Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat)
RM3210E _58 Vehicle Interior _047549 SEAT _0234654 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 72211C 1.INSTALL SEAT TRACK ADJUSTING HANDLE

a.
B439694

Engage the 2 claws to install the seat track adjusting handle to the front seat adjuster assembly.


Hide 71052A 2.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY

a.
B439693

Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.


Hide 7181B 3.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER

a.
B439692

Engage the claw to install the front seat cushion wire harness holder.


b.

Install the 2 screws.


Hide 82191 4.INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)

a.

w/ Occupant Classification System:

i.

Connect each connector and engage each clamp to install the front seat wire RH.



Hide 82192B 5.INSTALL FRONT SEAT NO. 2 WIRE LH (for Driver Side)

a.
B432143

w/ Airbag Cut Off Switch:

i.

Engage the claw.


ii.

Engage the clamp to install the front seat No. 2 wire LH.



Hide 82192 6.INSTALL FRONT SEAT WIRE LH (for Driver Side)

a.

w/ Lumbar Support:

i.

Connect each connector and engage each clamp to install the front seat wire LH.



Hide 71875G 7.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Driver Side)

a.
B439759

Engage the 4 claws to install the LH seat reclining adjuster inside cover LH.


b.
B439760

w/ Lumbar Support:

i.

Engage the claw.



Hide 71876G 8.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Driver Side)

a.
B439691

Engage the 4 claws to install the LH seat reclining adjuster inside cover RH.


Hide 71875F 9.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Front Passenger Side)

a.
B431139

Engage the 4 claws to install the RH seat reclining adjuster inside cover LH.


b.
B432144

w/ Occupant Classification System:

i.

Engage the clamp.



Hide 71876F 10.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Front Passenger Side)

a.
B431140

Engage the 4 claws to install the RH seat reclining adjuster inside cover RH.


Hide 71874A 11.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

a.
B439688C01
2.573,0.542 3.073,0.542 true 1.979,1.333 2.948,1.333 false 3.073,0.458 3.385,0.615 0.313,0.156 10 true *a 2.969,1.25 3.281,1.406 0.313,0.156 10 false *b
*a Hook
*b Guide


Engage the claw and guide.


b.

Engage the hook to install the front seat lower cushion shield LH.


Hide 71874A 12.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

a.
B439689C01
2.083,1.573 2.948,1.573 false 2.5,0.698 3.104,0.698 true 3.125,0.615 3.333,0.802 0.208,0.188 10 false *a 2.979,1.49 3.292,1.646 0.313,0.156 10 false *b
*a Hook
*b Guide


Engage the claw and guide.


b.

Engage the hook to install the front seat lower cushion shield RH.


Hide 739F0 13.INSTALL FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (for Front Passenger Side)

Hide 87510L 14.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71072S 15.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.
B431153

Engage the 13 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.


Hide 16.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Engage the 10 hooks to install the separate type front seat cushion cover with pad.

B439687


b.
B439686

Engage the 2 hooks.


c.

w/ Seat Heater System:

i.
B439685

Engage the claw and 4 clamps to install the front seat cushion heater assembly wire harness.

HINT:

Engage the claw first.




Hide 8219B 17.INSTALL FRONT SEAT NO. 2 WIRE (w/ Lumbar Support)

a.
B432141

Engage the clamp to install the front seat No. 2 wire.


Hide 71759B 18.INSTALL FRONT SEATBACK HOOK

a.
B429312

Install the 2 front seatback hooks to the front seatback frame sub-assembly.


Hide 71587 19.INSTALL FRONT SEATBACK EDGE PROTECTOR (w/o Lumbar Support)

a.

Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.


Hide 71587 20.INSTALL FRONT SEATBACK EDGE PROTECTOR (w/ Lumbar Support)

a.

Install the 2 front seatback edge protectors to the lumbar support adjuster assembly.


Hide 71054S 21.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)

a.
B439695C01
0,0 0,0 false
V113147

Install in this direction


Install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.


b.
B439683

Engage the 2 claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.


Hide 72760D 22.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)

Hide 87510N 24.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71074S 25.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.
B439682

Engage the 17 claws to install the separate type front seatback cover to the separate type front seatback pad.


Hide 26.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.

Install the separate type front seatback cover with pad.


Hide 71931 27.INSTALL FRONT SEAT HEADREST SUPPORT

a.
B429323

Engage the 4 claws to install the 2 front seat headrest supports.


b.
B429322

Close the 2 fasteners.


c.

w/ Seat Heater System:

i.
B439681

Engage the clamp.



d.
B432139

Engage the 3 hooks.


Hide 28.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B439679

Engage the 4 guides.


b.

Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B432138

Engage the claw and 4 clamps to install the front seat airbag assembly wire harness.

HINT:

Engage the claw first.



d.

w/ Seat Heater System:

i.
B439677

Engage the clamp.


ii.

Connect the connector.



e.

w/ Lumbar Support:

i.
B432137

Engage the clamp.


ii.

Connect the connector.



f.
B439676

Engage the 2 hooks.


Hide 72497B 29.INSTALL VERTICAL ADJUSTER BRACKET COVER (for Driver Side)

a.
B439675

Engage the claw to install the vertical adjuster bracket cover.


Hide 71862 30.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)

a.
B439696C01
0,0 0,0 false
V113147

Install in this direction


Engage the 2 claws and 2 guides as shown in the illustration.


b.
B439673

Engage the 2 claws to install the front seat inner cushion shield.


Hide 84922A 31.INSTALL FRONT LUMBAR POWER SEAT SWITCH (w/ Lumbar Support)

Hide 71812D 32.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)

a.
B432136

w/ Lumbar Support:

i.

Connect the front lumbar power seat switch connector.


ii.

Engage the 2 clamps.



b.
B439697C01
0.281,1.448 0.885,1.448 true 1.74,0.344 2.656,0.344 true 2.083,0.344 2.083,0.656 2.083,0.656 2.417,0.656 true 0.146,1.375 0.302,1.573 0.156,0.198 10 true A 1.604,0.271 1.76,0.469 0.156,0.198 10 true B
V113147

Install in this direction (1)
V113148

Install in this direction (2)


Engage the guide (A) as shown in the illustration.


c.

Engage the 3 claws and 2 guides (B) as shown in the illustration.


d.
B439670

Engage the 2 claws to install the front seat cushion shield.


Hide 71849 33.INSTALL SEAT ADJUSTER COVER CAP (for Driver Side)

a.
B439699C01
0,0 0,0 false
V113147

Install in this direction (1)
V113148

Install in this direction (2)


Engage the 2 guides as shown in the illustration.


b.

Engage the 2 claws to install the seat adjuster cover cap as shown in the illustration.


Hide 71861 34.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)

a.
B431138C01
0,0 0,0 false
V113147

Install in this direction


Engage the 2 claws and 2 guides as shown in the illustration.


b.
B431135

Engage the 3 claws to install the front seat inner cushion shield.


Hide 71811D 35.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)

a.
B431134C01
0.771,0.344 1.813,0.344 true 1.021,0.656 1.438,0.656 1.438,0.656 1.438,0.354 true 2.531,1.448 3.156,1.448 true 3.208,1.365 3.365,1.563 0.156,0.198 10 true A 1.833,0.271 1.99,0.469 0.156,0.198 10 true B
V113147

Install in this direction (1)
V113148

Install in this direction (2)


Engage the guide (A) as shown in the illustration.


b.

Engage the 2 claws and 2 guides (B) as shown in the illustration.


c.
B431129

Engage the 2 claws to install the front seat cushion shield.


Hide 72526A 36.INSTALL RECLINING ADJUSTER RELEASE HANDLE

a.
B439668

Install the reclining adjuster release handle.


Hide 72551 37.INSTALL NO. 1 RECLINING HINGE COVER

a.
B439700

Engage the guide.


b.

Engage the claw to install the No. 1 reclining hinge cover.


Hide 72495 38.INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)

a.
B439701C02
0,0 0,0 false
V113147

Install in this direction


Engage the claw to install the vertical adjusting handle as shown in the illustration.


Hide 71074S 39.CONNECT SEPARATE TYPE FRONT SEATBACK COVER

a.
B439665

Connect the rubber band of the separate type front seatback cover.


Hide 73240 40.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

Hide 73230 41.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

Hide 89952 42.INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side)

Hide 89178A 43.INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

Hide 72277A 44.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)