2005-2008 RAV4 · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. INSTALL REAR DRIVE SHAFT ASSEMBLY LH
  1. Align the splines of the rear drive shaft outboard joints and, install the left and right rear drive shafts to the axle hub.


2. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
  1. Apply hypoid gear oil to the splines of the left and right rear drive shaft inboard joints.

  1. C129504
    Align the splines of the rear drive shaft inboard joints and, using a brass bar and hammer, tap in the left and right rear drive shafts.

    NOTICE:
    1. Face the cutout section of the snap ring downward.
    2. Do not damage the oil seal during the insertion.
    3. Do not strike the tip of the outboard joint with the hammer.

    HINT:
    Determine whether or not the rear drive shaft is completely tapped in by checking for changes in sound or the reaction force of the brass bar.

  1. C129479E01
    Slowly raise the transmission jack, fix the nuts in place and install the 3 bolts.

    Torque:
    86 N*m{ 877 kgf*cm , 63 ft.*lbf } for bolt A
    140 N*m{ 1428 kgf*cm , 103 ft.*lbf } for bolt B

    NOTICE:
    Tighten the bolts, not the nuts.


3. INSTALL REAR SPEED SENSOR LH
  1. Install the speed sensor (Click here).


4. INSTALL REAR AXLE SHAFT NUT

C129485
  1. Install a new hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 159 ft.*lbf } for φ 26
    292 N*m{ 2,978 kgf*cm , 215 ft.*lbf } for φ 30

  1. Using a chisel and hammer, stake the hub nut.


5. TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

  1. C127526E01
    Align the matchmarks of the transfer and propeller shaft.

  1. Temporarily install the propeller shaft with center bearing with the 4 nuts and 4 washers.

  1. C127525E01
    Align the matchmarks of the differential carrier and propeller shaft.

  1. Temporarily install the propeller shaft with center bearing with the 4 bolts and 4 washers.

  1. C127524
    Temporarily install the center support bearing and center support bearing washer with the 2 bolts.


6. TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Tighten the 4 nuts of the propeller shaft and transfer to the torque specification.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Tighten the 4 nuts of the propeller shaft and differential carrier to the torque specification.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Check that the center line of the center support bearing housing is perpendicular to the axis of the propeller shaft.

  1. Tighten the 2 bolts of the center support bearing to the torque specification.

    Torque:
    36.8 N*m{ 375 kgf*cm , 27 ft.*lbf }


7. INSPECT JOINT ANGLE

NOTICE:
Perform the measurement with a 4 post lift or pit so that the vehicle is supported by all 4 wheels as if it were on the ground.

  1. Before the angle measurement, stabilize each part by performing procedures like those described below.

    1. Rotate the propeller shaft several times by hand.

    2. Set the jack to the differential, and raise and lower the differential.

  1. Using SST and a straightedge, measure the angle of the transfer flange (angle D) and the angle of the intermediate shaft (angle A).

    SST
    09370-50010  

    NOTICE:
    Make sure the straightedge and SST are at a right angle.


    C190639E01

    1. Subtract the measured angle of the intermediate shaft (angle A) from the measured angle of the transfer flange (angle D) to obtain the No. 1 joint angle.

      No. 1 Joint Angle:
      Measurement Position
      No. 1 Joint Angle
      D - A
      2°27' +/-60'

  1. Using SST, measure the angle of the intermediate shaft (angle A) and the angle of the propeller shaft (angle B).

    SST
    09370-50010  

    C190640E01

    1. Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the intermediate shaft (angle A) to obtain the No. 2 joint angle.

      No. 2 Joint Angle:
      Measurement Position
      Engine
      Transmission
      No. 2 Joint Angle
      A - B
      1AZ-FE
      A/T
      1°29' +/-1°30'
      M/T
      1°28' +/-1°30'
      2AZ-FE
      A/T
      1°35' +/-1°30'
      M/T
      1°34' +/-1°30'
      2GR-FE
      A/T
      1°35' +/-1°30'
      2AD-FTV
      2AD-FHV
      M/T
      1°28' +/-1°30'

  1. Using SST, measure the angle of the propeller shaft (angle B) and the angle of the rear differential (angle C).

    SST
    09370-50010  

    C190641E01

    1. Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the rear differential (angle C) to obtain the No. 3 joint angle.

      No. 3 Joint Angle:
      Measurement Position
      Engine
      Transmission
      No. 3 Joint Angle
      B - C
      1AZ-FE
      A/T
      2°10' +/-60'
      M/T
      2°11' +/-60'
      2AZ-FE
      A/T
      2°04' +/-60'
      M/T
      2GR-FE
      A/T
      2°04' +/-60'
      2AD-FTV
      2AD-FHV
      M/T
      2°10' +/-60'


8. INSTALL NO. 2 EXHAUST PIPE SUB-ASSEMBLY
  1. Install the No. 2 exhaust pipe sub-assembly for 2GR-FE (Click here).


9. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front pipe for 2AD-FTV (Click here for CCo, Click here for DPF).

  1. Install the front pipe for 2AD-FHV (Click here).


10. INSTALL EXHAUST CENTER PIPE ASSEMBLY
  1. Install the center pipe for 1AZ-FE (Click here).

  1. Install the center pipe for 2AZ-FE (Click here).


11. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe for 1AZ-FE (Click here).

  1. Install the tailpipe for 2AD-FTV (Click here for CCo, Click here for DPF).

  1. Install the tailpipe for 2AD-FHV (Click here).

  1. Install the tailpipe for 2AZ-FE (Click here).

  1. Install the tailpipe for 2GR-FE (Click here).


12. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


13. ADD DIFFERENTIAL OIL
  1. Add differential oil (Click here).


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

15. INSPECT FOR DIFFERENTIAL OIL LEAK

16. INSPECT FOR EXHAUST GAS LEAK
  1. If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

17. INSPECT REAR WHEEL ALIGNMENT
  1. Inspect the rear wheel alignment (Click here).

← INSTALLATION (Jan 2007 – Jul 2007)PRECAUTION (from Nov 2005) →