DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
|
|
| P0301 P0302 P0303 P0304 | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
|
| Required Sensors/Components (Main) | Crank position sensor Cam position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature Intake air temperature sensor Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Intake air temperature | Higher than -10°C (14°F) |
| Either of the following conditions is met | A or B |
| A. Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| B. Engine coolant temperature | Higher than 20°C (68°F) |
| Duration | Crankshaft 1000 revolutions x 4 |
| Duration | Crankshaft 200 revolutions x 3 |
| Engine speed | Duration |
| Idling | 4.5 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (CYLINDER MISFIRE COUNT) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedures above [A].
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the tester [B].
| Result | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 5.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 6.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C10-20 (#10) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-17 (#20) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-18 (#30) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-19 (#40) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| C9-20 (#10) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C9-17 (#20) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C9-18 (#30) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C9-19 (#40) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | |
| 9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER |
Check the valve clearance .
|
| ||||
| OK | |
| 11.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 12.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
|
| ||||
| OK | |
| 14.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
| Tester Display | Condition | Specified Condition |
| MAF | Shift lever position: N A/C: Off Engine Speed: 2500 rpm | Between 3.0 gm/sec and 7.0 gm/sec |
|
| ||||
| OK | |
| 15.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assembly (Click here).
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.
| *1 | Timing Mark |
| *2 | Groove |
| *3 | No. 1 Cylinder TDC/Compression |
|
| ||||
| OK | |
| 16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| MAP (Data List) | (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| Outside of standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 17.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
|
| ||||
| 18.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 19.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 20.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
|
| ||||
| OK | |
| 21.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
| Tester Display | Condition | Specified Condition |
| MAF | Shift lever position: N A/C: Off Engine Speed: 2500 rpm | Between 3.0 gm/sec and 7.0 gm/sec |
|
| ||||
| OK | |
| 22.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assembly (Click here).
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.
| *1 | Timing Mark |
| *2 | Groove |
| *3 | No. 1 Cylinder TDC/Compression |
|
| ||||
| OK | |
| 23.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| MAP (Data List) | (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| Outside of standard range | A |
| Within standard range | B |
|
| ||||
| A | |
| 24.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 25.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 26.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 27.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 28.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY) |
![]() |
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C10-20 (#10) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-17 (#20) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-18 (#30) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-19 (#40) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| C9-20 (#10) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C9-17 (#20) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C9-18 (#30) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C9-19 (#40) - C9-51 (E01) | Power switch on (IG) | 11 to 14 V |
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | |
| 29.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 30.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER |
Check the valve clearance .
|
| ||||
| OK | |
| 31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).
| NEXT | |
| 32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 and/or P0304 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C21-5 (VG) - C10-91 (VG) | Always | Below 1 Ω |
| C21-4 (E2G) - C10-92 (E2G) | Always | Below 1 Ω |
| C21-5 (VG) or C10-91 (VG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| C21-5 (VG) - C9-91 (VG) | Always | Below 1 Ω |
| C21-4 (E2G) - C9-92 (E2G) | Always | Below 1 Ω |
| C21-5 (VG) or C9-91 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 34.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly (Click here).
| NEXT | |
| 35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 and/or P0304 is output) | B |
|
| ||||
| A | ||
| ||
| 36.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||