Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B282766E20


B392602E09


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  6. When replacing the door control and tire pressure monitoring system receiver assembly read the transmitter IDs (tire pressure warning system) stored in the old ECU using the intelligent tester and write them down before removal (Click here).*
  7. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the door control and tire pressure monitoring system receiver assembly if the door control receiver has been replaced.*
  8. Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution (Click here).
  9. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  10. The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".
  1. *: w/ Tire Pressure Warning System

1.INSPECT AUXILIARY BATTERY VOLTAGE
  1. Measure the voltage of the auxiliary battery with the power switch off.

    Standard Voltage:
    11 to 14 V

    HINT:
    It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

    1. If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


NEXT


2.CHECK FOR DTC
  1. Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.

  1. Connect the intelligent tester and check for DTCs (Click here).

    HINT:
    When using the intelligent tester with the vehicle power switch off, connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body / Entry&Start. While using the intelligent tester, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the intelligent tester and the vehicle.

    OK:
    DTCs are not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


3.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


4.CHECK KEY DIAGNOSTIC MODE


  1. Check the following antennas in the key diagnostic mode (Click here).

    HINT:
    If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference (w/ Tire Pressure Warning System).



      B431436E01
    1. Check the electrical key antenna (for driver door):
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.



    2. B431437E01
    3. Check the electrical key antenna (for front passenger door):
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.



    4. B431434E01
    5. Check the No. 3 indoor electrical key antenna (rear floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    6. B431432E01
    7. Check the No. 1 indoor electrical key antenna (front floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    8. B431433E01
    9. Check the No. 2 indoor electrical key antenna (steering column):
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    10. B431435E01
    11. Check the electrical key antenna (outside luggage):
      Text in Illustration 
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Result:
      Result
      Proceed to
      Diagnostic mode inspections fail for both channels (w/ Tire Pressure Warning System)
      A
      Diagnostic mode inspections fail (w/o Tire Pressure Warning System)
      Diagnostic mode inspections fail succeed for both channels (w/ Tire Pressure Warning System)
      B
      Diagnostic mode inspections fail succeed (w/o Tire Pressure Warning System)
      Diagnostic mode inspections fail succeed for only one of the channels (w/ Tire Pressure Warning System)
      C



B
Go to step 10

C
Go to step 21
A


5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
  1. Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.

    Result:
    Result
    Proceed to
    Another registered electrical key transmitter sub-assembly is not available
    A
    Another registered electrical key transmitter sub-assembly is available
    B



B
Go to step 7
A


6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
  1. Register a new electrical key transmitter sub-assembly.

    HINT:
    Refer to Service Bulletin.


NEXT


7.CHECK ENTRY DOOR LOCK OPERATION
  1. Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

    OK:
    Entry lock/unlock operate normally.



NG
Go to step 10
OK


8.CHECK TRANSMITTER BATTERY
  1. Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

    1. Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

      Result:
      Result
      Proceed to
      Transmitter LED does not illuminate when switch is pressed and held
      A
      Transmitter LED illuminates 3 times or more when switch is pressed and held
      B
      Transmitter LED illuminates once or twice but not a third time
      C

      HINT:
      1. The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (Click here).
      2. Even if the transmitter battery is depleted, it is still possible to start the hybrid system by holding the electrical key transmitter sub-assembly near the power switch, depressing the brake pedal and pressing the power switch.



B
REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C
REPLACE TRANSMITTER BATTERY (Click here)
A


9.INSPECT TRANSMITTER BATTERY (VOLTAGE)


  1. Inspect the transmitter battery.



      B431443E01
    1. Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (Click here).

    2. Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
      Text in Illustration 
      *A
      for Type A
      *B
      for Type B
      *1
      Lead Wire

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

    3. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    4. B431442E01
    5. Measure the voltage of the transmitter battery.

      HINT:
      1. When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.
      2. Perform the measurement when the key is at room temperature.
      3. The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes" (Click here).

      Text in Illustration 
      *A
      for Type A
      *B
      for Type B
      *1
      GND

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      Transmitter battery positive (+) - Transmitter battery negative (-)
      Power switch off, all doors closed and lock sensor touched
      2.3 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY 

10.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
    3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
    4. If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

    OK:
    Wireless and entry functions operate normally.

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Tire Pressure Warning System)
    B
    NG (w/o Tire Pressure Warning System)
    C



B
Go to step 11

C
Go to step 13
A

AFFECTED BY WAVE INTERFERENCE 

11.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Measure the voltage according to the value(s) in the table below.


    B264896E63


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    ALL OFF: Power switch off
    ACC ON: Power switch on (ACC) (ACC relay on)
    IG1 ON: Power switch on (IG) (IG1 relay on)
    IG2 ON: Power switch on (IG) (IG2 relay on)
    ST ON: Sending hybrid system start request signal
    Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

  1. Measure the voltage while checking the Data List on the intelligent tester.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G79-6 (IG1D) - Body ground
    Power switch off
    Below 1 V
    Power switch on (ACC)
    Below 1 V
    Power switch on (IG)
    9 V or higher
    G77-9 (IG2D) - Body ground
    Power switch off
    Below 1 V
    Power switch on (ACC)
    Below 1 V
    Power switch on (IG)
    9 V or higher
    G79-4 (ACCD) - Body ground
    Power switch off
    Below 1 V
    Power switch on (IG)
    9 V or higher
    Power switch on (ACC)
    9 V or higher

    HINT:
    Using the intelligent tester, measure the voltage while confirming the power source mode on the Data List.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


12.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry&Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    Power switch on (IG) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Displays whether the IG power source signal input is on or off.
    2. Use this Data List item to help determine the cause when all smart entry and start system/wireless functions do not operate.
    3. If the electrical key transmitter sub-assembly is brought inside the vehicle and the power switch is pressed twice without depressing the brake pedal, the power switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are compared, and the S code stored in the certification ECU (smart key ECU assembly) and the code stored in the ID code box (immobiliser code ECU) are compared, and if all codes match, the power source mode is considered on (IG) at that time.



NG
CHECK RELAY CONTACT SIDE CIRCUIT
OK


13.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Power switch status / ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    IG SW
    Power switch status / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -



NG
TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
OK


14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)


    B274828E16
  1. Disconnect the G77 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    G77-11 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    G77-10 (CUTB) - Body ground
    Power switch off
    11 to 14 V
    G77-2 (+B) - Body ground
    Power switch off
    11 to 14 V


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
  1. w/o Tire Pressure Warning System:

    1. Disconnect the G78 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the M15 door control receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      G78-5 (RCO) - M15-4 (+5)
      Always
      Below 1 Ω
      G78-17 (RDAS) - M15-5 (DATA)
      Always
      Below 1 Ω
      G78-19 (RSSI) - M15-2 (RSSI)
      Always
      Below 1 Ω
      G78-5 (RCO) or M15-4 (+5) - Body ground
      Always
      10 kΩ or higher
      G78-17 (RDAS) or M15-5 (DATA) - Body ground
      Always
      10 kΩ or higher
      G78-19 (RSSI) or M15-2 (RSSI) - Body ground
      Always
      10 kΩ or higher

  1. w/ Tire Pressure Warning System:

    1. Disconnect the G78 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the M48 door control receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Tester Connection
      Condition
      Specified Condition
      G78-5 (RCO) - M48-10 (+5)
      Always
      Below 1 Ω
      G78-17 (RDAM) - M48-9 (DATA)
      Always
      Below 1 Ω
      G78-6 (CSEL) - M48-6 (CSEL)
      Always
      Below 1 Ω
      G78-5 (RCO) or M48-10 (+5) - Body ground
      Always
      10 kΩ or higher
      G78-17 (RDAM) or M48-9 (DATA) - Body ground
      Always
      10 kΩ or higher
      G78-6 (CSEL) or M48-6 (CSEL) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK DOOR CONTROL RECEIVER


    B274837E26
  1. Connect the M15*1 or M48*2 door control receiver connector.

  1. Connect the G78 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    M15-1 (GND)*1 - Body ground
    Always
    Below 1 Ω
    M48-12 (GND)*2 - Body ground

    Text in Illustration 
    *A
    w/o Tire Pressure Warning System
    *B
    w/ Tire Pressure Warning System
    *a
    Component with harness connected
    (Door Control Receiver)
    1. *1: w/o Tire Pressure Warning System
    2. *2: w/ Tire Pressure Warning System

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/o Tire Pressure Warning System)
    B
    NG (w/ Tire Pressure Warning System)
    C



B
REPLACE DOOR CONTROL RECEIVER (Click here)

C
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
A


17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. w/o Tire Pressure Warning System:

    1. Connect the G78 certification ECU (smart key ECU assembly) connector.

    2. Connect the M15 door control receiver connector.



    3. B274836E79
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:

      Tester Connection
      Condition
      Specified Condition
      M15-4 (+5) - M15-1 (GND)
      Procedure:
      1. Power switch off
      2. Electrical key transmitter sub-assembly switch not pressed
      Below 1 V
      Procedure:
      1. Power switch off
      2. Electrical key transmitter sub-assembly switch pressed
      4.5 to 5.5 V

      Text in Illustration 
      *a
      Component with harness connected
      (Door Control Receiver)



  1. w/ Tire Pressure Warning System:

    1. Connect the G78 certification ECU (smart key ECU assembly) connector.

    2. Connect the M48 door control receiver connector.



    3. B389376E06
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:

      Tester Connection
      Condition
      Specified Condition
      M48-10 (+5) - M48-12 (GND)
      Procedure:
      1. Power switch off
      2. Electrical key transmitter sub-assembly switch not pressed
      Below 1 V
      Procedure:
      1. Power switch off
      2. Electrical key transmitter sub-assembly switch pressed
      4.5 to 5.5 V
      M48-6 (CSEL) - M48-12 (GND)
      Power switch off and all doors closed
      Below 1 V → Pulse generation
      M48-1 (IG) - M48-12 (GND)
      Power switch on (IG)
      10 to 16 V
      M48-7 (+B) - M48-12 (GND)
      Always
      10 to 16 V

      Text in Illustration 
      *a
      Component with harness connected
      (Door Control Receiver)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


18.CHECK DOOR CONTROL RECEIVER


  1. w/o Tire Pressure Warning System:

    1. Connect the G78 certification ECU (smart key ECU assembly) connector.

    2. Connect the M15 door control receiver connector.



    3. B274836E81
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:

      Tester Connection
      Condition
      Specified Condition
      M15-5 (DATA) - M15-1 (GND)
      Procedure:
      1. All doors closed
      2. All doors locked
      3. Electrical key transmitter sub-assembly switch pressed
      Below 2 V → 11 to 14 V → Below 2 V
      M15-2 (RSSI) - M15-1 (GND)
      Procedure:
      1. All door closed
      2. All door locked
      3. Electrical key transmitter sub-assembly switch pressed
      11 to 14 V → Below 2 V

      Text in Illustration 
      *a
      Component with harness connected
      (Door Control Receiver)



  1. w/ Tire Pressure Warning System:

    1. Connect the G78 certification ECU (smart key ECU assembly) connector.

    2. Connect the M48 door control receiver connector.



    3. B389376E07
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:

      Tester Connection
      Condition
      Specified Condition
      M48-9 (DATA) - M48-12 (GND)
      Procedure:
      1. All doors closed
      2. All doors locked
      3. Electrical key transmitter sub-assembly switch pressed
      Below 1 V → 10 to 16 V → Below 1 V
      M48-6 (CSEL) - M48-12 (GND)
      Procedure:
      1. Power switch off
      2. All doors closed
      Below 1 V → Pulse generation

      Text in Illustration 
      *a
      Component with harness connected
      (Door Control Receiver)

      Result:
      Result
      Proceed to
      OK
      A
      NG (w/o Tire Pressure Warning System)
      B
      NG (w/ Tire Pressure Warning System)
      C



B
REPLACE DOOR CONTROL RECEIVER (Click here)

C
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
A


19.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


20.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check that the wireless door lock functions operate normally (Click here).

    OK:
    Wireless door lock functions operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) 

21.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode (Click here).

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
    3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
    4. If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

    OK:
    Wireless door lock buzzer sounds.



NG
Go to step 22
OK

AFFECTED BY WAVE INTERFERENCE 

22.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
  1. Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.

    Result:
    Result
    Proceed to
    Another registered electrical key transmitter sub-assembly is not available
    A
    Another registered electrical key transmitter sub-assembly is available
    B



B
Go to step 24
A


23.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
  1. Register a new electrical key transmitter sub-assembly.

HINT:
Refer to Service Bulletin.


NEXT


24.CHECK KEY DIAGNOSTIC MODE
  1. Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode (Click here).

    OK:
    Wireless door lock buzzer sounds.



NG
Go to step 25
OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY THAT WAS INSPECTED FIRST WAS DEFECTIVE) 

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY)
  1. Disconnect the G78 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the M48 door control and tire pressure monitoring system receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    G78-6 (CSEL) - M48-6 (CSEL)
    Always
    Below 1 Ω
    G78-6 (CSEL) or M48-6 (CSEL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Connect the G78 certification ECU (smart key ECU assembly) connector.

  1. Connect the M48 door control and tire pressure monitoring system receiver assembly connector.



    B389376E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    M48-6 (CSEL) - M48-12 (GND)
    Power switch off and all doors closed
    Below 1 V → Pulse generation

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control and Tire Pressure Monitoring System Receiver Assembly)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


27.CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY
  1. Connect the G78 certification ECU (smart key ECU assembly) connector.

  1. Connect the M48 door control and tire pressure monitoring system receiver assembly connector.



    B389376E04
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    M48-9 (DATA) - M48-12 (GND)
    Procedure:
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch pressed*
    Below 1 V → 10 to 16 V → Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control and Tire Pressure Monitoring System Receiver Assembly)
    1. *: While the electrical key antennas are being inspected in key diagnostic mode (Click here).



NG
REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)
OK


28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


29.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check that the wireless door lock functions operate normally (Click here).

    OK:
    Wireless door lock functions operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)