Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Display Malfunction  


DESCRIPTION

FUEL RECEIVER GAUGE OPERATION


a.

OPERATION

The combination meter assembly (meter circuit plate) uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly (meter circuit plate) detects the voltage output from the fuel sender gauge assembly and operates the fuel receiver gauge.



FUEL RECEIVER GAUGE READING


a.

During normal driving:

As the fuel level in the fuel tank assembly changes when driving on a hill or applying the brakes, the fuel receiver gauge reading is updated according to the fuel injection volume during normal driving. However, as the fuel injection volume measurement has a margin of error, the value is indicated after correction by input values from the fuel sender gauge assembly.


b.

During refueling:

The fuel level in the fuel tank assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the changes in the fuel level, output values from the fuel sender gauge assembly is immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



REFUELING JUDGMENT CONDITIONS


NOTICE:

Add fuel with the power switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading will be obtained.


a.

Normal judgment condition (When normal refueling method is used)

With the power switch off, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.


b.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the power switch on (IG) or on (READY), the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the power switch is on (READY), the fuel sender gauge assembly detects a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level.




PRECAUTION FOR REFUELING


a.

The fuel sender gauge assembly cannot detect changes in the fuel level within certain ranges (around points E and F). Therefore, even if 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


b.

The fuel sender gauge reading takes approximately 1 minute to rise from point E to F. If the vehicle is driven while the fuel sender gauge reading is rising, the fuel sender gauge reading will stop rising. After the fuel sender gauge reading stops rising, normal fuel sender gauge reading operation begins. The fuel sender gauge reading takes approximately 1.6 minutes per 1 liter (1.1 US qts, 0.9 Imp. qts) to rise while the vehicle is being driven, and takes approximately 5 minutes per 1 liter (1.1 US qts, 0.9 Imp. qts) to rise while the vehicle is stopped.



FORCED RESET OF FUEL RECEIVER GAUGE


When driving at a vehicle speed of 1.8 km/h (1 mph) or more, if the output value from the fuel sender gauge assembly is different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 5 minutes, the output value from the fuel sender gauge assembly is immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.


PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL (w/ Canister Pump Module)


a.

Disconnect and reconnect the cable to the negative (-) auxiliary battery terminal and then open and close the fuel lid before turning the power switch on (IG) to increase the accuracy of the fuel receiver gauge.

HINT:

w/ Canister Pump Module: The accuracy of the fuel receiver gauge changes depending on fuel tank deformation caused by internal pressure. Before turning the power switch on (IG), equalizing the fuel tank pressure with the ambient air pressure by opening and closing the fuel lid after disconnecting and reconnecting the cable to the negative (-) auxiliary battery terminal increases the accuracy of the fuel receiver gauge.




WIRING DIAGRAM

E285369E06
0.115,2.646 0.448,2.813 0.333,0.167 10 false M10 0.115,2.813 3.865,3.219 3.75,0.406 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.208,2.625 5.583,2.833 0.375,0.208 10 false F6 5.208,2.792 7.021,3.344 1.813,0.552 10 false Combination Meter Assembly (Meter Circuit Plate) 0.781,1.479 1.25,1.667 0.469,0.188 10 false Sender 1.688,1.188 1.833,1.354 0.146,0.167 10 false 1 1.688,1.844 1.833,2.01 0.146,0.167 10 false 2 2.333,0.74 2.479,0.906 0.146,0.167 10 false 3 2.333,1.406 2.479,1.573 0.146,0.167 10 false 1 2.323,2.083 2.469,2.25 0.146,0.167 10 false 2 2.021,2.083 2.271,2.25 0.25,0.167 10 false FE 2.042,1.406 2.292,1.573 0.25,0.167 10 false FV 2.031,0.74 2.688,1.021 0.656,0.281 10 false FR 5.458,0.74 5.708,0.906 0.25,0.167 10 false 29 5.469,1.406 5.719,1.573 0.25,0.167 10 false 31 5.469,2.083 5.719,2.25 0.25,0.167 10 false 30 5.74,0.833 6.156,1.135 0.417,0.302 10 false FR 5.74,1.5 5.99,1.667 0.25,0.167 10 false FV 5.75,2.208 6.188,2.448 0.438,0.24 10 false FE&B 0.802,1.313 1.115,1.49 0.313,0.177 10 false Fuel 0.781,1.646 1.229,1.854 0.448,0.208 10 false Gauge 0.781,1.813 1.417,2 0.635,0.188 10 false Assembly 1.813,1.396 1.958,1.563 0.146,0.167 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Disconnect and reconnect the cable to the negative (-) auxiliary battery terminal and then open and close the fuel lid before turning the power switch on (IG) to increase the accuracy of the fuel receiver gauge (w/ Canister Pump Module).

w/ Canister Pump Module: The accuracy of the fuel receiver gauge changes depending on fuel tank deformation caused by internal pressure. Before turning the power switch on (IG), equalizing the fuel tank pressure with the ambient air pressure by opening and closing the fuel lid after disconnecting and reconnecting the cable to the negative (-) auxiliary battery terminal increases the accuracy of the fuel receiver gauge.


HINT:

The fuel level warning light will come on when the fuel level is below 6.4 liters (6.8 US qts, 5.6 Imp. qts).


PROCEDURE

1.CHECK SYMPTOMS
a.

Ask the customer about the problem symptoms.


Result:
Result Proceed to
Malfunction occurs when adding fuel (Even after adding fuel, reading does not increase at all or increases very slowly, etc.) A
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) B
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) C



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

13.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

C

18.CHECK FOR DTC
2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

3.CHECK FOR DTC
a.

Check if SFI system DTCs are output.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



A

4.CHECK FOR DTC

B

4.CHECK FOR DTC
a.

Check if electronically controlled brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output. A
Electronically controlled brake system DTCs are output. B



A

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

B

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
a.

Record the fuel receiver gauge reading.


b.

If the fuel tank assembly is almost full, drain 20 liters or more of fuel. (This is not necessary when the fuel tank assembly is sufficiently below full.)


c.

Disconnect the cable from the negative (-) auxiliary battery terminal to reset the fuel receiver gauge.

HINT:

Check that the power switch is turned off before disconnecting the cable from the negative (-) auxiliary battery terminal.



d.

Connect the cable to the negative (-) auxiliary battery terminal and turn the power switch on (IG).

NOTICE:

Disconnect and reconnect the cable to the negative (-) auxiliary battery terminal and then open and close the fuel lid before turning the power switch on (IG) to increase the accuracy of the fuel receiver gauge (w/ Canister Pump Module).



e.

Check that the fuel receiver gauge has been reset.


f.

Drive the vehicle at 1.75 km/h or more, then park (P) is selected and turn the power switch off.


g.

Add 5.0 liters or more of fuel, turn the power switch on (IG), and check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.


Result:
Result Proceed to
Fuel receiver gauge reading increases in proportion to the amount of fuel added A
Fuel receiver gauge reading does not change even when fuel is added B



A

6.INSPECT FUEL TANK ASSEMBLY

B

7.READ VALUE USING GTS (FUEL INPUT)
6.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal. B
There is an excessive amount of foreign matter in the fuel tank assembly. C
The fuel tank assembly or fuel sender gauge assembly is not installed correctly. D



A

7.READ VALUE USING GTS (FUEL INPUT)

B

C

CLEAN INSIDE OF FUEL TANK ASSEMBLY

D

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY

7.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L w/ Canister Pump Module:
Fuel receiver gauge indicates F (1/1): 38.3 L
Fuel receiver gauge indicates 3/4: 29.8 L
Fuel receiver gauge indicates 1/2: 21.3 L
Fuel receiver gauge indicates 1/4: 12.8 L
Fuel receiver gauge indicates E (R): 4.3 L
w/o Canister Pump Module:
Fuel receiver gauge indicates F (1/1): 38.3 L
Fuel receiver gauge indicates 3/4: 29.9 L
Fuel receiver gauge indicates 1/2: 21.4 L
Fuel receiver gauge indicates 1/4: 12.8 L
Fuel receiver gauge indicates E (R): 4.3 L
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication. A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. B



A

8.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)

B

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

8.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
a.
E284677C16
1.5,0.208 1.906,0.458 0.406,0.25 1.271,1.635 1.667,1.083 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.625,0.25 1.927,0.479 0.302,0.229 10 false F6 1.146,1.708 1.458,1.865 0.313,0.156 10 false FV
*a Component with harness connected
(Combination Meter Assembly (Meter Circuit Plate))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-31 (FV) - Body ground Power switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

9.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E284677C15
1.5,0.208 1.906,0.458 0.406,0.25 1.875,1.115 2.208,1.698 true 1.76,1.125 1.292,1.708 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.635,0.25 1.979,0.479 0.344,0.229 10 false F6 1.042,1.75 1.552,1.958 0.51,0.208 10 false FE&B 2.146,1.75 2.458,1.906 0.313,0.156 10 false FR
*a Component with harness connected
(Combination Meter Assembly (Meter Circuit Plate))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F6-29 (FR) - F6-30 (FE&B) Power switch on (IG) 0.3 to 4.6 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Disconnect the M10 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-29 (FR) - M10-3 (FR) Always Below 1 Ω
F6-30 (FE&B) - M10-2 (FE) Always Below 1 Ω
F6-31 (FV) - M10-1 (FV) Always Below 1 Ω
F6-29 (FR) or M10-3 (FR) - Body ground Always 10 kΩ or higher
F6-30 (FE&B) or M10-2 (FE) - Body ground Always 10 kΩ or higher
F6-31 (FV) or M10-1 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FUEL SENDER GAUGE ASSEMBLY

b.

Inspect the fuel sender gauge assembly.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY(w/ Canister Pump Module)>INSPECTION

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY(w/o Canister Pump Module)>INSPECTION

OK:

Fuel sender gauge assembly is normal.



Result:
Proceed to
OK
NG



OK

12.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

12.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.
E158805C05
0.313,1.333 0.74,1.635 0.427,0.302 0.313,3.667 0.729,3.958 0.417,0.292 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.5,1.417 0.833,1.667 0.333,0.25 10 false A 0.5,3.74 0.833,3.99 0.333,0.25 10 false B
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

13.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

14.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

14.CHECK FOR DTC
a.

Check if SFI system DTCs are output.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



A

15.CHECK FOR DTC

B

15.CHECK FOR DTC
a.

Check if electronically controlled brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output. A
Electronically controlled brake system DTCs are output. B



A

16.CHECK FOR DTC

B

16.CHECK FOR DTC
a.

Check if meter / gauge system DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTC B1500 is not output. A
DTC B1500 is output. B



A

17.INSPECT FUEL RECEIVER GAUGE

B

17.INSPECT FUEL RECEIVER GAUGE
a.

Disconnect the cable from the negative (-) auxiliary battery terminal to reset the fuel receiver gauge.

HINT:

Check that the power switch is turned off before disconnecting the cable from the negative (-) auxiliary battery terminal.



b.

Connect the cable to the negative (-) auxiliary battery terminal and turn the power switch on (IG).

NOTICE:

Disconnect and reconnect the cable to the negative (-) auxiliary battery terminal and then open and close the fuel lid before turning the power switch on (IG) to increase the accuracy of the fuel receiver gauge (w/ Canister Pump Module).



c.

Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly.


Result:
Result Proceed to
Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly. A
Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank assembly. B



A

END

B

7.READ VALUE USING GTS (FUEL INPUT)
18.CHECK FOR DTC
a.

Check if SFI system DTCs are output.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



A

19.CHECK FOR DTC

B

19.CHECK FOR DTC
a.

Check if electronically controlled brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output. A
Electronically controlled brake system DTCs are output. B



A

20.INSPECT FUEL TANK ASSEMBLY

B

20.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal. B
There is an excessive amount of foreign matter in the fuel tank assembly. C
The fuel tank assembly or fuel sender gauge assembly is not installed correctly. D



A

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

B

C

CLEAN INSIDE OF FUEL TANK ASSEMBLY

D

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY