Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > Black Smoke Emitted

for Preparation Click here


DESCRIPTION


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Intake System 
    Component
    Intake system
    Symptom: Main fault
    1. Lack of power (no black smoke): air filter blockage, Air duct is crushed/leaking
    2. Black smoke (no lack of power): Leakage between the turbo and intake manifold
    Data List
    1. MAP (inside intake air pressure)
    2. Target Booster Pressure
      When the accelerator is fully depressed, if the MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

    Turbocharger System 
    Component
    Turbocharger system
    Main fault
    1. Air leak in the turbocharged air passage
    2. Turbo motor driver not operating well
    3. Turbocharger (turbine, bearing)
    Symptoms
    Lack of power (when vehicle starting, when heavy load)
    (Black smoke is not emitted when racing while vehicle stopped)
    Data List
    MAP (inside intake air pressure), Target Booster Pressure
    1. When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
    2. With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
    3. Atmospheric pressure decreases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions.
    VN Turbo Command
    1. 0%: Vanes fully open (drive rod contracts)
    2. Over 90%: Vanes fully closed (drive rod expands and turbo operates effectively)

    Glow System 
    Component
    Glow system
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Try to measure the resistance of the glow plug

    Engine 
    Component
    Engine
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.

  2. Diesel Injection

    Fuel Supply Pump 
    Component
    Fuel supply pump
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    1. The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
    2. When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Injector 
    Component
    Fuel injector
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

    HINT:
    1. When the sliding resistance of the internal parts of the injectors (i.e. armature shaft, command piston and plunger) has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector closing.
    2. When black smoke occurs due to contamination of the injectors, there are usually other symptoms, such as engine knocking noise at cold idling, rough idling, difficult to start, etc. which are also present at low common rail pressure.


    Injector Driver (EDU) 
    Component
    Injector Driver (EDU)
    Main fault
    Circuit fault: The fuel injector does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as fuel injector
    Diagnostic Trouble Code
    When the EDU has a fault, some DTCs may be stored.

    Fuel Pressure Sensor 
    Component
    Fuel pressure sensor
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (however, the value may not deviate even when a malfunction is present).
    Diagnostic Trouble Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.

    Irregular Fuel 
    Component
    Irregular fuel
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel EGR

    EGR System 
    Component
    EGR system
    Main fault
    1. Does not move smoothly
    2. Does not close completely
    Symptoms
    1. Rough idle
    2. EGR valve stuck closed: A loud turbocharger sound.
    3. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
    Data List
    Actual EGR Valve Pos., Target EGR Pos.
    1. Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
    2. Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
    3. EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).
    4. EGR valve opens to the halfway point at idling after the engine is warmed up.
    EGR Close Lrn. Val., EGR Close Lrn. Status
    1. When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0.34 to 0.70 V.
    2. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0.34 to 0.70 V), it is possible that the EGR valve cannot completely close.

  4. Diesel Throttle

    Diesel Throttle System 
    Component
    Diesel throttle system
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position
      0%: Fully open
      100%: Fully closed
    2. When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.


Data List Related to Black Smoke

NOTICE:
The Data List values in the table are the results of checking one vehicle under a specific condition (engine coolant temperature, intake air temperature, atmospheric pressure etc.). Therefore, use these values for reference only.

  1. Engine Control

    Engine Speed 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Engine Speed
    Idling: 750 to 850 rpm
    Crankshaft position sensor
    When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.

    MAP 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAP
    1. When MAP is low, there will be difficulty starting.
    2. With ignition switch ON or during idling, MAP is nearly equal to Atmosphere Pressure (standard atmospheric pressure = 101 kPa).
    When MAP is low, the following conditions are possible:
    1. Diesel throttle nearly fully closed.
    2. Intake system blocked (turbocharger system also).
    3. Exhaust system blocked.
    1. When the ignition switch is ON or the vehicle is idling, MAP (intake manifold absolute pressure) and Atmosphere Pressure are approximately equal (standard atmospheric pressure = 101 kPa).
      Above approx. 1500 rpm, the turbo becomes effective, and the pressure becomes higher than atmospheric pressure.
    2. Inspect while comparing with "Target Booster Pressure".
    3. With the accelerator fully open, if the actual Manifold Absolute Pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.
    Results of real-vehicle check:
    1. Ignition switch ON: 100 kPa
    2. Cranking: 99 kPa
    3. Idling (warm up the engine): 94 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 117 kPa
    5. Driving with the accelerator fully open at 2000 rpm: 186 kPa
    6. Driving with the accelerator fully open at 3000 rpm: 242 kPa

    MAF 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAF
    -
    1. MAF meter
    2. MAF meter circuit
    3. Intake system clogging, leaking
    4. Exhaust system clogging
    5. Turbocharger sub-assembly
    6. Leaking or clogging of turbocharger passages
    7. EGR valve does not close
    1. Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.
    2. If the value is always approximately 0 g/sec.:
      1. Mass air flow meter power source circuit is open.
      2. VG circuit is open or shorted.
      3. EVG circuit is open.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 g/sec.
    2. Cranking: 5.07 g/sec.
    3. Idling (warm up the engine): 3.87 g/sec. (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 34 g/sec.
    5. Driving with the accelerator fully open at 2000 rpm: 79 g/sec.
    6. Driving with the accelerator fully open at 3000 rpm: 138 g/sec.

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Intake Air 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Intake Air
    -
    Intake air temperature sensor.
    1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    2. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

    Coolant Temp 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Coolant Temp
    1. Engine coolant temperature is approximately equal to intake air temperature after leaving overnight. After warm-up: Engine coolant temperature is 70°C (158°F) or higher.
    2. In cases when the engine coolant temperature output is obviously higher than the actual engine coolant temperature, when it is cold, there will be difficulty starting due to problems with glow plugs or insufficient fuel injection.
    3. In cases when the engine coolant temperature sensor output is obviously lower than the actual engine coolant temperature, when it is warm, there will be difficulty starting (black smoke will also occur) due to an excess of injected fuel.
    Engine coolant temperature sensor
    1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
    2. After a long soak, the coolant temperature, intake air temperature and ambient air temperature are approximately equal.

    Engine Speed of Cyl #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Engine Speed of Cyl #1 (to #4)
    When cranking, the engine speed of each cylinder is the same under normal conditions. When a cylinder is approximately 100 rpm higher than the other cylinders, it is conceivable that the compression of that cylinder is being lost.

    HINT:
    This data is output only when the Active Test "Check the Cylinder Compression" is performed.

    -
    1. Output only when the Active Test "Check the Cylinder Compression" is performed.
    2. With this Active Test, the fuel injection is stopped.
    3. Indicates the speed of each cylinder when cranking.
      Example - Normal: "Engine speed" of all cylinders is approximately equal.
      No. 1 cylinder compression low: "Engine speed of Cyl#1" = approximately 300 rpm, "Engine speed of Cyl #2 to #4 cylinder" = approximately 200 rpm.

  2. Diesel Injection

    Target Common Rail Pressure 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Common Rail Pressure
    -
    -
    1. Inspect the (actual) fuel pressure, comparing it against the common rail target value.
    2. Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions.
    Results of real-vehicle check:
    1. Ignition switch ON: 35000 kPa
    2. Cranking: 50000 kPa
    3. Idling (warm up the engine): 35000 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 63240 kPa
    5. Running without load (3500 rpm): 72950 kPa
    6. Driving with the accelerator fully open at 2000 rpm: 138590 kPa
    7. Driving with the accelerator fully open at 3000 rpm: 183210 kPa

    Fuel Press 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Fuel Press
    1. In a stable operating condition (e.g. idling), Fuel Press is Target Common Rail Pressure +/-5000 kPa.
    2. During cranking, if Fuel Press is below 25000 kPa, there may be difficulty starting (take care as there is a response lag when the pressure rises).
    3. When Fuel Press is below 25000 kPa, rough idling will occur.
    1. If there is a fault with the fuel supply pump (lack of discharge quantity) or pressure discharge valve (will not fully close), the fuel pressure will drop. Also, a blocked fuel filter, leakage from fuel pipes, and lack of fuel will also make the fuel pressure drop.
    2. If air mixes with the fuel, the fuel pressure will shift away from the target fuel pressure.
    3. When there is a fault with the fuel supply pump, there is a possibility of lack of power, engine stall, rough idle and difficulty starting.
    1. Fuel press is the actual common rail fuel pressure.
    2. Inspect by comparing Fuel Press with Target Common Rail Pressure.
    3. The ECM uses Fuel Press for feedback control of Target Fuel Pressure via the supply pump.
      The injection amount is determined based on the injection timing and fuel pressure.
      Also, the spray pattern is selected based on the fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 kPa
    2. Cranking: 35390 kPa
    3. Idling (warm up the engine): 33640 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 62920 kPa
    5. Driving with the accelerator fully open at 2000 rpm: 134390 kPa
    6. Driving with the accelerator fully open at 3000 rpm: 178670 kPa

    Target Pump SCV Current 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Pump SCV Current
    Idling after warming up: roughly 923 to 1123 mA. When this value is large, the pump is trying to increase the fuel discharge rate.
    1. With this data, component fault not specified, use this data as a reference.
    2. If the current is 3000 mA or more, there is a possibility the suction control valve is stuck.
    1. ECU-calculated value for the suction control valve actuation target current.
    1. Value is large when a high fuel pressure is desired.
    2. When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 1008 mA
    2. Cranking: 1155 mA
    3. Running without load (2500 rpm): 1300 mA
    4. Driving with the accelerator fully open at 2000 rpm: 1233 mA
    5. Driving with the accelerator fully open at 3000 rpm: 1397 mA

    Injection Feedback Val #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Feedback Val #1 (to #4)
    1. When idling after the engine is warmed up, the fuel quantity of each fuel injector is corrected to make each cylinder engine speed equal.
    2. Cylinders more than 3 mm3/st may have a fault.

    HINT:
    Read the value after one minute of idling after warm up (engine coolant temperature above 70°C (158°F)). This value is only calculated when idling.

    1. Fault with a fuel injector or lack of compression of a cylinder with a large Injection Feedback Val.
    2. Do a compression Active Test. If there is a cylinder that is around 100 rpm more than the other cylinders, there is a possibility that the compression of that cylinder is being lost.
    3. If all the cylinder speeds are even according to the compression Active Test result, the fuel injector of the cylinder may have a fault.
    4. With fuel injector faults, other than difficulty starting, there is a possibility of rough idling, lack of power, black smoke, white smoke and knocking.
    1. When idling after warm up, the injection amount for each cylinder is corrected to optimize the difference of each cylinder engine speed.
      Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.
    2. "Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown or insufficient compression is causing poor combustion.

    Injection Volume 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Volume
    -
    -
    After warming up the engine, when Injection Volume during idling is 10 mm3/st or more, there is tendency for the injector to clog.
    Results of real-vehicle check:
    1. Cranking: 22 mm3/st (Note: Varies depending on coolant temperature)
    2. Idling (warm up the engine): 5 mm3/st
    3. Running without load (2500 rpm): 8 mm3/st
    4. Running without load (4700 rpm): 16 mm3/st
    5. Driving with the accelerator fully open at 2000 rpm: 75 mm3/st
    6. Driving with the accelerator fully open at 3000 rpm: 78 mm3/st

  3. Diesel Throttle

    Actual Throttle Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual Throttle Position
    1. When the ignition switch is turned to ON (engine stopped), the diesel throttle is fully open. When the ignition switch is turned from ON to off, the diesel throttle is fully closed temporarily.
    2. With the diesel throttle stuck almost fully closed, there is a possibility of rough idling, engine stall, black smoke, difficulty starting and lack of power.
    Diesel throttle body
    Actual Throttle Position is the closing percentage of the throttle valve.
    1. Fully closed: 100%
    2. Fully open: 0%

      HINT:
      There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).

    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: -6%
    3. Idling (warm up the engine): 93%
    4. Running without load (2500 rpm): 51%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

  4. Diesel EGR

    Target EGR Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target EGR Position
    -
    -
    1. Fully open: 100%
    2. Fully closed: 0%
    3. Used for comparison to "Actual EGR Valve Pos".
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    Actual EGR Valve Pos. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual EGR Valve Pos.
    1. Generally Actual EGR Valve Pos. = Target EGR Pos. (Fully closed = 0%, Fully open = 100%)
    2. The EGR valve Active Test can be used to check whether the Actual EGR Valve Pos. = Target EGR Pos.
    EGR valve assembly
    1. Inspect while comparing to "Target EGR Valve Pos.".
    2. Sometimes the malfunction only occurs around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    EGR Close Lrn. Status 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    EGR Close Lrn. Status
    1. "OK" means the fully closed position learning has completed normally.
    2. When NG, the learned fully closed position may be outside of the normal range.
    -
    After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed.

    EGR Close Lrn. Val. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    EGR Close Lrn. Val.
    When leaving the vehicle idling, with the EGR Close Lrn. Status OK, the normal range of EGR Close Lrn. Val. is within 0.34 to 0.70 V. In cases when EGR Close Lrn. Status is NG or EGR Close Lrn. Val. is at the maximum or minimum (0.34 to 0.70 V) of the normal range, it is possible that the EGR valve is not completely closed or a foreign object is lodged in the EGR valve seat area.
    -
    1. This value is the EGR position sensor output voltage.
    2. As the maximum and minimum settings are 0.34 V and 0.70 V, if the value becomes stuck at either of these, there is a malfunction in the lift sensor or the valve position is shifted (due to foreign matter, etc.).


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing a fuel supply pump, the ECM needs initialization (Click here).
  3. After replacing a fuel injector, the ECM needs registration .

HINT:
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


Explanation of Symptom

Black Smoke
The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with excess air fuel ratio across the entire operating range. An insufficient quantity of air, results in imperfect combustion and increased particulate (soot) emission.
When the accelerator pedal is depressed, a lot of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by MAF).
Black smoke is emitted either when:
  1. A lack of oxygen is present during combustion
  2. Too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich
1.READ OUTPUT DTC (RELATING TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output
    A
    Engine related DTCs are output
    B



B
GO TO DTC CHART
A


2.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
  1. Check the wire harness and connector connections of common rail system components.

    OK:
    The wire harnesses and connectors are connected securely.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.TAKE SNAPSHOT DURING IDLING AND 3000 RPM
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  1. Take a snapshot of the following Data List items.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    2. Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
    3. Check the Data List at idling and at 3000 rpm with no load after the engine is warmed up.


    Data Condition Idling (Engine Warmed Up) 
    Data List
    Value
    Unit
    Engine Speed
    771
    rpm
    MAP
    94
    kPa
    MAF
    3.84
    g/sec
    Target Common Rail Pressure
    35000
    kPa
    Fuel Press
    33640
    kPa
    Injection Volume
    5.15
    mm3/st
    VN Turbo Command
    57
    %
    Target EGR Position
    54.1
    %
    Actual EGR Valve Pos.
    54.1
    %
    EGR Close Lrn. Val.
    0.52
    V
    EGR Close Lrn. Status
    OK
    -
    Actual Throttle Position
    93
    %
    Throttle Close Learning Val.
    16.9
    deg
    Diesel Throttle Learn Status
    OK
    -
    Accel Position
    0.00
    %
    Injection Feedback Val #1
    0.0
    mm3/st
    Injection Feedback Val #2
    -0.5
    mm3/st
    Injection Feedback Val #3
    0.0
    mm3/st
    Injection Feedback Val #4
    0.1
    mm3/st
    Atmosphere Pressure
    100
    kPa
    Coolant Temp
    76
    °C
    Calculate Load
    14.5
    %
    Pilot 1 Injection Period
    208
    μs
    Pilot 2 Injection Period
    213
    μs

    Data Condition at 3000 rpm (Engine Warmed Up) 
    Data List
    Value
    Unit
    Engine Speed
    3000
    rpm
    Target Booster Pressure
    115.46
    kPa
    MAP
    121
    kPa
    MAF
    52.51
    g/sec
    Target Common Rail Pressure
    67500
    kPa
    Fuel Press
    67460
    kPa
    Target Pump SCV Current
    1039.0
    mA
    Injection Volume
    8.73
    mm3/st
    VN Turbo Command
    62
    %
    Target EGR Position
    42.3
    %
    Actual EGR Valve Pos.
    42.3
    %
    EGR Close Lrn. Val.
    0.52
    V
    EGR Close Lrn. Status
    OK
    -
    Actual Throttle Position
    40
    %
    Throttle Close Learning Val.
    16.9
    deg
    Diesel Throttle Learn Status
    OK
    -
    Accel Position
    14.06
    %
    Injection Feedback Val #1
    0.0
    mm3/st
    Injection Feedback Val #2
    -0.5
    mm3/st
    Injection Feedback Val #3
    0.1
    mm3/st
    Injection Feedback Val #4
    0.0
    mm3/st
    Coolant Temp
    83
    °C
    Calculate Load
    20.7
    %
    Pilot 1 Injection Period
    163
    μs
    Pilot 2 Injection Period
    182
    μs


NEXT


4.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT)


    A176220E02
  1. Check Target Pump SCV Current in the snapshot taken when the engine was idling and at 3000 rpm with no load.

    Result 
    Result
    Proceed to
    Target Pump SCV Current is below 3000 mA
    A
    Target Pump SCV Current is 3000 mA or higher
    B



B
Go to step 22
A


5.CHECK FUEL INJECTOR COMPENSATION CODE
  1. Read the fuel injector compensation codes.

    OK:
    Compensation codes stored in the ECM match the compensation codes of the installed fuel injectors.



NG
Go to step 30
OK


6.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 to #4)
  1. Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and has been idling for 1 minute.

    Result 
    Result
    Proceed to
    Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is 10 mm3/st or less
    A
    Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st
    B*
    Injection Feedback Val #1 to #4 is outside the range of +/-3 mm3/st

    HINT:
    There may be a malfunction in the corresponding cylinder.

    C

    HINT:
    *: When case "B" occurs, usually symptoms may be noticeable, such as difficult starting, rough idling, knocking or black smoke at high common rail pressure.



B
Go to step 28

C
Go to step 32
A


7.CHECK EGR VALVE ASSEMBLY
  1. Check the EGR valve assembly .



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


8.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


9.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERE PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

  1. Compare MAP to Atmosphere Pressure when the ignition switch is ON (engine stopped).

    HINT:
    1. If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
    2. Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).


    Result 
    Result
    Proceed to
    Atmosphere Pressure is different from actual atmospheric pressure
    A
    MAP is different from actual atmospheric pressure
    B
    MAP and Atmosphere Pressure have the same value
    C



B
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

A
REPLACE ECM (Click here)
C


10.READ VALUE USING INTELLIGENT TESTER (ACCEL POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.

  1. Read the value.

    Standard Value:

    Condition
    Standard Value
    Accelerator pedal released
    0%
    Accelerator pedal depressed
    100%
    Accelerator pedal released → depressed

    HINT:
    Make sure the Accel Position opening angle changes smoothly.

    0 to 100%



NG
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
OK


11.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR AND INTAKE AIR TEMP (TURBO))
  1. Connect the intelligent tester to the DLC3.

  1. Soak the engine for a long time.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air, Intake Air Temp (Turbo).

    OK:
    Intake Air is the same as Intake Air Temp (Turbo).



NG
REPLACE MALFUNCTIONING PARTS
OK


12.TAKE SNAPSHOT WHILE ACCELERATING WITH ACCELERATOR FULLY OPEN


    A176220E02
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.



  1. Take a snapshot of the following Data List items.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    2. Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.
    3. Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator fully open (obey all laws and regulations, and pay attention to driving conditions while driving the vehicle).


    A206042E01


    A206043E01


    A206044E01


    A206050E01


    Reference Values with Engine Speed at 3500 rpm (Point A) 
    Data List
    Value
    Unit
    Vehicle Speed
    44
    km/h
    Engine Speed
    3500
    rpm
    Accel Position
    99.60
    %
    Target Booster Pressure
    234.19
    kPa
    MAP
    227
    kPa
    MAF
    140.96
    g/sec
    Calculate Load
    100.0
    %
    Target Common Rail Pressure
    194350
    kPa
    Fuel Press
    189820
    kPa
    Target Pump SCV Current
    1402.8
    mA
    Injection Volume
    70.52
    mm3/st
    VN Turbo Command
    44
    %
    Actual EGR Valve Pos.
    0
    %
    Actual Throttle Position
    0
    %
    AF Lambda B1S1
    1.167
    -
    AFS Voltage B1S1
    0.27
    V


NEXT


13.CHECK SNAPSHOT (MAP AND TARGET BOOSTER PRESSURE)
  1. Check the condition of the vehicle using the snapshot.

    Result 
    Result
    Proceed to
    MAP is less than "Target Booster Pressure - 20 kPa" when accelerating with accelerator fully open
    A
    MAP and Target Booster Pressure values are almost the same
    B



B
Go to step 17
A


14.INSPECT VACUUM HOSE
  1. Check the vacuum hose connection (manifold absolute pressure sensor).

    OK:
    Vacuum hose is connected securely.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


15.CHECK INTAKE SYSTEM
  1. Check for air leakage between the turbocharger and intake manifold.



  1. Check for air leakage at intake manifold.

    HINT:
    1. Check that there are no disconnected, or leaking hoses or pipes.
    2. Check that there are no modifications made by the user.

    OK:
    No leakage.


    A189402E03



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK


16.CHECK TURBOCHARGER SUB-ASSEMBLY (MECHANICAL PROBLEM)
  1. Check the turbocharger sub-assembly .



NG
REPLACE TURBOCHARGER SUB ASSEMBLY (Click here)
OK


17.PERFORM ENGINE SPEED ACCELERATION (CHECK FOR BLACK SMOKE)
  1. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

  1. Stop the vehicle and allow the engine to idle.

  1. Fully depress the accelerator pedal for 5 seconds and then release it.*1

  1. Repeat the above procedure *1 10 times.*2

  1. Check for black smoke emission during procedures *1 and *2.

    OK:
    Black smoke is emitted less than 5 times.

    HINT:
    Even if the black smoke is very thin, count the black smoke emission if there is any visible smoke.



NG
Go to step 18
OK

END 

18.BASIC INSPECTION
  1. Check the fuel quality.

  1. Check the fuel for air.

  1. Check the fuel system for blockages.

  1. Check the air filter.

  1. Check the engine oil.

  1. Check the engine coolant.

  1. Check the engine idling speed and maximum engine speed.

  1. Check the vacuum pump.

    OK:
    Each inspection result is normal.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK


19.REPLACE CATALYTIC CONVERTER
  1. Replace the catalytic converter (Click here).


NEXT


20.CHECK INTAKE SYSTEM DEPOSIT
  1. Check carbon has accumulated on the intake manifold, cylinder head, etc. and if so, clean it off.


NEXT


21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

HINT:
Symptoms may have appeared due to carbon deposits, etc.


NEXT

END 

22.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)


    A204376E02
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) - B32-41 (PCV+)
    Always
    Below 1 Ω
    B46-2 (PCV) - B32-81 (PCV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) or B32-41 (PCV+) - Body ground
    Always
    10 kΩ or higher
    B46-2 (PCV) or B32-81 (PCV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Suction Control Valve)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


23.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
  1. Disconnect the inlet hose from the fuel supply pump.

  1. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

    OK:
    Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

    HINT:
    1. When lack of fuel, fuel pressure drops.
    2. Inspect for fuel filter clogging.
      (Check that the fuel filter is not clogged)



NG
Go to step 39
OK


24.REPLACE SUPPLY PUMP
  1. Replace the supply pump (Click here).


NEXT


25.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


26.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform supply pump initialization (Click here).


NEXT


27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

28.REPLACE FUEL INJECTOR OF ALL CYLINDERS
  1. Replace the fuel injectors (Click here).


NEXT


29.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


30.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation codes .

  1. Perform the fuel injector pilot quantity learning .


NEXT


31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

32.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

    HINT:
    1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.
    2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.


NEXT


33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

HINT:
Use this Active Test to help determine whether a cylinder has compression loss or not.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

  1. Check the engine speed during the Active Test.

    Result 
    Result
    Proceed to
    Except below
    A
    The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.
    B

    HINT:
    When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.



B
Go to step 35
A


34.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
  1. Check cylinder compression pressure .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


35.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
  1. Replace the fuel injector of the malfunctioning cylinder (Click here).


NEXT


36.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


37.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation code .

  1. Perform the fuel injector pilot quantity learning .


NEXT


38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

39.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP)
  1. Check and replace clogged the fuel pipe.


NEXT


40.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END