Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(for LHD)
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0243381 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not apply excessive force to the brake lines or refrigerant lines.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 47070 2.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C346799C01
0.51,2.656 0.719,2.656 false 0.896,3.156 0.896,2.99 false 2.865,0.802 2.969,0.802 2.969,0.802 2.969,1.01 false 2.833,0.219 2.688,0.219 2.688,0.219 2.688,0.417 false 0.365,2.573 0.677,2.729 0.313,0.156 10 false *1 2.854,0.135 3.167,0.292 0.313,0.156 10 false *2 2.917,1.01 3.229,1.167 0.313,0.156 10 false *3 0.833,3.156 1.146,3.313 0.313,0.156 10 false *2
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing
*3 Brake Actuator Case Collar
V113147

Install in this Direction


Install the brake booster pump assembly to the brake actuator bracket assembly with the nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Be careful not to allow any brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the brake booster pump bushing and brake actuator case collar are on the brake actuator bracket assembly, and 2 brake booster pump bushings and 2 brake booster pump collars are on the brake booster pump assembly.

·

Do not drop the brake booster pump assembly when carrying it.




b.

Engage the claw and clamp to install the brake booster pump assembly wire harness to the brake actuator bracket assembly.


Hide 473A1 3.INSTALL ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.

Temporarily tighten the accumulator to brake master cylinder tube to the brake booster pump assembly.


b.
C346796C01
2.885,2.885 2.729,2.885 2.729,2.885 2.729,2.635 false 1.802,2.927 2.115,3.083 0.313,0.156 10 false *a 2.917,2.813 3.229,2.969 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Install the accumulator to brake master cylinder tube with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Using a union nut wrench, tighten the accumulator to brake master cylinder tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.38 N*m (136 kgf*cm, 10 ft.*lbf)




Hide 4.CONNECT BRAKE LINE

a.
C347180C01
1.573,1.688 1.573,1.396 true 2.01,0.906 2.208,0.708 2.208,0.708 2.448,0.708 true 1.698,0.656 2,0.219 2,0.219 2.208,0.219 true 1.531,0.813 1.229,0.229 1.229,0.229 0.969,0.229 true 1.365,0.958 0.865,0.573 0.865,0.573 0.646,0.573 true 0.833,1.375 1.073,1.375 1.073,1.375 1.229,1.135 true 1.5,1.688 1.677,1.865 0.177,0.177 10 true *a 2.458,0.625 2.646,0.792 0.188,0.167 10 true *b 0.667,1.292 0.844,1.469 0.177,0.177 10 true *c 0.458,0.49 0.646,0.667 0.188,0.177 10 true *d 0.792,0.146 0.969,0.333 0.177,0.188 10 true *e 2.229,0.135 2.385,0.302 0.156,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


b.
C346794C01
2.865,2.896 2.719,2.896 2.719,2.896 2.719,2.646 false 1.802,2.927 2.115,3.083 0.313,0.156 10 false *a 2.885,2.823 3.198,2.979 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.38 N*m (136 kgf*cm, 10 ft.*lbf)




Hide 44571A 5.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C346792C01
1.427,1.167 1.656,1.167 1.656,1.167 1.656,0.938 true 1.99,0.76 2.094,0.573 2.094,0.573 2.302,0.573 true 1.823,0.896 1.823,1.281 1.823,1.281 2.01,1.281 true 1,0.792 1.677,0.792 true 1.25,1.094 1.427,1.25 0.177,0.156 10 true *1 2.323,0.5 2.5,0.656 0.177,0.156 10 true *a 0.823,0.719 1.01,0.875 0.188,0.156 10 true *b 2.031,1.198 2.198,1.354 0.167,0.156 10 true *c
*1 Brake Actuator Hose Clamp
*a Protector
*b Identification Mark
*c Contacts


Install the No. 1 brake actuator hose to the brake actuator hose clamp.

NOTICE:
·

Make sure to install the No. 1 brake actuator hose so that the protector on the brake booster pump assembly side contacts the brake actuator hose clamp.

·

Make sure to install the No. 1 brake actuator hose so that its identification mark can be seen.




b.
C346790C01
1.229,2.792 1.417,2.792 1.417,2.792 1.583,2.51 true 1.052,2.708 1.219,2.906 0.167,0.198 10 true *a 1.667,0.354 2.125,0.552 0.458,0.198 10 false 90° 1.677,1.083 2.135,1.281 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 1 brake actuator hose to the No. 1 brake actuator tube to install it, and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 1 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 82111 6.CONNECT ENGINE ROOM MAIN WIRE

a.
C346786C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.




b.
C346788C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.




c.

Engage the clamp to install the engine room main wire.


Hide 88710E 7.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.
C346783

Insert the air conditioner tube and accessory assembly to the air conditioning unit assembly.


e.

Engage the 2 clamps to install the air conditioner tube and accessory assembly.


Hide 88707 8.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Insert the suction pipe sub-assembly to the air conditioning unit assembly.


e.
C346781

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


g.

Engage the 2 clamps to install the suction pipe sub-assembly.


Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 44551C 10.BLEED NO. 1 BRAKE ACTUATOR TUBE

Hide 11.FILL RESERVOIR WITH BRAKE FLUID

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 13.BLEED BRAKE SYSTEM

Hide 14.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 55701J 17.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55736D 18.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 19.INSTALL WATER GUARD PLATE LH

Hide 55737B 20.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 21.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY