Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

ECD SYSTEM (for DPF) > Engine Difficult to Start or Stalling

for Preparation Click here


DESCRIPTION


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Mass Air Flow Meter 
    Component
    Mass air flow meter
    Main fault
    Decrease in performance (foreign matter is stuck)
    Symptoms
    Lack of power, black smoke
    Data List
    MAF

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Intake System 
    Component
    Intake system
    Symptom: Main fault
    1. Lack of power (No black smoke): air filter blockage, air duct is crushed/leaking
    2. Black smoke (No lack of power): Leakage between the turbo and intake manifold
    Data List
    1. MAP (inside intake air pressure)
    2. Target Booster Pressure
      When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

    Turbocharger System 
    Component
    Turbocharger system
    Main fault
    1. Air leak in the turbocharged air passage
    2. Turbo motor driver not operating well
    3. Turbocharger (turbine, bearing)
    Symptoms
    Lack of power (when vehicle starting, when heavy load)
    (Black smoke is not emitted when racing while vehicle stopped)
    Data List
    MAP (inside intake air pressure), Target Booster Pressure
    1. When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
    2. With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
    3. Atmospheric pressure increases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions.
    VN Turbo Command
    1. 0%: Vanes fully open (drive rod contracts)
    2. Over 90%: Vanes fully closed (drive rod expands and turbo operates effectively)
    Diagnostic Point
    1. Using the Active Test "Test the Turbo Charger Step Motor", check the drive rod movement.
    2. Check the drive rod movement when the ignition switch is turned from ON to off.

    Exhaust System 
    Component
    Exhaust system
    Main fault
    Blockage
    Symptoms
    Lack of power (high engine speed, when heavy load)
    Data List
    MAP (inside intake air pressure)
    When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

    Glow System 
    Component
    Glow system
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Try to measure the resistance of the glow plug

    Battery 
    Component
    Battery
    Main fault
    Battery is depleted
    Symptoms
    Difficult to start (cannot crank, crank speed is low), horn is quiet.
    Data List
    Battery Voltage
    When cranking, battery voltage is below 5 V

    Engine - 1 
    Component
    Engine
    Main fault
    Damaged, seized up
    Symptoms
    Cannot crank, crank speed is low, strange noise

    Engine - 2 
    Component
    Engine
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.

    Start System 
    Component
    Entry and start system
    Main fault
    Starter system malfunction
    Symptoms
    Difficult to start
    Data List
    Starter Signal
    1. Ignition switch (STA) operation
      ON: Starter is operating
      OFF: Starter is not operating

    Immobiliser system 
    Component
    Engine immobiliser system
    Main fault
    Engine immobiliser system (w/ Entry and Start System) / Problem Symptoms Table (Click here)
    Engine immobiliser system (w/o Entry and Start System) / Problem Symptoms Table (Click here)
    Symptoms
    Engine does not start
    Data List
    Immobiliser Communication
    1. ON: Normal
    2. OFF: GND short or immobiliser is set
    Engine Immobiliser System (w/ Entry and Start System) / Data List (Click here)
    Engine Immobiliser System (w/o Entry and Start System) / Data List (Click here)

  2. Diesel Injection

    Fuel Supply Pump 
    Component
    Fuel supply pump
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    1. The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
    2. When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Filter 
    Component
    Fuel filter
    Main fault
    Blockage
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure ".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Injector 
    Component
    Fuel injector
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

    Pressure Discharge Valve 
    Component
    Pressure discharge valve
    Main fault
    Does not completely close
    Symptoms
    Difficult to start, engine stall, rough idle, lack of power

    Injector Driver (EDU) 
    Component
    Injector Driver (EDU)
    Main fault
    Circuit fault: The fuel injector does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as fuel injector
    Diagnostic Trouble Code
    When the EDU has a fault, some DTCs may be stored.

    Fuel Pressure Sensor 
    Component
    Fuel pressure sensor
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure. (However, the value may not deviate even when a malfunction is present).
    Diagnostic Trouble Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.

    Irregular Fuel 
    Component
    Irregular fuel
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel EGR

    EGR System 
    Component
    EGR system
    Main fault
    1. Does not move smoothly
    2. Does not close completely
    Symptoms
    1. Rough idle
    2. EGR valve stuck closed: A loud turbocharger sound.
    3. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
    Data List
    Actual EGR Valve Pos., Target EGR Pos.
    1. Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
    2. Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
    3. EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).
    4. EGR valve opens to the halfway point at idling after the engine warmed up.
    EGR Close Lrn. Val., EGR Close Lrn. Status
    1. When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0.34 to 0.70 V.
    2. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0.34 to 0.70 V), it is possible that the EGR valve cannot completely close.

  4. Diesel Throttle

    Diesel Throttle System 
    Component
    Diesel throttle system
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position
      0%: Fully open
      100%: Fully closed
    2. When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.


Data List Related to Starting Trouble

NOTICE:
The Data List values in the table are the results of checking one vehicle under a specific condition (engine coolant temperature, intake air temperature, atmospheric pressure etc.). Therefore, use these values for reference only.

  1. Engine Control

    MAP 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAP
    1. When MAP is low, there will be difficulty starting.
    2. With ignition switch ON or during idling, MAP is nearly equal to Atmosphere Pressure (standard atmospheric pressure = 101 kPa).
    When MAP is low, the following conditions are possible:
    1. Diesel throttle nearly fully closed.
    2. Intake system blocked (turbocharger system also).
    3. Exhaust system blocked.
    1. When the ignition switch is ON or the vehicle is idling, MAP (intake manifold absolute pressure) and Atmosphere Pressure are approximately equal (standard atmospheric pressure = 101 kPa).
      Above approx. 1500 rpm, the turbo becomes effective, and the pressure becomes higher than atmospheric pressure.
    2. Inspect while comparing with "Target Booster Pressure".
    3. With the accelerator fully open, if the actual Manifold Absolute Pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.
    Results of real-vehicle check:
    1. Ignition switch ON: 100 kPa
    2. Cranking: 99 kPa
    3. Idling (warm up the engine): 94 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 117 kPa
    5. Driving with the accelerator fully open at 2000 rpm: 186 kPa
    6. Driving with the accelerator fully open at 3000 rpm: 242 kPa

    MAF 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAF
    -
    1. MAF meter
    2. MAF meter circuit
    3. Intake system clogging, leaking
    4. Exhaust system clogging
    5. Turbocharger sub-assembly
    6. Leaking or clogging of turbocharger passages
    7. EGR valve does not close
    1. Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.
    2. If the value is always approximately 0 g/sec.:
      1. Mass air flow meter power source circuit is open.
      2. VG circuit is open or shorted.
    3. If the value is always 200 g/sec. or more:
      1. EVG circuit is open.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 g/sec.
    2. Cranking: 5.07 g/sec.
    3. Idling (warm up the engine): 3.87 g/sec. (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 34 g/sec.
    5. Driving with the accelerator fully open at 2000 rpm: 79 g/sec.
    6. Driving with the accelerator fully open at 3000 rpm: 138 g/sec.

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Intake Air 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Intake Air
    -
    Intake air temperature sensor.
    1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    2. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

    Coolant Temp 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Coolant Temp
    1. Engine coolant temperature is approximately equal to intake air temperature after leaving overnight. After warm-up: Engine coolant temperature is 70°C (158°F) or more.
    2. In cases when the engine coolant temperature output is obviously higher than the actual engine coolant temperature, when it is cold, there will be difficulty starting due to problems with glow plugs or insufficient fuel injection.
    3. In cases when the engine coolant temperature sensor output is obviously lower than the actual engine coolant temperature, when it is warm, there will be difficulty starting (black smoke will also occur) due to an excess of injected fuel.
    Engine coolant temperature sensor
    1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
    2. After a long soak, the coolant temperature, intake air temperature and ambient air temperature are approximately equal.

    Battery Voltage 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Battery Voltage
    When cranking, in cases when Battery Voltage becomes less than 5 V, the battery is depleted.
    Battery
    If 11 V or less, characteristics of some electrical components change.
    Results of real-vehicle check:
    1. Ignition switch ON: 12 V
    2. Cranking (with engine warmed up): 10.1 V
    3. Idling (warm up the engine): 13.3 V
    4. Running without load (2500 rpm): 13.5 V
    5. Driving with the accelerator fully open at 2000 rpm: 13.3 V
    6. Driving with the accelerator fully open at 3000 rpm: 13.0 V

    Starter Signal 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Starter Signal
    Operation of ignition switch (STA)
    ON: Starter is operating
    OFF: Starter is not operating
    Entry and start system
    1. Ignition switch (STA) output:
      1. ON: Starter is operating
      2. OFF: Starter is not operating

    Engine Speed of Cyl #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Engine Speed of Cyl #1 (to #4)
    When cranking, the engine speed of each cylinder is the same under normal conditions. When a cylinder is approximately 100 rpm higher than the other cylinders, it is conceivable that the compression of that cylinder is being lost.

    HINT:
    This data is output only when the Active Test "Check the Cylinder Compression" is performed.

    -
    1. Output only when the Active Test "Check the Cylinder Compression" is performed.
    2. With this Active Test, the fuel injection is stopped.
    3. Indicates the speed of each cylinder when cranking.
      Example - Normal: "Engine speed" of all cylinders is approximately equal.
      No. 1 cylinder compression low: "Engine speed of Cyl#1" = approximately 300 rpm, "Engine speed of Cyl #2 to #4 cylinder" = approximately 200 rpm.

    Immobiliser Communication 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Immobiliser Communication
    Engine Immobiliser System (w/ Entry and Start System) / Data List (Click here)
    Engine Immobiliser System (w/o Entry and Start System) / Data List (Click here)
    Engine Immobiliser System (w/ Entry and Start System) / Problem Symptoms Table (Click here)
    Engine Immobiliser System (w/o Entry and Start System) / Problem Symptoms Table (Click here)
    When there is a malfunction in the immobiliser system (w/ Entry and Start System), a DTC is stored (Click here)
    When there is a malfunction in the immobiliser system (w/o Entry and Start System), a DTC is stored (Click here)

  2. Diesel Injection

    Target Common Rail Pressure 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Common Rail Pressure
    -
    -
    1. Inspect the (actual) fuel pressure, comparing it against the common rail target value.
    2. Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions.
    Results of real-vehicle check:
    1. Ignition switch ON: 35000 kPa
    2. Cranking: 50000 kPa
    3. Idling (warm up the engine): 35000 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 63240 kPa
    5. Running without load (3500 rpm): 72950 kPa
    6. Driving with the accelerator fully open at 2000 rpm: 138590 kPa
    7. Driving with the accelerator fully open at 3000 rpm: 183210 kPa

    Fuel Press 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Fuel Press
    1. In a stable operating condition (e.g. idling), Fuel Press is Target Common Rail Pressure +/-5000 kPa.
    2. During cranking, if Fuel Press is below 25000 kPa, there may be difficulty starting (take care as there is a response lag when the pressure rises).
    3. When Fuel Press is below 25000 kPa, rough idling will occur.
    1. If there is a fault with the fuel supply pump (lack of discharge quantity) or pressure discharge valve (will not fully close), the fuel pressure will drop. Also, a blocked fuel filter, leakage from fuel pipes, and lack of fuel will also make the fuel pressure drop.
    2. If air mixes with the fuel, the fuel pressure will shift away from the target fuel pressure.
    3. When there is a fault with the fuel supply pump, there is a possibility of lack of power, engine stall, rough idle and difficulty starting.
    1. Fuel press is the actual common rail fuel pressure.
    2. Inspect by comparing Fuel Press with Target Common Rail Pressure.
    3. The ECM uses Fuel Press for feedback control of Target Fuel Pressure via the supply pump.
      The injection amount is determined based on the injection timing and fuel pressure.
      Also, the spray pattern is selected based on the fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 kPa
    2. Cranking: 35390 kPa
    3. Idling (warm up the engine): 33640 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 62920 kPa
    5. Driving with the accelerator fully open at 2000 rpm: 134390 kPa
    6. Driving with the accelerator fully open at 3000 rpm: 178670 kPa

    Target Pump SCV Current 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Pump SCV Current
    Idling after warming up: roughly 923 to 1123 mA. When this value is large, the pump is trying to increase the fuel discharge rate.
    1. With this data, component fault not specified, use this data as a reference.
    2. If the current is 3000 mA or more, there is a possibility the suction control valve is stuck.
    1. ECU-calculated value for the suction control valve actuation target current.
    1. Value is large when a high fuel pressure is desired.
    2. When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 1008 mA
    2. Cranking: 1155 mA
    3. Running without load (2500 rpm): 1300 mA
    4. Driving with the accelerator fully open at 2000 rpm: 1233 mA
    5. Driving with the accelerator fully open at 3000 rpm: 1397 mA

    Injection Feedback Val #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Feedback Val #1 (to #4)
    1. When idling after the engine is warmed up, the fuel quantity of each fuel injector is corrected to make each cylinder engine speed equal.
    2. Cylinders more than 3 mm3/st may have a fault.

    HINT:
    Read the value after one minute of idling after warm up (engine coolant temperature above 70°C (158°F)). This value is only calculated when idling.

    1. Fault with a fuel injector or lack of compression of a cylinder with a large Injection Feedback Val.
    2. Do a compression Active Test. If there is a cylinder that is around 100 rpm more than the other cylinders, there is a possibility that the compression of that cylinder is being lost.
    3. If all the cylinder speeds are even according to the compression Active Test result, the fuel injector of the cylinder may have a fault.
    4. With fuel injector faults, other than difficulty starting, there is a possibility of rough idling, lack of power, black smoke, white smoke and knocking.
    1. When idling after warm up, the injection amount for each cylinder is corrected to optimize the difference of each cylinder engine speed.
      Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.
    2. "Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown or insufficient compression is causing poor combustion.

    Injection Volume 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Volume
    -
    -
    After warming up the engine, when Injection Volume during idling is 10 mm3/st or more, there is tendency for the injector to clog.
    Results of real-vehicle check:
    1. Cranking: 22 mm3/st (Note: Varies depending on coolant temperature)
    2. Idling (warm up the engine): 5 mm3/st
    3. Running without load (2500 rpm): 8 mm3/st
    4. Running without load (4700 rpm): 16 mm3/st
    5. Driving with the accelerator fully open at 2000 rpm: 75 mm3/st
    6. Driving with the accelerator fully open at 3000 rpm: 78 mm3/st

  3. Diesel Throttle

    Actual Throttle Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual Throttle Position
    1. When the ignition switch is turned to ON (engine stopped), the diesel throttle is fully open. When the ignition switch is turned from ON to off, the diesel throttle is fully closed temporarily.
    2. With the diesel throttle stuck almost fully closed, there is a possibility of rough idling, engine stall, black smoke, difficulty starting and lack of power.
    Diesel throttle body
    Actual Throttle Position is the closing percentage of the throttle valve.
    1. Fully closed: 100%
    2. Fully open: 0%

      HINT:
      There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).

    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: -6%
    3. Idling (warm up the engine): 93%
    4. Running without load (2500 rpm): 51%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

  4. Diesel EGR

    Target EGR Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target EGR Position
    -
    -
    1. Fully open: 100%
    2. Fully closed: 0%
    3. Used for comparison to "Actual EGR Valve Pos".
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    Actual EGR Valve Pos. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual EGR Valve Pos.
    1. Generally Actual EGR Valve Pos. = Target EGR Pos. (Fully closed = 0%, Fully open = 100%)
    2. The EGR valve Active Test can be used to check whether the Actual EGR Valve Pos. = Target EGR Pos.
    EGR valve assembly
    1. Inspect while comparing to "Target EGR Valve Pos.".
    2. Sometimes the malfunction only occurs around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    EGR Close Lrn. Status 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    EGR Close Lrn. Status
    1. "OK" means the fully closed position learning has completed normally.
    2. When NG, the learned fully closed position may be outside of the normal range.
    -
    After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed.

    EGR Close Lrn. Val. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    EGR Close Lrn. Val.
    When leaving the vehicle idling, with the EGR Close Lrn. Status OK, the normal range of EGR Close Lrn. Val. is within 0.34 to 0.70 V. In cases when EGR Close Lrn. Status is NG or EGR Close Lrn. Val. is at the maximum or minimum (0.34 to 0.70 V) of the normal range, it is possible that the EGR valve is not completely closed or a foreign object is lodged in the EGR valve seat area.
    -
    1. This value is the EGR position sensor output voltage.
    2. As the maximum and minimum settings are 0.34 V and 0.70 V, if the value becomes stuck at either of these, there is a malfunction in the lift sensor or the valve position is shifted (due to foreign matter, etc.).


Actual Examples of Malfunction

HINT:
  1. The purpose of the following examples is help you to understand the relationship between each Data List item when a certain malfunction occurs. Understanding this relationship helps you to find the real root cause easier.
  2. The following are examples of actual malfunctions of a common rail diesel engine.
  3. Use them for reference when diagnosing malfunctions.
  4. These are not data of the RAV4 2AD-FTV.



  1. Fuel is not being supplied to supply pump (Low pressure fuel line clogged)


    A183882E04



  2. Fuel is not being injected (Injectors are leaking)


    A183884E05



  3. Fuel is not being injected (EDU circuit malfunction)


    A183885E01



  4. Fuel supply pump malfunction (Suction control valve momentarily sticking)


    A183888E02



  5. Increased opening delay of injectors (Internal contamination)


    A183889E04


INSPECTION PROCEDURE


Explanation of Symptom

Starting Trouble
For good starting it is essential to have:
  1. Sufficient cranking speed.
  2. Properly operating engine preheating system.
  3. Good quality fuel.
The fuel is ignited by the heat which is generated with compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is leaking, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the fuel injector is open.

Trouble Area Chart According to Problem Cause

A210593E01


A183464E01

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  3. After replacing a fuel injector, the ECM needs registration .

HINT:
  1. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.

1.CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

    Result 
    Result
    Proceed to
    Does not crank at all.
    A
    Low cranking speed.

    HINT:
    When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.

    B
    Cranking is OK.
    C



B
CHECK BATTERY CONDITION

C
Go to step 8
A


2.CHECK BATTERY CONDITION
  1. Check the battery condition .



NG
REPLACE BATTERY
OK


3.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Check if the normal starting screen appears (check whether communication with the ECM is possible).

    HINT:
    Use a tester that is able to communicate with other vehicles.

    OK:
    Communication is possible (vehicle can be recognized).



NG
GO TO ECM POWER SOURCE CIRCUIT (Click here)
OK


4.READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Clutch Switch.

  1. Read the value displayed on the tester.

    Standard Value:

    Tester Display
    Condition
    Specified Condition
    Clutch Switch
    Clutch pedal depressed
    ON

    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPLACE CLUTCH START SWITCH (Click here)
A


5.READ ALL OUTPUT DTCS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Utility / All Codes.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTCs related to engine are output
    B



B
GO TO RELATED DTC (Click here)
A


6.INSPECT ENTRY AND START SYSTEM (FOR ENTRY AND START SYSTEM)
  1. Check if the "Door Control Transmitter" function of each key functions properly.

    HINT:
    1. Check if the engine starts properly with another key.
    2. If the doors cannot be opened/closed by using the "Door Control Transmitter" function of the key, the battery inside the key may be depleted. In such a case, the engine cannot be started by pushing the engine switch.
    3. When the door control transmitter battery is depleted, the engine can only be started by holding the door control transmitter against the engine switch.
    4. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If any optional components are installed, remove them and perform the operation check.
      Near broadcasting stations, large screens, airports, transformer stations, gasoline stations, etc., the door control transmitter may not operate due to electric wave interference.


NEXT


7.INSPECT STARTER SIGNAL CIRCUIT OR CRANKING HOLDING FUNCTION CIRCUIT

HINT:
Check that "Starter Signal" in the Data List changes to ON when the engine is started.

  1. Inspect the starter signal circuit (w/o Entry and Start System) (Click here).

  1. Inspect the cranking holding function circuit (w/ Entry and Start System) (Click here).


NEXT

END 

8.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
  1. Check if the fuel level is low.
    Result 
    Result
    Proceed to
    The indicator (fuel warning light) is not illuminated
    A
    The indicator (fuel warning light) is illuminated
    B



B
Go to step 46
A


9.CHECK INITIALIZATION (FUEL SUPPLY PUMP)
  1. When the engine does not start or another problem such as rough idling is present, perform initialization and check to see if the problem symptoms disappear. If the problem symptoms do not disappear, perform the next procedure.

    HINT:
    When replacing the ECM, the supply pump initialization must be performed (Click here).


NEXT


10.READ OUTPUT DTC (RELATED TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTCs related to engine are output
    B



B
REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT (Click here)
A


11.TAKE SNAPSHOT DURING STARTING AND IDLING
A176220E02

A206046E01


A206047E01


A206048E01

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  1. Take a snapshot of the following Data List items with the intelligent tester during "ignition switch ON (5 seconds) → Starting → Idling (10 seconds)".

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    2. When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature 70°C (158°F) or more) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.
    3. Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.

Data List
Starter Signal
Engine Speed
Fuel Press
Target Common Rail Pressure
Target Pump SCV Current
Injection Volume
Main Injection Period
Inj. FB Vol. for Idle
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Battery Voltage
Actual EGR Valve Pos.
Target EGR Position
Actual Throttle Position
MAF
Target Booster Pressure
MAP

Reference Values during Engine Start (Point A) 
Data List
Value
Unit
Starter Signal
ON
-
Engine Speed
366
rpm
Fuel Press
35390
kPa
Target Common Rail Pressure
50000
kPa
Injection Volume
22.57
mm3/st
Main Injection Period
682
μs
Inj. FB Vol. for Idle
0.70
mm3/st
Battery Voltage
10.1
V
Target EGR Position
0
%
Actual EGR Valve Pos.
0
%
Actual Throttle Position
-6
%
MAF
5.07
g/sec
MAP
99
kPa
Target Boost Pressure
101.34
kPa
Coolant Temp
75
°C

Data Condition at Idling (Engine Warmed Up) 
Data List
Value
Unit
Engine Speed
771
rpm
Target Booster Pressure
92.69
kPa
MAP
94
kPa
MAF
3.87
g/sec
Target Common Rail Pressure
35000
kPa
Fuel Press
33640
kPa
Injection Volume
5.15
mm3/st
Actual EGR Valve Pos.
54.1
%
Actual Throttle Position
93
%
Injection Feedback Val #1
0.0
mm3/st
Injection Feedback Val #2
-0.5
mm3/st
Injection Feedback Val #3
0.0
mm3/st
Injection Feedback Val #4
0.1
mm3/st
Target EGR Position
54.1
%
Coolant Temp
76
°C

HINT:
Actual Examples of Malfunction (See "Diagnostic Help" menu)
  1. Starting is not possible
    1. Fuel is not supplied to supply pump.
      Fuel Press: Approximately 1000 kPa or less during cranking.
    2. Fuel is not being injected due to EDU circuit malfunction.
      Fuel Press: 80000 to 90000 kPa during cranking.
    3. Air in injectors.
      Fuel Press: 60000 to 70000 kPa during cranking.
  1. Cranking time is long
    1. Suction control valve is stuck.
      Target Pump SCV Current intermittently reaches 3000 mA or more. The suction control valve plunger intermittently becomes stuck. If there is difficulty starting when the engine is cold, cool the engine and inspect it.
    2. Injector clogging or internal contamination:
      Injection Feedback Val # of one or more of the cylinders is 3 mm3/st or more.
      Injection Feedback Val # can be read when the engine is idling after being warmed up.


NEXT


12.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT)
  1. Check Target Pump SCV Current in the snapshot taken when the engine was starting.
    Result 
    Result
    Proceed to
    Target Pump SCV Current is 3000 mA or more
    A
    Target Pump SCV Current is less than 3000 mA
    B



A
Go to step 15
B


13.CHECK SNAPSHOT (FUEL PRESS)
  1. Check Fuel Press in the snapshot taken when the engine was starting.

    Result 
    Result
    Proceed to
    2 seconds after Starter Signal turns from OFF to ON, Fuel Press is less than 25000 kPa

    HINT:
    As long as the fuel pressure remains below 5000 kPa, the ECM stops sending the injection open signal (IJT) to the EDU, and then the actual injection duration remains 0 microseconds.

    A
    2 seconds after Starter Signal turns from OFF to ON, Fuel Press is 50000 kPa or more
    B
    Except above
    C

    HINT:
    1. Fuel pressure is about 20000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or more.
    2. Fuel pressure increases rapidly during cranking.



B
Go to step 38

C
Go to step 26
A


14.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)


    A203995
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.*1

    NOTICE:
    1. Hand pump pumping speed: Maximum of 2 strokes/second.
    2. Be sure to push the hand pump with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. Just after starting the engine, visually check for fuel leaks from the supply pump, fuel injector, common rail, and the fuel pipes in high-pressure areas.
    2. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    3. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    4. Use a fully-charged battery.

    1. When the engine can be started, proceed to step *2.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to step *1). Then start the engine.

  1. Turn the ignition switch off.*2

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.*3

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*4

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*5



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.*6


    A192848E01

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed. Proceed to step *8.

    2. If any DTCs are output, proceed to step *7.

  1. Clear DTCs (Click here).*7

  1. Repeat steps *3 to*6.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.*8

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    Result 
    Result
    Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 25000 kPa 2 seconds after the starter signal changes from OFF to ON.
    B
    Except above
    A



B
Go to step 16
A

END 

15.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)


    A204376E02
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) - B32-41 (PCV+)
    Always
    Below 1 Ω
    B46-2 (PCV) - B32-81 (PCV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) or B32-41 (PCV+) - Body ground
    Always
    10 kΩ or higher
    B46-2 (PCV) or B32-81 (PCV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Suction Control Valve)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



OK
Go to step 17

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT COMMON RAIL ASSEMBLY
  1. Inspect the common rail assembly .



NG
Go to step 23
OK


17.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
  1. Disconnect the inlet hose from the fuel supply pump.

  1. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

    OK:
    Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

    HINT:
    1. When there is a lack of fuel, fuel pressure drops.
    2. Inspect for fuel filter clogging (check that the fuel filter is not clogged).



NG
Go to step 45
OK


18.REPLACE FUEL SUPPLY PUMP
  1. Replace the fuel supply pump (Click here).


NEXT


19.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


20.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


21.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    Result 
    Result
    Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 25000 kPa 2 seconds after the starter signal changes from OFF to ON.
    B
    Except above
    A



B
Go to step 22
A

END 

22.INSPECT FUEL INJECTOR (INSPECTION FOR VALVE CLOSING PROBLEM)
  1. Remove the glow plug assembly for all the cylinders (Click here).

  1. Visually check if there is fuel on the glow plugs.

    HINT:
    1. If there is fuel on a glow plug, fuel may be leaking from a fuel injector.
    2. After replacing a fuel injector, make sure that the common rail pressure (fuel pressure) is within +/-5000 kPa of the target fuel pressure while cranking the engine.
    3. If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.

    Result 
    Result
    Proceed to
    No fuel on glow plugs
    A
    Fuel on glow plugs
    B

  1. Install the glow plug assembly (Click here).



B
Go to step 28
A


23.REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


24.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


25.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    Result 
    Result
    Proceed to
    The engine cannot be started or the engine can be started but Fuel Press is less than 25000 kPa 2 seconds after the starter signal changes from OFF to ON.
    B
    Except above
    A



B
Go to step 28
A

END 

26.INSPECT INJECTOR COMPENSATION CODE
  1. Read the injector compensation code .

    OK:
    Compensation codes stored in the ECM match compensation codes of the installed fuel injectors.



NG
REGISTER FUEL INJECTOR COMPENSATION CODE
OK


27.CHECK ENGINE STARTING CONDITION
  1. Check whether the engine can be started.

    HINT:
    If there are deposits in the injectors and they are left for a long time, the injectors for all the cylinders may become stuck.


    Result 
    Result
    Proceed to
    The engine can be started.
    A
    There is no initial combustion even when the engine can be cranked.
    B



B
Go to step 41
A


28.CHECK DATA LIST


    A176220E02
  1. Check Injection Feedback Val # and Injection Volume in the snapshot taken when the engine was idling.

    Result 
    Result
    Proceed to
    Injection Feedback Val #1 to #4 is outside the range of +/-3 mm3/st

    HINT:
    There may be a malfunction in the corresponding cylinder.

    A
    Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st
    B*
    Injection Feedback Val #1 to #4 is within the range +/-3 mm3/st and Injection Volume is 10 mm3/st or less
    C

    HINT:
    *: When case "B" occurs, usually symptoms may be noticeable, such as difficult starting, rough idling, knocking or black smoke at high common rail pressure.



B
Go to step 41

C
Go to step 33
A


29.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

HINT:
  1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.
  2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.


NEXT


30.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

HINT:
Use this Active Test to help determine whether a cylinder has compression loss or not.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

  1. Check the engine speed during the Active Test.

    OK:
    The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.

    HINT:
    When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a loss of compression in that cylinder.



OK
Go to step 32

NG
Go to step 31

31.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

HINT:
Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".

  1. Check the cylinder compression pressure .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


32.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

HINT:
The injector is determined to be faulty as the corresponding cylinder is malfunctioning, but has no compression loss.

  1. Replace the fuel injector (Click here).



NEXT
Go to step 42

33.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
  1. Check the temperature when starting trouble occurs.


Result 
Result
Proceed to
Difficult to start only for cold engine.
A
Difficult to start both for cold and warmed up engine.
B


B
Go to step 36
A


34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


35.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
A197252
  1. Disconnect the glow plug wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Glow plug terminal - Body ground
    20°C (68°F)
    Approximately 1.0 Ω

    HINT:
    If any of the glow plugs has an open circuit, the engine power will be insufficient only when the engine is cold.

    NOTICE:
    1. Exercise extreme care not to damage the glow plug pipes. Damaging them could cause an open circuit or shorten the life of the glow plugs.
    2. Keep the glow plugs free of oil and fuel while cleaning.
    3. Wipe any oil off of the terminal and Bakelite washer with a clean, dry cloth during inspection.
    4. Do not apply higher than 11 V to the glow plugs as it may cause an open circuit.



NG
REPLACE GLOW PLUG ASSEMBLY (Click here)
OK


36.CHECK FUEL QUALITY
  1. Check that fuel with a low cetane number is used.


NEXT


37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check whether the difficulty starting has been successfully repaired by starting the engine.


NEXT

END 

38.CHECK SNAPSHOT

HINT:
When all Data List values are OK and Fuel Press is higher than Target Common Rail Pressure, perform the following inspection.


NEXT


39.INSPECT INJECTOR DRIVER (EDU POWER SOURCE)


    A204910E02
  1. Disconnect the injector driver (EDU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B102-2 (+B) - B102-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Injector Driver (EDU))

  1. Reconnect the injector driver (EDU) connector.



NG
GO TO INJECTOR CIRCUIT (Click here)
OK


40.INSPECT FUEL INJECTOR

HINT:
If there is no initial combustion during cranking, there may be air in the injectors.


NEXT

END 

41.REPLACE FUEL INJECTORS OF ALL CYLINDERS
  1. Replace the fuel injectors (Click here).


NEXT


42.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


43.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation codes .

  1. Perform the fuel injector pilot quantity learning .


NEXT


44.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    OK:
    The engine can be started but Fuel Press is 25000 kPa or higher 2 seconds after the starter signal changes from OFF to ON.


NEXT

END 

45.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP)
  1. Check and replace the clogged fuel pipe.



NEXT
Go to step 47

46.ADD FUEL
  1. Add fuel.


NEXT


47.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


48.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

  1. Start the engine.

  1. Read the Fuel Press values while cranking and idling the engine.

    OK:
    The engine can be started but Fuel Press is 25000 kPa or higher 2 seconds after the starter signal changes from OFF to ON.


NEXT

END