Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2016.08
RM3210E _56 Audio / Visual / Telematics _047510 AUDIO / VIDEO _0243397 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

w/o Manual (SOS) Switch
·

The radio and display receiver assembly and telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio and display receiver assembly sends power to the telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2, and the telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 sends microphone signals to the radio and display receiver assembly.


w/ Manual (SOS) Switch
·

The radio and display receiver assembly and telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the telematics transceiver sends power to the telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2, and the telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 sends microphone signals to the radio and display receiver assembly via the telematics transceiver.


*1: w/o Sliding Roof

*2: w/ Sliding Roof


WIRING DIAGRAM

E334513E04
0.875,0.646 1.49,0.844 0.615,0.198 10 false SNS2 0.833,1.063 1.448,1.26 0.615,0.198 10 false MACC 0.844,1.479 1.458,1.677 0.615,0.198 10 false MCO+ 0.865,1.906 1.479,2.104 0.615,0.198 10 false MCO- 1.333,0.542 1.667,0.729 0.333,0.188 10 false 14*2 1.406,0.385 1.74,0.573 0.333,0.188 10 false 3*1 1.333,0.958 1.667,1.146 0.333,0.188 10 false 17*2 1.406,0.802 1.74,0.99 0.333,0.188 10 false 1*1 1.333,1.385 1.667,1.573 0.333,0.188 10 false 16*2 1.406,1.229 1.74,1.417 0.333,0.188 10 false 2*1 1.333,1.813 1.667,2 0.333,0.188 10 false 15*2 1.406,1.656 1.74,1.844 0.333,0.188 10 false 4*1 0.073,2.302 0.458,2.5 0.385,0.198 10 false O2*1 0.083,2.469 2.302,2.698 2.219,0.229 10 false Telephone Microphone Assembly*1 0.073,2.927 0.458,3.125 0.385,0.198 10 false O4*2 0.073,3.083 2.031,3.458 1.958,0.375 10 false Map Light Assembly (Telephone Microphone Assembly)*2 2.052,2.167 2.708,2.385 0.656,0.219 10 false (Shielded) 3.24,0.958 3.458,1.156 0.219,0.198 10 false 33 3.24,1.375 3.458,1.573 0.219,0.198 10 false 34 3.24,1.792 3.458,1.99 0.219,0.198 10 false 35 3.24,2.219 3.458,2.417 0.219,0.198 10 false 32 3.49,1.073 3.938,1.271 0.448,0.198 10 false MCVD 3.49,1.49 3.885,1.688 0.396,0.198 10 false MCI+ 3.49,1.906 4.104,2.104 0.615,0.198 10 false MCI- 3.49,2.333 4.104,2.531 0.615,0.198 10 false SGND 3.958,1.198 4.406,1.396 0.448,0.198 10 false MCO+ 3.958,1.625 4.406,1.823 0.448,0.198 10 false MCO- 4.438,1.094 4.656,1.292 0.219,0.198 10 false 18 4.438,1.521 4.656,1.719 0.219,0.198 10 false 19 4.802,1.885 5.458,2.104 0.656,0.219 10 false (Shielded) 3.042,2.688 3.427,2.885 0.385,0.198 10 false F36 3.042,2.854 4.927,3.083 1.885,0.229 10 false Telematics Transceiver 5.927,0.656 6.542,0.854 0.615,0.198 10 false SNS2 5.938,1.208 6.385,1.406 0.448,0.198 10 false MIN+ 5.938,1.625 6.385,1.823 0.448,0.198 10 false MIN- 5.938,2.042 6.552,2.24 0.615,0.198 10 false SGND 5.76,0.542 5.979,0.74 0.219,0.198 10 false 6 5.76,1.094 5.979,1.292 0.219,0.198 10 false 5 5.688,1.521 5.906,1.719 0.219,0.198 10 false 19 5.688,1.938 5.906,2.135 0.219,0.198 10 false 18 5.75,2.438 6.135,2.635 0.385,0.198 10 false F31 5.75,2.604 7.021,3.021 1.271,0.417 10 false Radio and Display Receiver Assembly 2.25,3.885 3.615,4.125 1.365,0.24 10 false *1: w/o Sliding Roof 2.25,4.281 3.615,4.521 1.365,0.24 10 false *2: w/ Sliding Roof

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
OK A
NG
(w/o Manual (SOS) Switch and w/o Sliding Roof)
B
NG
(w/o Manual (SOS) Switch and w/ Sliding Roof)
C
NG
(w/ Manual (SOS) Switch and w/o Sliding Roof)
D
NG
(w/ Manual (SOS) Switch and w/ Sliding Roof)
E



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

C

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

D

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

E

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the O2 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-6 (SNS2) - O2-3 (SNS2) Always Below 1 Ω
F31-4 (MACC) - O2-1 (MACC) Always Below 1 Ω
F31-5 (MIN+) - O2-2 (MCO+) Always Below 1 Ω
F31-19 (MIN-) - O2-4 (MCO-) Always Below 1 Ω
F31-6 (SNS2) or O2-3 (SNS2) - Body ground Always 10 kΩ or higher
F31-4 (MACC) or O2-1 (MACC) - Body ground Always 10 kΩ or higher
F31-5 (MIN+) or O2-2 (MCO+) - Body ground Always 10 kΩ or higher
F31-19 (MIN-) or O2-4 (MCO-) - Body ground Always 10 kΩ or higher
F31-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F31 radio and display receiver assembly connector.


b.

Reconnect the O2 telephone microphone assembly connector.


c.
E289390C27
1.49,0.521 1.865,0.76 0.375,0.24 2.188,2 2.469,2.677 false 2.052,2 1.323,2.677 false 2.448,0.969 2.198,1.729 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.552,0.552 1.865,0.75 0.313,0.198 10 false F31 2.333,2.688 2.844,2.948 0.51,0.26 10 false SGND 2.292,0.792 2.802,1.052 0.51,0.26 10 false MACC 1.146,2.677 1.656,2.938 0.51,0.26 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F31-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-18 (SGND) - Body ground Always Below 1 Ω
F31-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.
E221776C04
1.375,1.583 1.625,1.229 false 2,1.583 1.792,1.24 false 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 1.219,1.625 1.625,1.823 0.406,0.198 10 false MCO- 1.854,1.635 2.26,1.833 0.406,0.198 10 false SNS2
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY

5.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Reconnect the F31 radio and display receiver assembly connector.


b.

Reconnect the O2 telephone microphone assembly connector.


c.

Turn the power switch on (ACC).


d.
E279075C05
1.302,1 1.719,1.25 0.417,0.25 1.625,2.021 2.083,1.333 false 1.625,2.396 2,2.75 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.406,1.031 1.719,1.229 0.313,0.198 10 false O2 2.063,1.146 2.563,1.344 0.5,0.198 10 false MCO+ 2.031,2.76 2.531,2.958 0.5,0.198 10 false MCO-
*a Component with harness connected
(Telephone Microphone Assembly)


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the O2 telephone microphone assembly connector.


e.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the telephone microphone assembly is output. A
A waveform synchronized with the voice input to the telephone microphone assembly is not output. B




A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

REPLACE TELEPHONE MICROPHONE ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the O4 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-6 (SNS2) - O4-14 (SNS2) Always Below 1 Ω
F31-4 (MACC) - O4-17 (MACC) Always Below 1 Ω
F31-5 (MIN+) - O4-16 (MCO+) Always Below 1 Ω
F31-19 (MIN-) - O4-15 (MCO-) Always Below 1 Ω
F31-6 (SNS2) - Body ground Always 10 kΩ or higher
F31-4 (MACC) - Body ground Always 10 kΩ or higher
F31-5 (MIN+) - Body ground Always 10 kΩ or higher
F31-19 (MIN-) - Body ground Always 10 kΩ or higher
F31-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F31 radio and display receiver assembly connector.


b.

Reconnect the O4 map light assembly (telephone microphone assembly) connector.


c.
E289390C27
1.49,0.521 1.865,0.76 0.375,0.24 2.188,2 2.469,2.677 false 2.052,2 1.323,2.677 false 2.448,0.969 2.198,1.729 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.552,0.552 1.865,0.75 0.313,0.198 10 false F31 2.333,2.688 2.844,2.948 0.51,0.26 10 false SGND 2.292,0.792 2.802,1.052 0.51,0.26 10 false MACC 1.146,2.677 1.656,2.938 0.51,0.26 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F31-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-18 (SGND) - Body ground Always Below 1 Ω
F31-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E187117C66
1.885,1.385 2.344,1.792 2.344,1.792 2.552,1.792 false 1.771,1.385 1.531,1.792 1.531,1.792 1.281,1.792 false 0.865,1.698 1.281,1.906 0.417,0.208 10 false MCO- 2.594,1.688 3.01,1.885 0.417,0.198 10 false SNS2 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 15 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
9.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F31 radio and display receiver assembly connector.


b.

Reconnect the O4 map light assembly (telephone microphone assembly) connector.


c.

Turn the power switch on (ACC).


d.
E187122C69
1.49,0.542 1.906,0.792 0.417,0.25 1.656,2.24 1.083,2.958 false 2.49,2.958 1.802,2.229 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 0.833,2.99 1.313,3.188 0.479,0.198 10 false MCO+ 2.385,2.979 2.99,3.156 0.604,0.177 10 false MCO- 1.604,0.583 1.938,0.75 0.333,0.167 10 false O4
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 16 (MCO+) and 15 (MCO-) of the O4 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

10.REPLACE TELEPHONE MICROPHONE ASSEMBLY
10.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur (returns to normal). A
Malfunction recurs. B




A

END

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the O2 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-6 (SNS2) - O2-3 (SNS2) Always Below 1 Ω
F31-6 (SNS2) or O2-3 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F36 telematics transceiver connector.


b.

Disconnect the O2 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F36-33 (MCVD) - O2-1 (MACC) Always Below 1 Ω
F36-34 (MCI+) - O2-2 (MCO+) Always Below 1 Ω
F36-35 (MCI-) - O2-4 (MCO-) Always Below 1 Ω
F36-33 (MCVD) or O2-1 (MACC) - Body ground Always 10 kΩ or higher
F36-34 (MCI+) or O2-2 (MCO+) - Body ground Always 10 kΩ or higher
F36-35 (MCI-) or O2-4 (MCO-) - Body ground Always 10 kΩ or higher
F36-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the O4 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-6 (SNS2) - O4-14 (SNS2) Always Below 1 Ω
F31-6 (SNS2) or O4-14 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F36 telematics transceiver connector.


b.

Disconnect the O4 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F36-33 (MCVD) - O4-17 (MACC) Always Below 1 Ω
F36-34 (MCI+) - O4-16 (MCO+) Always Below 1 Ω
F36-35 (MCI-) - O4-15 (MCO-) Always Below 1 Ω
F36-33 (MCVD) or O4-17 (MACC) - Body ground Always 10 kΩ or higher
F36-34 (MCI+) or O4-16 (MCO+) - Body ground Always 10 kΩ or higher
F36-35 (MCI-) or O4-15 (MCO-) - Body ground Always 10 kΩ or higher
F36-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F31 radio and display receiver assembly connector.


b.

Disconnect the F36 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-5 (MIN+) - F36-18 (MCO+) Always Below 1 Ω
F31-19 (MIN-) - F36-19 (MCO-) Always Below 1 Ω
F31-5 (MIN+) or F36-18 (MCO+) - Body ground Always 10 kΩ or higher
F31-19 (MIN-) or F36-19 (MCO-) - Body ground Always 10 kΩ or higher
F31-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the F36 telematics transceiver connector.


b.
E289390C38
1.521,0.698 1.896,0.938 0.375,0.24 2.552,2.531 2.198,1.958 false 2.063,2.771 2.063,1.969 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.573,0.729 1.885,0.927 0.313,0.198 10 false F31 2.542,2.552 3.063,2.76 0.521,0.208 10 false SGND 2.01,2.802 2.531,3.01 0.521,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-18 (SGND) - Body ground Always Below 1 Ω
F31-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.INSPECT TELEMATICS TRANSCEIVER

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

17.INSPECT TELEMATICS TRANSCEIVER
a.

Reconnect the F36 telematics transceiver connector.


b.
E259127C32
1.479,0.708 1.917,0.979 0.438,0.271 0.573,2.719 1.177,2.094 false 1.188,2.729 1.385,2.094 false 1.99,2.74 1.49,2.094 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.583,0.76 1.917,0.958 0.333,0.198 10 false F36 0.302,2.74 0.719,2.906 0.417,0.167 10 false MCI- 0.833,2.781 1.333,2.948 0.5,0.167 10 false MCVD 1.99,2.771 2.49,2.938 0.5,0.167 10 false SGND
*a Component with harness connected
(Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Tester Connection Condition Specified Condition
F36-33 (MCVD) - Body ground Power switch on (ACC) 4 to 6 V
F36-32 (SGND) - Body ground Always Below 1 Ω
F36-35 (MCI-) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (w/o Sliding Roof) A
OK (w/ Sliding Roof) B
NG C



A

18.INSPECT TELEPHONE MICROPHONE ASSEMBLY

B

20.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

C

18.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.
E221776C03
1.375,1.583 1.625,1.229 false 2,1.583 1.792,1.24 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.073,1.604 1.479,1.802 0.406,0.198 10 false MCO- 1.979,1.615 2.385,1.813 0.406,0.198 10 false SNS2
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY

19.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Turn the power switch on (ACC).


b.
E279075C04
0.542,2.125 0.958,2.375 0.417,0.25 1.594,2.073 1.99,1.375 false 1.594,2.323 1.958,2.719 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.667,2.177 0.979,2.375 0.313,0.198 10 false O2 1.979,1.188 2.479,1.385 0.5,0.198 10 false MCO+ 1.927,2.74 2.427,2.938 0.5,0.198 10 false MCO-
*a Component with harness connected
(Telephone Microphone Assembly)


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the O2 telephone microphone assembly connector.


c.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the telephone microphone assembly is output. A
A waveform synchronized with the voice input to the telephone microphone assembly is not output. B




A

B

REPLACE TELEPHONE MICROPHONE ASSEMBLY

20.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E187117C67
2.031,1.698 1.885,1.375 false 1.604,1.688 1.771,1.375 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.021,1.719 2.635,1.917 0.615,0.198 10 false SNS2 1.281,1.708 1.896,1.906 0.615,0.198 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 15 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
21.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Turn the power switch on (ACC).


b.
E187122C70
1.49,0.542 1.906,0.792 0.417,0.25 1.24,2.865 1.656,2.219 false 1.781,2.208 2.115,2.833 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 0.854,2.865 1.333,3.063 0.479,0.198 10 false MCO+ 2.125,2.854 2.729,3.031 0.604,0.177 10 false MCO- 1.615,0.594 1.948,0.76 0.333,0.167 10 false O4
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 16 (MCO+) and 15 (MCO-) of the O4 map light assembly (telephone microphone assembly) connector.


c.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

22.REPLACE TELEPHONE MICROPHONE ASSEMBLY
22.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur (returns to normal). A
Malfunction recurs. B




A

END

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)