10 false SS1 0.542,3.229 0.979,3.385 0.438,0.156 10 false L194 0.542,3.385 1.49,3.542 0.948,0.156 10 false Power Switch 0.292,5.438 1.208,5.594 0.917,0.156 10 false A93 0.281,5.594 2.115,5.75 1.833,0.156 10 false Stop Light Switch Assembly 0.323,6.094 0.792,6.24 0.469,0.146 10 false STOP 1.094,5.948 2.771,6.271 1.677,0.323 10 false from Auxiliary Battery 1.24,5.125 1.625,5.302 0.385,0.177 10 false GND 1.26,4.792 1.604,4.938 0.344,0.146 10 false OUT 1.323,0.938 1.979,1.167 0.656,0.229 10 false ECU-B2 0.115,0.771 1.063,1.094 0.948,0.323 10 false from Auxiliary Battery 3.458,1.177 3.563,1.323 0.104,0.146 10 false 6 2.969,1.365 3.344,1.51 0.375,0.146 10 false IG1D 2.208,7.979 3.792,8.354 1.583,0.375 10 false Certification ECU (Smart Key ECU Assembly) 2.281,0.625 2.385,0.771 0.104,0.146 10 false 2 2.146,0.813 2.542,0.958 0.396,0.146 10 false L195 2.542,0.813 2.99,0.958 0.448,0.146 10 false +B 0.323,4.708 0.646,5.052 0.323,0.344 10 false 7 1.708,4.708 2.031,5.052 0.323,0.344 10 false 1 1.708,5.052 2.031,5.396 0.323,0.344 10 false 2 0.563,4.729 1.01,4.875 0.448,0.146 10 false B 2.229,4.615 2.458,4.76 0.229,0.146 10 false 18 2.521,4.802 2.969,4.948 0.448,0.146 10 false STP1 2.229,7.26 2.458,7.406 0.229,0.146 10 false 11 2.531,7.438 2.979,7.583 0.448,0.146 10 false E 3.458,5.583 3.656,5.729 0.198,0.146 10 false 4 3.917,5.583 4.115,5.729 0.198,0.146 10 false 43 3.906,5.771 4.188,5.917 0.281,0.146 10 false 2A 3.906,1.177 4.104,1.323 0.198,0.146 10 false 25 3.906,1.344 4.188,1.49 0.281,0.146 10 false 2B 3.885,0.75 4.302,0.896 0.417,0.146 10 false 1*1 3.906,0.927 4.188,1.073 0.281,0.146 10 false 2E 2.885,5.76 3.333,5.906 0.448,0.146 10 false ACCD 5.938,5.542 6.667,5.792 0.729,0.25 10 false ECU-ACC 6.073,2.615 6.667,2.823 0.594,0.208 10 false WIP 5.917,1.073 6.438,1.385 0.521,0.313 10 false ECU-IG NO. 1 5.99,4.094 6.688,4.406 0.698,0.313 10 false SEAT HTR FR 6.51,0.76 6.708,0.906 0.198,0.146 10 false 19 6.521,2.313 6.719,2.458 0.198,0.146 10 false 11 6.521,3.729 6.719,3.875 0.198,0.146 10 false 21 6.531,3.906 6.813,4.052 0.281,0.146 10 false 2A 6.542,5.177 6.74,5.323 0.198,0.146 10 false 34 6.552,6.135 6.75,6.281 0.198,0.146 10 false 6 6.521,6.323 6.802,6.469 0.281,0.146 10 false 2B 3.333,1.365 3.729,1.51 0.396,0.146 10 false L197 2.146,7.448 2.542,7.594 0.396,0.146 10 false L195 2.135,4.802 2.531,4.948 0.396,0.146 10 false L195 3.344,5.76 3.74,5.906 0.396,0.146 10 false L197 2.156,2.885 2.552,3.031 0.396,0.146 10 false L197 2.156,2.427 2.552,2.573 0.396,0.146 10 false L197 4.24,0.927 4.521,1.073 0.281,0.146 10 false 2F 4.219,0.75 4.719,0.906 0.5,0.156 10 false 1*2 4.042,8.115 5.49,8.354 1.448,0.24 10 false *1: for LHD 4.042,8.448 5.49,8.688 1.448,0.24 10 false *2: for RHD 6.531,5.344 6.813,5.49 0.281,0.146 10 false 2B 6.521,2.479 6.802,2.625 0.281,0.146 10 false 2A 6.51,0.938 6.792,1.083 0.281,0.146 10 false 2A

B298915E31
3.813,1.865 4.115,2.063 0.302,0.198 10 false IG2 3.104,1.563 3.375,1.729 0.271,0.167 10 false 1A 3.156,1.385 3.292,1.552 0.135,0.167 10 false 2 4.635,1.563 4.896,1.729 0.26,0.167 10 false 1A 4.688,1.396 4.823,1.563 0.135,0.167 10 false 3 3.01,2.24 5.115,2.76 2.104,0.521 10 false No.2 Integration Relay (Engine Room Relay Block and Junction Block Assembly) 0.896,3.26 2.396,3.615 1.5,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.927,1.563 2.292,1.813 0.365,0.25 10 false L195 2.042,1.385 2.177,1.552 0.135,0.167 10 false 9 1.563,1.552 1.938,1.719 0.375,0.167 10 false IG2D

CAUTION / NOTICE / HINT

NOTICE:
·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor

·

Key Certif Wait T-Out


-


PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock function by operating the electrical key transmitter sub-assembly (See pgeVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Wireless door lock function operates.




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO OTHER DIAGNOSTIC PROCEDURE (All Door Entry Lock/Unlock Functions and Wireless)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENTRY AND START SYSTEM
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly (See pageVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


b.
B337177E08
0.458,1.802 0.958,1.802 0.958,1.802 1.115,1.344 false 2.146,0.625 2.385,0.25 2.385,0.25 2.865,0.25 false 0.302,1.719 0.677,1.927 0.375,0.208 10 false *1 2.917,0.177 3.125,0.385 0.208,0.208 10 false *2

With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


Result:
Result Proceed to
The power source mode does not change A
The power source mode changes. B



Text in Illustration
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


A

5.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

12.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
5.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Enter the following menus: Body Electrical / Power Source Control / Data List.


d.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning , the hybrid control system can be started by pressing and holding the power switch for a certain period of time.



OK:

The Techstream display changes correctly in response to the brake pedal operation.




OK

6.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - POWER SOURCE AND GRAND)
6.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the Techstream.


b.

With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off (ACC and IG)
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

OK:

IG2 ON is displayed on the Techstream screen.


HINT:

If the smart entry and start system (for Start Function) has been canceled on the customization menu, ACC ON is displayed on the Techstream screen.




OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

8.CHECK FOR DTC
7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Read the Data List according to the display on the Techstream.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition State of power supply IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off (power supply off)
ACC ON: Power switch on (ACC) (ACC relay on)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Starting hybrid control systeml
Since IG1 ON and IG2 ON turn "on" at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).


b.

Measure the voltage while reading the Data List on the Techstream.

U190839E02
4.375,1.625 4.115,2.292 true 1.979,1.74 1.76,2.292 true 4.542,1.635 4.708,2.302 true 0.302,0.292 0.49,0.448 0.188,0.156 10 false *a 4.781,0.938 5.271,1.177 0.49,0.24 10 false L197 2.177,0.938 2.542,1.167 0.365,0.229 10 false L195 3.927,2.313 4.292,2.469 0.365,0.156 10 false IG1D 1.531,2.313 1.896,2.469 0.365,0.156 10 false IG2D 4.563,2.313 5.052,2.469 0.49,0.156 10 false ACCD

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

Standard Voltage:
Tester Connection Condition Specified Condition
L197-6 (IG1D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
L195-9 (IG2D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
EL197-4 (ACCD) - Body ground Power switch off 1 V or less
Power switch on (IG) 8.5 V or higher
Power switch on (ACC) 8.5 V or higher




OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK FOR DTC
a.

Enter the following menus: Body Electrical / Smart Key / Trouble Codes.


b.

Check for DTCs.

Result:
Result Proceed to
The following DTCs are not output:
·

B2785

·

B2784

·

B278A


A
The following DTCs are output:
·

B2784

·

B278A


B
The following DTCs are not output:
·

B2785


C




A

REPAIR ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - POWER SOURCE AND GRAND)

OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH)

OK

11.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

12.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Enter the following menus: Body Electrical / Power Source Control / Data List.


d.

Read the Data List according to the display on the Techstream.


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the power switch input signal is malfunctioning


Start Switch2 Power switch 2 status ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.



OK:

The Techstream display changes correctly in response to the power switch operation.



OK

NG

13.INSPECT POWER SWITCH
13.INSPECT POWER SWITCH
a.

Remove the power switch.


b.

Inspect the power switch.



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)

NG

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)
a.

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L194 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L197-28 (SSW1) - L194-5 (SS1) Always Below 1 Ω
L197-30 (SSW2) - L194-1 (SS2) Always Below 1 Ω
L197-28 (SSW1) or L194-5 (SS1) - Body ground Always 10 kΩ or higher
L197-30 (SSW2) or L194-1 (SS2) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR