The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.
*1: When performing learning using the GTS.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION
1. PRECAUTION
Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.
Make sure to perform initialization after replacing the air conditioning radiator damper servo sub-assembly. If initialization is not performed, the air conditioner unit assembly will not perform properly as the air conditioning amplifier assembly will not be able to recognize the position of the air conditioning radiator damper sub-assembly.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55737B
4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)
55738D
5.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)
55735A
6.REMOVE WATER GUARD PLATE LH
55736D
7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
87246A
9.DISCONNECT OUTLET HEATER WATER HOSE A (w/o Exhaust Heat Recirculation System)
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.
Do not apply excessive force to the outlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
87207A
10.DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY A (w/ Exhaust Heat Recirculation System)
Using pliers, grip the claws of the clip and slide the clip to disconnect the water pipe and hose sub-assembly A.
Do not apply excessive force to the water pipe and hose sub-assembly A.
Prepare a drain pan or cloth in case the coolant leaks.
87245A
11.DISCONNECT INLET HEATER WATER HOSE A
w/o Exhaust Heat Recirculation System:
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.
Do not apply excessive force to the inlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
w/ Exhaust Heat Recirculation System:
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.
Do not apply excessive force to the inlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
88707
12.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
13.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Disconnect the air conditioner tube and accessory assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
14.REMOVE FRONT SEAT ASSEMBLY LH
for Manual seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
15.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
16.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
17.REMOVE STEERING COLUMN ASSEMBLY
86652F
18.REMOVE SKID CONTROL BUZZER (w/ Toyota Safety Sense P)
88150A
19.REMOVE DRIVING SUPPORT ECU ASSEMBLY (w/ Toyota Safety Sense P)
85940
20.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)
89343C
21.REMOVE NO. 1 CLEARANCE WARNING BUZZER (w/ TOYOTA Parking Assist-sensor System)
89343D
22.REMOVE NO. 2 CLEARANCE WARNING BUZZER (w/ TOYOTA Parking Assist-sensor System)
89340A
23.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
85970A
24.REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)
82877
25.REMOVE ECU INTEGRATION BOX RH (for LHD)
82878
26.REMOVE ECU INTEGRATION BOX LH (for RHD)
33560
27.REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY
88625Q
28.REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR
Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.
58816C
29.REMOVE FRONT NO. 1 CONSOLE BOX INSERT
|
Place Hand Here |
|
Remove in this Direction |
Disengage the clip and claw as shown in the illustration.
|
Remove in this Direction |
Disengage the guide to remove the front No. 1 console box insert as shown in the illustration.
58817B
30.REMOVE FRONT NO. 2 CONSOLE BOX INSERT
|
Place Hand Here |
|
Remove in this Direction |
Disengage the clip and claw as shown in the illustration.
|
Remove in this Direction |
Disengage the guide to remove the front No. 2 console box insert as shown in the illustration.
58569D
31.REMOVE FRONT FLOOR CAUTION PLATE COVER
|
Place Hand Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claw and guide as shown by the arrow (1), and then pull the front floor caution plate cover as shown by the arrow (2) in the illustration to remove it.
87212G
32.REMOVE REAR NO. 3 AIR DUCT
Remove the 2 front floor carpet clips.
Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws to remove the rear No. 3 air duct as shown in the illustration.
87212F
33.REMOVE REAR NO. 2 AIR DUCT
Disengage the 2 claws and remove the rear No. 2 air duct.
87212J
34.REMOVE REAR NO. 5 AIR DUCT
Remove the 2 front floor carpet clips.
Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.
|
Remove in this Direction |
Disengage the 2 claws to remove the rear No. 5 air duct as shown in the illustration.
87212H
35.REMOVE REAR NO. 4 AIR DUCT
Disengage the 2 claws and remove the rear No. 4 air duct.
87212
36.REMOVE REAR NO. 1 AIR DUCT
Disengage the 4 claws to remove the rear No. 1 air duct.
55215D
37.REMOVE NO. 3 DASH PANEL INSULATOR PAD
Disengage the 2 clips to remove the No. 3 dash panel insulator pad.
55306A
38.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Turn back the front floor mat as shown in the illustration.
Disengage each clamp.
Remove the bolt and disconnect the earth wire.
w/ PTC Heater:
Remove the bolt and disconnect the earth wire.
|
Bolt |
|
Screw |
|
Nut |
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
55307C
39.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Turn back the front floor mat as shown in the illustration.
Disengage each clamp.
|
Bolt |
|
Screw |
|
Nut |
Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.
55308B
40.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
for LHD:
|
Bolt |
|
Nut |
Disengage the clamp and 2 claws to disconnect the DLC3 connector.
Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.
41.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
55990B
42.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
Disengage the 6 claws to remove the lower defroster nozzle assembly.
43.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
for LHD:
Disconnect each connector.
| *A | w/ PTC Heater | - | - |
| *a | Earth Wire | *b | Relay Block Assembly |
|
Connector |
|
Bolt |
Remove the 3 bolts and disconnect the 3 earth wires.
Remove the bolt and disconnect the relay block assembly.
Disengage each clamp and disconnect the instrument panel wire.
for RHD:
Disconnect each connector.
| *a | Earth Wire | *b | Relay Block Assembly |
|
Connector |
|
Bolt |
Remove the 3 bolts and disconnect the 3 earth wires.
Remove the bolt and disconnect the relay block assembly.
Disengage each clamp and disconnect the instrument panel wire.
| *1 | COOLER UNIT DRAIN HOSE GROMMET |
Disconnect the drain cooler hose.
If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.
Remove the 2 bolts.
Remove the 4 bolts (A).
|
Bolt (A) |
|
Bolt (B) |
|
Nut | - | - |
Remove the bolt (B) and disconnect the parking brake pedal assembly.
Remove the nut.
Disconnect each connector.
|
Remove in this Direction | - | - |
Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
44.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.