Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for LHD)
RM3210E _54 Brake _047517 BRAKE SYSTEM (OTHER) _0243390 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  INSTALLATION  


PROCEDURE

Hide 44785D 1.INSTALL BRAKE MASTER CYLINDER GASKET

a.

Install a new brake master cylinder gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C346777C02
0.26,4.063 0.26,3.781 false 0.615,3.583 0.615,3.229 0.615,3.229 0.417,3.229 false 2.51,4.292 2.51,4.01 false 1.375,2.99 1.375,2.635 1.375,2.635 1.177,2.635 false 1.99,3.344 1.99,2.75 1.99,2.75 1.792,2.75 false 2.385,3.417 2.385,2.823 2.385,2.823 2.625,2.823 false 1.021,2.563 1.333,2.719 0.313,0.156 10 false *a 2.656,2.75 2.969,2.906 0.313,0.156 10 false *b 0.208,4.073 0.521,4.229 0.313,0.156 10 false *c 0.26,3.146 0.573,3.302 0.313,0.156 10 false *d 2.458,4.302 2.771,4.458 0.313,0.156 10 false *e 1.656,2.677 1.969,2.833 0.313,0.156 10 false *f 0.781,1.698 0.927,1.885 0.146,0.188 10 true 1 2.531,0.521 2.677,0.708 0.146,0.188 10 true 2 0.802,0.521 0.948,0.708 0.146,0.188 10 true 3 2.51,1.656 2.656,1.844 0.146,0.188 10 true 4
*a Skid Control ECU
*b No. 1 Reservoir Hose
*c Brake Master Cylinder Push Rod Clevis
*d Boot
*e Master Cylinder Reservoir Assembly
*f Brake Actuator Bracket


Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Tighten the nuts in the order shown in the illustration.

·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




Hide 47264A 3.INSTALL PUSH ROD PIN

Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Hide 5.CONNECT BRAKE LINE

a.

Engage the clamp to install the 3 brake lines.

NOTICE:
·

Do not damage the clamp.

·

Do not kink or damage the brake lines.




b.
C346775C01
2.927,2.885 2.719,2.885 2.719,2.885 2.719,2.635 false 1.781,2.938 2.094,3.094 0.313,0.156 10 false *a 2.958,2.813 3.271,2.969 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 3 brake lines to the brake booster with master cylinder assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.38 N*m (136 kgf*cm, 10 ft.*lbf)




Hide 44572C 6.CONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C346772C01
2.021,2.917 2.021,2.563 true 1.958,2.927 2.135,3.104 0.177,0.177 10 true *a 1.688,0.354 2.146,0.552 0.458,0.198 10 false 90° 1.708,1.135 2.167,1.333 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 2 brake actuator hose to the brake booster with master cylinder assembly, and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 2 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 82111 7.CONNECT ENGINE ROOM MAIN WIRE

a.

Connect the connector to the brake booster with master cylinder assembly.


b.
C346770C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster with master cylinder assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




c.

Engage the clamp to install the engine room main wire.


Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 44551C 10.BLEED NO. 1 BRAKE ACTUATOR TUBE

NOTICE:

Make sure to bleed the air from the No. 1 brake actuator tube. If the air remains in the No. 1 brake actuator tube, the air will enter the brake booster pump assembly and may damage the brake booster pump assembly.


a.

Remove the brake master cylinder reservoir filler cap assembly.


b.

Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3

SAE J1704 or FMVSS No. 116 DOT4



c.
C346762

Remove the nut to separate the No. 1 brake actuator tube.

HINT:

If the No. 1 brake actuator tube has already been separated, it is not necessary to perform this step.



d.
C346763N01
1.875,0.344 2.385,0.344 true 1.771,1.26 2.281,1.26 true 1.552,0.271 1.865,0.448 0.313,0.177 10 true SST 2.313,1.198 2.667,1.375 0.354,0.177 10 true SST

Set SST to the brake master cylinder reservoir assembly.

SST
09992-00242  09992-00350  


e.

Using SST, increase and then maintain the pressure in the brake master cylinder reservoir assembly for 60 seconds.(*1)

Standard Pressure:

50 to 80 kPa (0.6 to 0.8 kgf/cm2, 7.3 to 11.6 psi)



f.

Release the pressure in the brake master cylinder reservoir assembly and wait for 30 seconds.(*2)


g.

Repeat steps *1 to *2, 3 times.


h.

Remove SST.


i.
C346764C01
0,0 0,0 false
V113147

Pull up


Pull up the No. 1 brake actuator tube as shown in the illustration as high as possible for 10 seconds without damaging the bracket of the No. 1 brake actuator tube.(*3)

NOTICE:

Do not damage the hoses.


HINT:

Elevating the No. 2 brake actuator hose causes any air in the horizontal portion of the hose to flow to the brake master cylinder reservoir assembly side.



j.

Repeat step *3, 5 times.


k.
C346765C01
0,0 0,0 false
V113147

Pull up


Elevate the No. 1 brake actuator tube for 10 seconds by lifting the No. 1 brake actuator tube as shown in the illustration.(*4)

NOTICE:

Do not damage the hoses.


HINT:

Elevating the No. 1 brake actuator tube causes any air in the horizontal portion of the tube to flow to the brake master cylinder reservoir assembly side.



l.
C346766C01
0,0 0,0 false
V113147

Press down


Lower the No. 1 brake actuator tube for 10 seconds as shown in the illustration.(*5)

NOTICE:

Do not damage the hoses.


HINT:

Lowering the No. 1 brake actuator tube causes any air in the No. 1 brake actuator tube to flow to the brake master cylinder reservoir assembly side.



m.

Repeat steps *4 to *5, 5 times.


n.

Install the No. 1 brake actuator tube with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 11.CONNECT BRAKE BOOSTER PUMP CONNECTOR

HINT:

Perform this operation only when the accumulator pressure zero down could not be performed using the GTS.


a.
C346786C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




Hide 12.FILL RESERVOIR WITH BRAKE FLUID

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 14.BLEED BRAKE SYSTEM

Hide 15.INSPECT AND ADJUST BRAKE PEDAL

Hide 16. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

Hide 55606 17.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62112 18.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914 19.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 55701J 20.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55736D 21.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 22.INSTALL WATER GUARD PLATE LH

Hide 55737B 23.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 24.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY