Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0242212 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Circuit

·

IG Relay Monitor (Outside)

·

IG Relay Monitor (Inside)



CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A and 3D instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-17 (IG1D) - 3A-17 Always Below 1 Ω
3D-3 - Body ground Always Below 1 Ω
F1-17 (IG1D) or 3A-17 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the 1A No. 1 integration relay connector.


b.

Disconnect the 3F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-12 - 1A-2 Always Below 1 Ω
3F-12 or 1A-2 - Body ground Always 10 kΩ or higher
3F-13 - 1A-7 Always Below 1 Ω
3F-13 or 1A-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B424435C07
1.906,1.49 2.323,1.74 0.417,0.25 5.458,0.156 5.875,0.406 0.417,0.25 2.385,0.083 2.802,0.333 0.417,0.25 5.271,1.49 5.688,1.74 0.417,0.25 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 2.51,0.115 2.823,0.354 0.313,0.24 10 false 3A 2.031,1.521 2.365,1.813 0.333,0.292 10 false 3H 5.583,0.188 5.906,0.396 0.323,0.208 10 false 3K 5.396,1.521 5.719,1.771 0.323,0.25 10 false 3D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-17 - 3D-3 20°C (68°F) 130.92 to 190.69 Ω
3K-1 - 3A-35 Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 Below 1 Ω
Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 10 kΩ or higher
3K-1 - 3H-12 Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 Below 1 Ω
Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1, IG1 NO. 3 RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1, IG1 NO. 3 RELAY)
a.

Remove the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Inspect the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2 NO. 1, IG1 NO. 3 RELAY)

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Install the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


c.

Install the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSTALLATION


d.
B424427C19
1.542,0.083 1.958,0.333 0.417,0.25 1.344,1.958 1.177,1.958 1.177,1.958 1.177,0.958 false 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.698,0.146 2.01,0.302 0.313,0.156 10 false F1 1.365,1.896 1.865,2.135 0.5,0.24 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F1-17 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)