C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2008
Also covers:
- C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction
DESCRIPTION
The brake pedal load sensing switch operates when the brake pedal is depressed with force exceeding a predetermined level.The skid control ECU detects if the brake pedal is depressed or not via this circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1430 |
Either of the following is detected:
|
|
| C1431 |
Either of the following is detected:
|
|
WIRING DIAGRAM
Refer to DTC C1429 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
- HINT:
- When C1425 is output together with C1430 and/or C1431, inspect and repair the trouble areas indicated by C1425 first (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH/BRAKE PEDAL LOAD SENSING SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List mode on the intelligent tester (Click here).
ABS/VSC/TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.
- OK:
- First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.
- Result:
Result
Proceed to
OK
A
NG
Turning on of the brake pedal load sensing switch is not confirmed.
B
The brake pedal load sensing switch turns on first.
C
|
|
||||
|
|
||||
| A | |
| 2. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Perform the road and braking test.
Check if the same DTC is output (Click here).
- Result:
Result
Proceed to
DTCs (C1430 and C1431) are not output.
A
DTCs (C1430 and/or C1431) are output.
B
|
|
||||
| A | ||
| ||
| 3. INSPECT BRAKE PEDAL LOAD SENSING SWITCH |


- NOTICE:
- Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
- When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.
- Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the brake pedal load sensing switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Brake pedal load sensing switch off
(Brake pedal depressed)
0.9 to 1.1 kΩ
Brake pedal load sensing switch on
(Brake pedal released)
192 to 234 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH) |
Make sure that there is no looseness in the locking part and connecting part of the connector.

Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A67-27 (FSW+) - A3-2
Always
Below 1 Ω
A67-27 (FSW+) - Body ground
Always
10 kΩ or higher
A3-1 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
- OK:
- The brake pedal height and stop light switch installation are normal.
|
|
||||
| OK | ||
| ||
