Home › Suspension › REAR SUSPENSION › REAR LOWER ARM
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244741 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48720A 1.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.

Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly and rear suspension member sub-assembly with the 2 bolts and 2 nuts.

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Insert the bolt with the threaded end facing the rear of the vehicle.




Hide 48740F 2.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and nut.

NOTICE:
·

Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle.

·

When tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.




Hide 48258C 3.INSTALL REAR LOWER COIL SPRING INSULATOR

Hide 48231B 4.INSTALL REAR COIL SPRING

Hide 48840A 6.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 48720A 7.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

a.
C350135

Install the rear No. 1 suspension arm assembly with the 2 bolts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48740F 8.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.
C350136

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 89408C 9.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 57628C 10.INSTALL REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

Hide 58390 11.INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY (for RH Side)

Hide 12.INSTALL REAR WHEEL

Hide 48740F 13.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Lower the vehicle to the ground.


b.

Bounce the vehicle up and down at the corners to stabilize the rear suspension.


c.
C348389C03
2.125,0.823 2.354,0.823 true 2.125,1.208 2.125,0.771 2.125,0.771 2.344,0.771 true 1.156,1.646 1.156,1.344 1.156,1.344 0.927,1.344 true 0.917,1.406 1.146,1.406 true 2.052,1.229 2.281,1.417 0.229,0.188 10 true *a 1.063,1.656 1.292,1.844 0.229,0.188 10 true *a
*a Matchmark


Align the matchmarks on the No. 2 camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.


d.

Fully tighten the nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:
·

Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

·

Make sure that the vehicle is unloaded when fully tightening the nut.




Hide 14.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 15.PERFORM INITIALIZATION

Intelligent clearance sonar system
Simple intelligent parking assist system
(Click here)
Parking assist monitor system (Click here)
Automatic headlight beam level control system (Click here)