Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244738 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: for LH Side

Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Rear height control sensor sub-assembly LH*1

·

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)


Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 57628C 2.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

Hide 58390 3.REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

Hide 89408C 4.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 48540 5.SEPARATE REAR SHOCK ABSORBER ASSEMBLY

a.
C345076

Remove the 2 bolts and separate the rear shock absorber assembly from the vehicle.


Hide 48540 6.LOOSEN REAR SHOCK ABSORBER ASSEMBLY

a.
C345070C01
0.865,0.5 1.063,0.5 1.063,0.5 1.323,0.813 true 0.635,0.417 0.854,0.615 0.219,0.198 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



Hide 48840A 7.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48790 8.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY

a.
C345074

Remove the bolt and nut, and separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48540 9.REMOVE REAR SHOCK ABSORBER ASSEMBLY

a.
C347353C01
0.833,0.563 1.052,0.563 1.052,0.563 1.323,0.823 true 0.615,0.5 0.833,0.688 0.219,0.188 10 true *1
*1 Rear Axle Carrier Pin


Remove the nut and rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



Hide 48554A 10.REMOVE REAR SHOCK ABSORBER CAP

a.
C345075C01
1.708,0.823 1.708,0.344 1.708,0.344 1.469,0.344 false 1.302,0.271 1.615,0.427 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear shock absorber cap from the rear shock absorber assembly.


Hide 48760B 11.REMOVE REAR SUSPENSION SUPPORT ASSEMBLY

a.
C347354C01
2.417,1.135 2.542,0.594 2.542,0.594 2.76,0.594 false 2.802,0.521 3.26,0.719 0.458,0.198 10 false SST 1.76,2.854 2.073,3.01 0.313,0.156 10 false *a 3.021,2.219 3.333,2.375 0.313,0.156 10 false *b
*a Turn
*b Hold


Secure the rear shock absorber assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and remove the rear support to rear shock absorber nut.

SST
09729-97202  


c.

Remove the rear suspension support assembly from the rear shock absorber assembly.