Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No.
DTC Detection Condition
Trouble Area
P0171
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
  1. Intake system
  2. Fuel injector assembly blockage
  3. Mass air flow meter sub-assembly
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor (sensor 1) circuit
  8. Air fuel ratio sensor (sensor 1)
  9. PCV valve and hose
  10. PCV hose connections
  11. EGR valve assembly
  12. Wire harness or connector
  13. ECM
P0172
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
  1. Fuel injector assembly leak or blockage
  2. Mass air flow meter sub-assembly
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor (sensor 1) circuit
  8. Air fuel ratio sensor (sensor 1)
  9. EGR valve assembly
  10. Wire harness or connector
  11. ECM

HINT:
  1. When DTC P0171 is stored, the actual air fuel ratio is on the lean side. When DTC P0172 is stored, the actual air fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 may be stored. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learned value is 35% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.

A121607E53


MONITOR STRATEGY


Required Sensors/Components
Air fuel ratio sensor
Mass air flow meter sub-assembly
Crank position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Fuel system status
Closed loop
Auxiliary battery voltage
11 V or higher
Either of the following conditions is met
1 or 2
1. Engine speed
Less than 1100 rpm
2. Engine load
10% or higher

TYPICAL MALFUNCTION THRESHOLDS


Fuel Trim 
Purge-cut
Executing
Either of the following conditions is met
1 or 2
1. Average between short-term fuel trim and long-term fuel trim
35% or higher (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim
-35% or less (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN


A263137E03

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG) and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the tester on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
  8. With the engine warmed up, idle the engine for 2 minutes or more [C].
  9. Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Enter the following menus: Powertrain / Engine and ECT / DTC [E].
  11. Read the pending DTCs.

    HINT:
    If a pending DTC is output, the system is malfunctioning.


WIRING DIAGRAM

Refer to DTC P0031 for the air fuel ratio sensor circuit .
Refer to DTC P0102 for the mass air flow meter sub-assembly circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  4. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  5. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC P0171 or P0172 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (Air fuel ratio)
    12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2
    (Heated oxygen)
    12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS Voltage B1S1
    Status
    O2S B1S2
    Air Fuel Ratio Condition and
    Air Fuel Ratio Sensor Condition
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    A
    Lean
    Lean
    Actual air fuel ratio lean
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector assembly blockage
    4. Gas leak from exhaust system
    5. Intake system
    6. Fuel pressure
    7. Mass air flow meter sub-assembly
    8. Engine coolant temperature sensor
    9. EGR valve assembly
    A
    Rich
    Rich
    Actual air fuel ratio rich
    1. Fuel injector assembly leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter sub-assembly
    6. Engine coolant temperature sensor
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    1. Air fuel ratio sensor
    2. EGR valve assembly
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    1. Air fuel ratio sensor
    B
    1. Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (Click here).



B
Go to step 11
A


5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    Tester Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, read the Data List after charging control has completed.


    Standard:

    Tester Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 3.0 gm/sec and 7.0 gm/sec



NG
Go to step 18
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    1. If the result of the spark test is normal, proceed to the next step.
    2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).
    3. Perform "Inspection After Repair" after repairing or replacing the ignition system (Click here).


NEXT


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the injection and volume.

    HINT:
    1. Refer to the fuel injector assembly inspection procedure (Click here).
    2. If the fuel injector assembly malfunction, engine misfire may occur. The misfire count can be read using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).
    3. Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)


    A217280E15
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C17-2 (+B) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)



NG
Go to step 23
OK


13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C17-1 (HA1A) - C10-23 (HA1A)
    Always
    Below 1 Ω
    C17-3 (A1A+) - C10-133 (A1A+)
    Always
    Below 1 Ω
    C17-4 (A1A-) - C10-134 (A1A-)
    Always
    Below 1 Ω
    C17-1 (HA1A) or C10-23 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C17-3 (A1A+) or C10-133 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C17-4 (A1A-) or C10-134 (A1A-) - Body ground
    Always
    10 kΩ or higher

    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C17-1 (HA1A) - C9-23 (HA1A)
    Always
    Below 1 Ω
    C17-3 (A1A+) - C9-133 (A1A+)
    Always
    Below 1 Ω
    C17-4 (A1A-) - C9-134 (A1A-)
    Always
    Below 1 Ω
    C17-1 (HA1A) or C9-23 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C17-3 (A1A+) or C9-133 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C17-4 (A1A-) or C9-134 (A1A-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.


Result 
Result
Proceed to
DTC P0171 or P0172 is output
A
DTC is not output
B


B
END
A


16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.

  1. Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

    NOTICE:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    MAP
    (Data List)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    1. While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
    2. Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

    Result:
    Result
    Proceed to
    Outside of standard range
    A
    Within standard range
    B



B
Go to step 18
A


17.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


19.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.


Result 
Result
Proceed to
DTC P0171 or P0172 is output
A
DTC is not output
B


B
END
A


20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C21-5 (VG) - C10-91 (VG)
    Always
    Below 1 Ω
    C21-4 (E2G) - C10-92 (E2G)
    Always
    Below 1 Ω
    C21-5 (VG) or C10-91 (VG) - Body ground
    Always
    10 kΩ or higher

    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C21-5 (VG) - C9-91 (VG)
    Always
    Below 1 Ω
    C21-4 (E2G) - C9-92 (E2G)
    Always
    Below 1 Ω
    C21-5 (VG) or C9-91 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly (Click here).

    HINT:
    1. If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).


NEXT


22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.


Result 
Result
Proceed to
DTC is not output
A
DTC P0171 or P0172 is output
B


B
REPLACE ECM (Click here)
A

END 

23.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C17-2 (+B) - 2C-4
    Always
    Below 1 Ω
    C17-2 (+B) or 2C-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)