PROBLEM SYMPTOMS TABLE
Troubleshooting · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
- HINT:
- Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
- Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
| Symptom |
Suspected area |
See page |
| No functions of A/C system operate |
1. ECU-IG2 fuse |
- |
| 2. Wire harness or connector |
- |
|
| 3. Air conditioning amplifier |
Click here
|
|
| Airflow Control: Blower motor does not operate |
1. HTR, ECU-IG1 fuse |
- |
| 2. Blower motor circuit |
Click here
|
|
| 3. Blower motor |
Click here
|
|
| 4. Wire harness or connector |
- |
|
| Airflow Control: Blower motor does not change speed |
1. Blower resistor |
Click here
|
| 2. Blower motor |
Click here
|
|
| 3. Heater control (blower switch) |
- |
|
| Temperature Control: No cool air comes out |
1. Refrigerant volume |
Click here
|
| 2. Refrigerant pressure |
Click here
|
|
| 3. Air conditioning pressure sensor circuit |
Click here
|
|
| 4. Heater control base (w/ A/C switch) |
- |
|
| 5. Air mix control knob (w/o Heater) |
- |
|
| 6. Compressor and pulley (for 2AD-FHV) |
Click here
|
|
| 7. Compressor and pulley (for 2AD-FTV) |
Click here
|
|
| 8. Compressor and pulley (for 1AZ-FE) |
Click here
|
|
| 9. Compressor and pulley (for 2AZ-FE) |
Click here
|
|
| 10. Expansion valve |
- |
|
| 11. Air conditioning amplifier |
Click here
|
|
| 12. ECM (for 2AD-FHV) |
Click here
|
|
| 13. ECM (for 2AD-FTV) |
Click here
|
|
| 14. ECM (for 1AZ-FE) |
Click here
|
|
| 15. ECM (for 2AZ-FE) |
Click here
|
|
| 16. CAN communication |
Click here
|
|
| Compressor and pulley do not operate |
1. ECU-IG2 fuse |
- |
| 2. Refrigerant pressure |
Click here
|
|
| 3. Compressor and pulley (for 2AD-FHV) |
Click here
|
|
| 4. Compressor and pulley (for 2AD-FTV) |
Click here
|
|
| 5. Compressor and pulley (for 1AZ-FE) |
Click here
|
|
| 6. Compressor and pulley (for 2AZ-FE) |
Click here
|
|
| 7. Air conditioning pressure sensor circuit |
Click here
|
|
| 8. Evaporator temperature sensor circuit |
Click here
|
|
| 9. Heater control base (w/ A/C switch) |
- |
|
| 10. Air mix control knob (w/o Heater) |
- |
|
| 11. Air conditioning amplifier |
- |
|
| 12. ECM (for 2AD-FHV) |
Click here
|
|
| 13. ECM (for 2AD-FTV) |
Click here
|
|
| 14. ECM (for 1AZ-FE) |
Click here
|
|
| 15. ECM (for 2AZ-FE) |
Click here
|
|
| 16. CAN communication |
Click here
|