C1405 Open or Short in Front Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built from Aug 2008
Also covers:
- C1406 Open or Short in Front Speed Sensor LH Circuit
DESCRIPTION
The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS/VSC/TRC control.Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1405 C1406 |
Either of the following is detected:
|
|
- HINT:
- DTC C1405 is for the front speed sensor RH.
- DTC C1406 is for the front speed sensor LH.
- DTC C1405 is for the front speed sensor RH.
WIRING DIAGRAM
Refer to DTCs C1401 and C1402 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
FR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
FL Speed Open
FL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
- OK:
- There are no momentary interruptions.
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
ABS/VSC/TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer.
FL Wheel Speed
FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer.
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
- Result:
Result
Proceed to
DTCs (C1405 and C1406) are not output.
A
DTCs (C1405 and/or C1406) are output.
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Turn the ignition switch off.

Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the skid control ECU connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for RH:
Tester Connection
Condition
Specified Condition
A67-7 (FR+) - A62-1
Always
Below 1 Ω
A67-7 (FR+) - Body ground
Always
10 kΩ or higher
A67-6 (FR-) - A62-2
Always
Below 1 Ω
A67-6 (FR-) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
A67-19 (FL+) - A61-1
Always
Below 1 Ω
A67-19 (FL+) - Body ground
Always
10 kΩ or higher
A67-18 (FL-) - A61-2
Always
Below 1 Ω
A67-18 (FL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT SKID CONTROL ECU (SENSOR INPUT) |
Reconnect the skid control ECU connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for RH:
Tester Connection
Switch Condition
Specified Condition
A62-1 - Body ground
Ignition switch ON
8 to 14 V
- for LH:
Tester Connection
Switch Condition
Specified Condition
A61-1 - Body ground
Ignition switch ON
8 to 14 V
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
