DTC P3190 Poor Engine Power |
DTC P3191 Engine does not Start |
| DTC No. | DTC Detection Condition | Trouble Area |
| P3190 | When all of the following conditions are met (1 trip detection logic):
|
|
| P3191 | When all of the following conditions are met (1 trip detection logic):
|
|
| ECM (Powertrain / Engine and ECT / Data List) | |||
| HV Target Engine Speed | Engine Speed | Requested Engine Torque | Actual Engine Torque |
| Throttle Position Command | Throttle Position No. 1 | Calculate Load | Coolant Temp |
| Short FT #1 | Long FT #1 | EGR Step Position | - |
| POWER MANAGEMENT CONTROL ECU (Powertrain / Hybrid Control / Data List) | |||
| Target Engine Rev | Engine Revolution | Requested Engine Torque | Engine Coolant Temp |
| Engine Idling Request | - | - | - |
| Related DTCs | P3190: Poor engine power P3191: Engine does not start |
| Required sensors / components (Main) | Crankshaft position sensor |
| Required sensors / components (Related) | Power management control ECU |
| Frequency of operation | Continuous |
| Duration | 100 engine revolutions or 6 seconds |
| MIL operation | Immediately |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not present | None |
| Fuel cut operation | Not operated |
| Engine speed | 650 rpm or more (varies with engine coolant temperature) |
| Time for low engine torque | 100 engine revolutions or more, and 6 seconds or more (varies with engine coolant temperature) |
| Fuel level | Not empty |
| Ratio of estimated torque against target torque | Less than 20% |
| Engine start no-determination time (receive from power management control ECU) | 100 engine revolutions or more, and 6 seconds or more (varies with engine coolant temperature) |
| Fuel level | Not empty |
| Engine speed is a fixed value or more | - |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P3190 or P3191 is output | A |
| DTC P3193 is output | B |
| DTC P3190, P3191 and/or P3193 and other DTCs are output | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK SHORTAGE OF FUEL |
Check the amount of fuel remaining.
|
| ||||
| OK | |
| 3.CLEAR DTC |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| NEXT | |
| 4.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 5.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP |
|
| ||||
| OK | |
| 6.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 7.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY |
Inspect the throttle body with motor assembly (Click here).
|
| ||||
| OK | |
| 8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | |
| 9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 10.INSPECT CRANK POSITION SENSOR |
Inspect the crank position sensor (Click here).
|
| ||||
| OK | |
| 11.INSPECT CAM POSITION SENSOR |
Inspect the cam position sensor (Click here).
|
| ||||
| OK | |
| 12.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
Confirm that the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition (Throttle Idle Position: ON) | Steady idling | Idling changes from steady to rough idling or engine stall |
| MAP (Data List) | MAP value is 20 to 40 kPa (150 to 300 mmHg) (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| Outside standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 13.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190 OR P3191) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON (IG) and turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC P3190 or P3191 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 15.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 16.CONFIRM WHETHER DTC MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Turn the Techstream on.
Clear the DTC (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON (IG) and turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P3190 or P3191.
Check the DTC judgment result.
| NEXT | ||
| ||