2005-2008 RAV4 · Service Manual BRAKE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008


DIAGNOSIS
The table below indicates which lights come on when there are malfunctions in particular functions.
  1. w/o Multi-information display:
    If the skid control ECU detects a malfunction, the ABS, VSC and Brake warning lights and the Slip and downhill assist control indicator lights come on in accordance with the trouble area to warn the driver.
  2. w/ Multi-information display:
    If the skid control ECU detects a malfunction, the ABS and BRAKE warning lights and the master caution, SLIP and Downhill assist control indicator lights come on and the multi-information display warning messages in accordance with the trouble area to warn the driver.
C131009E01
Item / Trouble Area
ABS
EBD
BA (Brake Assist)
TRC
VSC
Downhill Assist Control*3
Hill-start Assist Control*4
ABS warning light*1
ABS warning light and warning message*2
○
○
○
-
-
-
-
Brake warning light*1
Brake warning light and warning message*2
-
○
○*5
-
-
-
-
VSC warning light*1
Master caution indicator light and warning message*2
○
○
○
○
○
○
○
Slip indicator light
○
○
○
○
○
○
○
Downhill assist control indicator light*3
●
(Downhill assist control switch ON)
●
(Downhill assist control switch ON)
●
(Downhill assist control switch ON)
●
(Downhill assist control switch ON)
●
(Downhill assist control switch ON)
●
(Downhill assist control switch ON)
●
(Downhill assist control switch ON)
  1. ○: Light ON
  2. ●: Light ON (Blinking)
  3. -: Light OFF

HINT:
  1. *1: w/o Multi-information display
  2. *2: w/ Multi-information display
  3. *3: w/ Downhill assist control
  4. *4: w/ Hill-start assist control
  5. *5: w/ 16-inch disc
  6. The DTCs can be read by connecting SST (09843-18040) between the TC and CG terminals of the DLC3 and observing the blinking pattern of the ABS warning light and VSC warning light*1 or the multi-information display*2, or by using the intelligent tester (Click here).
  7. This system has a sensor signal check function (Click here).


CHECK WARNING LIGHT AND INDICATOR LIGHT
  1. Release the parking brake lever.

    NOTICE:
    Before releasing the parking brake lever, set chocks to hold the vehicle for safety.

    HINT:
    When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.

  2. When the ignition switch is turned on (IG), check that the ABS, VSC (w/o Multi-information display) and Brake warning lights and the master caution (w/ Multi-information display), Slip and downhill assist control indicator lights come on and go off in about 3 seconds.
    C131033E01

    HINT:
    If the warning lights do not illuminate, confirm whether the bulbs have burned out, and also check for CAN communication system DTCs, since the skid control ECU and combination meter are connected by the CAN communication line.
    If the warning light remains on, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.
    Section Title
    See procedure
    ABS Warning Light Remains ON
    Click here
    VSC Warning Light Remains ON
    Click here
    Brake Warning Light Remains ON
    Click here
    Slip Indicator Light Remains ON
    Click here
    Downhill Assist Control Indicator Light Remains ON
    Click here

← DIAGNOSIS SYSTEM (Nov 2005 – Dec 2006)DIAGNOSIS SYSTEM (Aug 2007 – Jul 2008) →