Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

ECD SYSTEM (for DPF) > Rough Idling or Excessive Engine Vibrations

for Preparation Click here


DESCRIPTION


Malfunction Condition
Main Trouble Area
Related Trouble Area
  1. Rough idling or shuddering due to abnormal combustion
  2. Shuddering when starting vehicle due to clutch system malfunctions
  1. Fuel injector malfunctions
    1. Fuel injector sliding malfunction
    2. Fuel injector stuck closed
    3. Fuel injector stuck open
    4. Deposit in fuel injector
    5. Fuel injector circuit malfunction
  2. Clutch system malfunctions
    1. Clutch system (shuddering when starting)
  1. Fuel injector compensation code
  2. Fuel leak
  3. Engine mounting insulator
  4. Intake air system leakage
  5. Intake air system blockage
  6. EGR system
  7. Throttle valve system
  8. Fuel supply pump
  9. Low quality fuel
  10. Vehicle modifications
  11. Fuel filter air bleed problem
  12. Accessory problem (A/C, generator, etc.)
  13. ECM

HINT:
  1. Rough idling and excessive engine vibrations are checked in this troubleshooting procedure.
  2. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
  3. Check that the vehicle has not been modified in any way prior to the vehicle inspection.


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Mass Air Flow Meter 
    Component
    Mass air flow meter
    Main fault
    Decrease in performance (foreign matter is stuck)
    Symptoms
    Lack of power, black smoke
    Data List
    MAF

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Glow System 
    Component
    Glow system
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Try to measure the resistance of the glow plug

    Engine 
    Component
    Engine
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.

  2. Diesel Injection

    Fuel Supply Pump 
    Component
    Fuel supply pump
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    1. The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
    2. When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Filter 
    Component
    Fuel filter
    Main fault
    Blockage
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Injector 
    Component
    Fuel injector
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

    Pressure Discharge Valve 
    Component
    Pressure discharge valve
    Main fault
    Does not completely close
    Symptoms
    Difficult to start, engine stall, rough idle, lack of power

    Injector Driver (EDU) 
    Component
    Injector Driver (EDU)
    Main fault
    Circuit fault: The fuel injector does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as fuel injector
    Diagnostic Trouble Code
    When the EDU has a fault, some DTCs may be stored.

    Fuel Pressure Sensor 
    Component
    Fuel pressure sensor
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (however, the value may not deviate even when a malfunction is present).
    Diagnostic Trouble Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.

    Irregular Fuel 
    Component
    Irregular fuel
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel EGR

    EGR System 
    Component
    EGR system
    Main fault
    1. Does not move smoothly
    2. Does not close completely
    Symptoms
    1. Rough idle
    2. EGR valve stuck closed: A loud turbocharger sound.
    3. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).
    Data List
    Actual EGR Valve Pos., Target EGR Pos.
    1. Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
    2. Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
    3. EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).
    4. EGR valve opens to the halfway point at idling after the engine is warmed up.
    EGR Close Lrn. Val., EGR Close Lrn. Status
    1. When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0.34 to 0.70 V.
    2. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0.34 to 0.70 V), it is possible that the EGR valve cannot completely close.

  4. Diesel Throttle

    Diesel Throttle System 
    Component
    Diesel throttle system
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position
      0%: Fully open
      100%: Fully closed
    2. When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.


Data List Related to Rough Idling

NOTICE:
The Data List values in the table are the results of checking one vehicle under a specific condition (engine coolant temperature, intake air temperature, atmospheric pressure etc.). Therefore, use these values for reference only.

  1. Engine Control

    Engine Speed 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Engine Speed
    Idling: 750 to 850 rpm
    Crankshaft position sensor
    When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.

    MAF 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAF
    -
    1. MAF meter
    2. MAF meter circuit
    3. Intake system clogging, leaking
    4. Exhaust system clogging
    5. Turbocharger sub-assembly
    6. Leaking or clogging of turbocharger passages
    7. EGR valve does not close
    1. Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.
    2. If the value is always approximately 0 g/sec.:
      1. Mass air flow meter power source circuit is open.
      2. VG circuit is open or shorted.
    3. If the value is always 200 g/sec. or more:
      1. EVG circuit is open.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 g/sec.
    2. Cranking: 5.07 g/sec.
    3. Idling (warm up the engine): 3.87 g/sec. (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 34 g/sec.
    5. Driving with the accelerator fully open at 2000 rpm: 79 g/sec.
    6. Driving with the accelerator fully open at 3000 rpm: 138 g/sec.

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Intake Air 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Intake Air
    -
    Intake air temperature sensor.
    1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    2. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

    Coolant Temp 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Coolant Temp
    1. Engine coolant temperature is approximately equal to intake air temperature after leaving overnight. After warm-up: Engine coolant temperature is 60°C (140°F) or higher.
    2. In cases when the engine coolant temperature output is obviously higher than the actual engine coolant temperature, when it is cold, there will be difficulty starting due to problems with glow plugs or insufficient fuel injection.
    3. In cases when the engine coolant temperature sensor output is obviously lower than the actual engine coolant temperature, when it is warm, there will be difficulty starting (black smoke will also occur) due to an excess of injected fuel.
    Engine coolant temperature sensor
    1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
    2. After a long soak, the coolant temperature, intake air temperature and ambient air temperature are approximately equal.

    Engine Speed of Cyl #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Engine Speed of Cyl #1 (to #4)
    When cranking, the engine speed of each cylinder is the same under normal conditions. When a cylinder is approximately 100 rpm higher than the other cylinders, it is conceivable that the compression of that cylinder is being lost.

    HINT:
    This data is output only when the Active Test "Check the Cylinder Compression" is performed.

    -
    1. Output only when the Active Test "Check the Cylinder Compression" is performed.
    2. With this Active Test, the fuel injection is stopped.
    3. Indicates the speed of each cylinder when cranking.
      Example - Normal: "Engine speed" of all cylinders is approximately equal.
      No. 1 cylinder compression low: "Engine speed of Cyl#1" = approximately 300 rpm, "Engine speed of Cyl #2 to #4 cylinder" = approximately 200 rpm.

  2. Diesel Injection

    Target Common Rail Pressure 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Common Rail Pressure
    -
    -
    1. Inspect the (actual) fuel pressure, comparing it against the common rail target value.
    2. Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions.
    Results of real-vehicle check:
    1. Ignition switch ON: 35000 kPa
    2. Cranking: 50000 kPa
    3. Idling (warm up the engine): 35000 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 63240 kPa
    5. Running without load (3500 rpm): 72950 kPa
    6. Driving with the accelerator fully open at 2000 rpm: 138590 kPa
    7. Driving with the accelerator fully open at 3000 rpm: 183210 kPa

    Fuel Press 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Fuel Press
    1. In a stable operating condition (e.g. idling), Fuel Press is Target Common Rail Pressure +/-5000 kPa.
    2. During cranking, if Fuel Press is below 25000 kPa, there may be difficulty starting (take care as there is a response lag when the pressure rises).
    3. When Fuel Press is below 25000 kPa, rough idling will occur.
    1. If there is a fault with the fuel supply pump (lack of discharge quantity) or pressure discharge valve (will not fully close), the fuel pressure will drop. Also, a blocked fuel filter, leakage from fuel pipes, and lack of fuel will also make the fuel pressure drop.
    2. If air mixes with the fuel, the fuel pressure will shift away from the target fuel pressure.
    3. When there is a fault with the fuel supply pump, there is a possibility of lack of power, engine stall, rough idle and difficulty starting.
    1. Fuel press is the actual common rail fuel pressure.
    2. Inspect by comparing Fuel Press with Target Common Rail Pressure.
    3. The ECM uses Fuel Press for feedback control of Target Fuel Pressure via the supply pump.
      The injection amount is determined based on the injection timing and fuel pressure.
      Also, the spray pattern is selected based on the fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 kPa
    2. Cranking: 35390 kPa
    3. Idling (warm up the engine): 33640 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 62920 kPa
    5. Driving with the accelerator fully open at 2000 rpm: 134390 kPa
    6. Driving with the accelerator fully open at 3000 rpm: 178670 kPa

    Target Pump SCV Current 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Pump SCV Current
    Idling after warming up: roughly 923 to 1123 mA. When this value is large, the pump is trying to increase the fuel discharge rate.
    1. With this data, component fault not specified, use this data as a reference.
    2. If the current is 3000 mA or more, there is a possibility the suction control valve is stuck.
    1. ECU-calculated value for the suction control valve actuation target current.
    1. Value is large when a high fuel pressure is desired.
    2. When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 1008 mA
    2. Cranking: 1155 mA
    3. Running without load (2500 rpm): 1300 mA
    4. Driving with the accelerator fully open at 2000 rpm: 1233 mA
    5. Driving with the accelerator fully open at 3000 rpm: 1397 mA

    Injection Feedback Val #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Feedback Val #1 (to #4)
    1. When idling after the engine is warmed up, the fuel quantity of each fuel injector is corrected to make each cylinder engine speed equal.
    2. Cylinders more than 3 mm3/st may have a fault.

    HINT:
    Read the value after one minute of idling after warm up (engine coolant temperature above 70°C (158°F)). This value is only calculated when idling.

    1. Fault with a fuel injector or lack of compression of a cylinder with a large Injection Feedback Val.
    2. Do a compression Active Test. If there is a cylinder that is around 100 rpm more than the other cylinders, there is a possibility that the compression of that cylinder is being lost.
    3. If all the cylinder speeds are even according to the compression Active Test result, the fuel injector of the cylinder may have a fault.
    4. With fuel injector faults, other than difficulty starting, there is a possibility of rough idling, lack of power, black smoke, white smoke and knocking.
    1. When idling after warm up, the injection amount for each cylinder is corrected to optimize the difference of each cylinder engine speed.
      Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.
    2. "Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown or insufficient compression is causing poor combustion.

    Injection Volume 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Volume
    -
    -
    After warming up the engine, when Injection Volume during idling is 10 mm3/st or more, there is tendency for the injector to clog.
    Results of real-vehicle check:
    1. Cranking: 22 mm3/st (Note: Varies depending on coolant temperature)
    2. Idling (warm up the engine): 5 mm3/st
    3. Running without load (2500 rpm): 8 mm3/st
    4. Running without load (4700 rpm): 16 mm3/st
    5. Driving with the accelerator fully open at 2000 rpm: 75 mm3/st
    6. Driving with the accelerator fully open at 3000 rpm: 78 mm3/st

  3. Diesel Throttle

    Actual Throttle Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual Throttle Position
    1. When the ignition switch is turned to ON (engine stopped), the diesel throttle is fully open. When the ignition switch is turned from ON to off, the diesel throttle is fully closed temporarily.
    2. With the diesel throttle stuck almost fully closed, there is a possibility of rough idling, engine stall, black smoke, difficulty starting and lack of power.
    Diesel throttle body
    Actual Throttle Position is the closing percentage of the throttle valve.
    1. Fully closed: 100%
    2. Fully open: 0%

      HINT:
      There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).

    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: -6%
    3. Idling (warm up the engine): 93%
    4. Running without load (2500 rpm): 51%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

  4. Diesel EGR

    Target EGR Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target EGR Position
    -
    -
    1. Fully open: 100%
    2. Fully closed: 0%
    3. Used for comparison to "Actual EGR Valve Pos".
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    Actual EGR Valve Pos. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual EGR Valve Pos.
    1. Generally Actual EGR Valve Pos. = Target EGR Pos. (Fully closed = 0%, Fully open = 100%)
    2. The EGR valve Active Test can be used to check whether the Actual EGR Valve Pos. = Target EGR Pos.
    EGR valve assembly
    1. Inspect while comparing to "Target EGR Valve Pos.".
    2. Sometimes the malfunction only occurs around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    EGR Close Lrn. Status 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    EGR Close Lrn. Status
    1. "OK" means the fully closed position learning has completed normally.
    2. When NG, the learned fully closed position may be outside of the normal range.
    -
    After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed.

    EGR Close Lrn. Val. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    EGR Close Lrn. Val.
    When leaving the vehicle idling, with the EGR Close Lrn. Status OK, the normal range of EGR Close Lrn. Val. is within 0.34 to 0.70 V. In cases when EGR Close Lrn. Status is NG or EGR Close Lrn. Val. is at the maximum or minimum (0.34 to 0.70 V) of the normal range, it is possible that the EGR valve is not completely closed or a foreign object is lodged in the EGR valve seat area.
    -
    1. This value is the EGR position sensor output voltage.
    2. As the maximum and minimum settings are 0.34 V and 0.70 V, if the value becomes stuck at either of these, there is a malfunction in the lift sensor or the valve position is shifted (due to foreign matter, etc.).


Actual Examples of Malfunction

HINT:
  1. The purpose of the following examples is help you to understand the relationship between each Data List item when a certain malfunction occurs. Understanding this relationship helps you to find the real root cause easier.
  2. The following are examples of actual malfunctions of a common rail diesel engine.
  3. Use them for reference when diagnosing malfunctions.
  4. These are not data of the RAV4 2AD-FTV.



  1. Supply pump malfunction (suction control valve momentarily sticking)


    A186085E03



  2. Fuel injectors sticking


    A188772E03


INSPECTION PROCEDURE

NOTICE:
  1. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  2. After replacing a fuel injector, the ECM needs registration .

HINT:
Before troubleshooting, conduct the following:
  1. (a) Check the fuel quality.
  2. (b) Check the fuel for air.
  3. (c) Check the fuel system for blockages.
  4. (d) Check the air filter.
  5. (e) Check the engine oil.
  6. (f) Check the engine coolant.
  7. (g) Check the engine idling speed and maximum engine speed.
  8. (h) Check the vacuum pump.

1.CHECK MALFUNCTION CONDITION
  1. Identify when shuddering occurs.
    Result 
    Result
    Proceed to
    When idling
    A
    When engaging engine clutch at vehicle start
    B
    (Clutch system shudders)



B
REPAIR OR REPLACE CLUTCH SYSTEM
A


2.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
  1. Check the wire harness and connector connections of common rail system components.

    OK:
    The wire harnesses and connectors are connected securely.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.READ OUTPUT DTC (RELATING TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output
    A
    Engine related DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


4.TAKE SNAPSHOT DURING IDLING AND 3000 rpm
A176220E02
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.



  1. Take a snapshot of the following Data List items.

    HINT:
    1. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    2. Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
    3. Check the Data List at idling and at 3000 rpm with no load after the engine is warmed up.


    A206040E01


    A206041E01


    Data Condition Idling (Engine Warmed Up) 
    Data List
    Value
    Unit
    Engine Speed
    771
    rpm
    MAP
    94
    kPa
    MAF
    3.87
    g/sec
    Target Common Rail Pressure
    35000
    kPa
    Fuel Press
    33640
    kPa
    Injection Volume
    5.15
    mm3/st
    VN Turbo Command
    57
    %
    Target EGR Position
    54.1
    %
    Actual EGR Valve Pos.
    54.1
    %
    EGR Close Lrn. Val.
    0.52
    V
    EGR Close Lrn. Status
    OK
    -
    Actual Throttle Position
    93
    %
    Throttle Close Learning Val.
    16.9
    deg
    Diesel Throttle Learn Status
    OK
    -
    Accel Position
    0.00
    %
    Injection Feedback Val #1
    0.0
    mm3/st
    Injection Feedback Val #2
    -0.5
    mm3/st
    Injection Feedback Val #3
    0.0
    mm3/st
    Injection Feedback Val #4
    0.1
    mm3/st
    Atmosphere Pressure
    100
    kPa
    Coolant Temp
    76
    °C
    Calculate Load
    14.5
    %
    Pilot 1 Injection Period
    208
    μs
    Pilot 2 Injection Period
    213
    μs

    Data Condition at 3000 rpm (Engine Warmed Up) 
    Data List
    Value
    Unit
    Engine Speed
    3000
    rpm
    Target Booster Pressure
    115.46
    kPa
    MAP
    121
    kPa
    MAF
    52.51
    g/sec
    Target Common Rail Pressure
    67500
    kPa
    Fuel Press
    67460
    kPa
    Target Pump SCV Current
    1039.0
    mA
    Injection Volume
    8.73
    mm3/st
    VN Turbo Command
    62
    %
    Target EGR Position
    42.3
    %
    Actual EGR Valve Pos.
    42.3
    %
    EGR Close Lrn. Val.
    0.52
    V
    EGR Close Lrn. Status
    OK
    -
    Actual Throttle Position
    40
    %
    Throttle Close Learning Val.
    16.9
    deg
    Diesel Throttle Learn Status
    OK
    -
    Accel Position
    14.06
    %
    Injection Feedback Val #1
    0.0
    mm3/st
    Injection Feedback Val #2
    -0.5
    mm3/st
    Injection Feedback Val #3
    0.1
    mm3/st
    Injection Feedback Val #4
    0.0
    mm3/st
    Coolant Temp
    83
    °C
    Calculate Load
    20.7
    %
    Pilot 1 Injection Period
    163
    μs
    Pilot 2 Injection Period
    182
    μs


NEXT


5.CHECK SNAPSHOT (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)


    A176220E02
  1. Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was idling.

    Result 
    Result
    Proceed to
    Fuel Press is within +/-5000 kPa of Target Common Rail Pressure.
    A
    Fuel Press is outside range of +/-5000 kPa from Target Common Rail Pressure.
    B



B
Go to step 19
A


6.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT)


    A176220E02
  1. Check Target Pump SCV Current in the snapshot taken when the engine was idling and at 3000 rpm with no load.

    Result 
    Result
    Proceed to
    Target Pump SCV Current is less than 3000 mA
    A
    Target Pump SCV Current is 3000 mA or higher
    B



B
Go to step 22
A


7.CHECK FUEL INJECTOR COMPENSATION CODE
  1. Read the fuel injector compensation codes .

    OK:
    Compensation codes stored in the ECM match the compensation codes of the installed fuel injectors.



NG
Go to step 37
OK


8.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 to #4)


    A176220E02
  1. Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and has been idling for 1 minute.

    HINT:
    The shift lever should be in neutral and the A/C switch and all accessory switches should be off.


    Result 
    Result
    Proceed to
    Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is 10 mm3/st or less
    A
    Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st
    B*
    Injection Feedback Val #1 to #4 is outside the range of +/-3 mm3/st

    HINT:
    There may be a malfunction in the corresponding cylinder.

    B

    HINT:
    *: When case "B" occurs, usually symptoms may be noticeable, such as difficult starting, rough idling, knocking or black smoke at high common rail pressure.



B
Go to step 32
A


9.CHECK TEMPERATURE WHEN ROUGH IDLING TROUBLE OCCURS
  1. Check the temperature when rough idling trouble occurs.

    Result 
    Result
    Proceed to
    Rough idling only for cold engine.
    A
    Rough idling both for cold and warmed up engine.
    B



B
Go to step 12
A


10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. After engine completely warmed up, allow engine to soak for long time (8 hours or more).

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.

  1. Read the value.

    OK:
    The difference between the displayed value and outside air temperature is below 5°C (9°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


11.INSPECT GLOW PLUG ASSEMBLY
  1. Inspect the glow plug assembly .



NG
REPLACE GLOW PLUG ASSEMBLY (Click here)
OK


12.CHECK EGR VALVE ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Close Lrn. Status.

  1. Read the values.

    Standard:
    EGR Close Lrn. Status is OK

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.

    OK:
    Value smoothly changes to set opening angle.

  1. Remove the EGR valve assembly (Click here).

  1. Visually check the electric EGR control valve for deposits.
    If there are deposits, clean the electric EGR control valve.

    NOTICE:
    1. When cleaning the electric EGR control valve, make sure the valve is completely closed.
    2. Do not forcibly open the valve, as it may be damaged or deformed.
    3. When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.



    A201816E01
  1. Hold the electric EGR control valve up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

    OK:
    No light passes through (there is no gap between the valve and body).

    If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.

    HINT:
    Light passes through part A shown in the illustration even if the valve is completely closed, this is not a problem.



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


13.CHECK DIESEL THROTTLE BODY ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle.

  1. When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.

    OK:
    Value smoothly changes to set opening angle.



NG
REPLACE DIESEL THROTTLE BODY (Click here)
OK


14.RESET ECM
  1. Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.

  1. Reconnect the cable to the negative (-) battery terminal.

  1. Check whether the malfunction has been successfully repaired by performing a driving test.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 15
OK

CHECK FOR INTERMITTENT PROBLEMS 

15.BASIC INSPECTION
  1. Check the fuel quality.

  1. Check the fuel for air.

  1. Check the fuel system for blockages.

  1. Check the air filter.

  1. Check the engine oil.

  1. Check the engine coolant.

  1. Check the engine idling speed and maximum engine speed.

  1. Check the vacuum pump.

    OK:
    Each inspection result is normal.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK


16.CHECK ENGINE MOUNTING INSULATOR
  1. Visually check that the engine mounting insulator is installed correctly and is not crooked or twisted.

    OK:
    No abnormalities.



NG
REPAIR OR REPLACE ENGINE MOUNTING INSULATOR
OK


17.CHECK INTAKE SYSTEM DEPOSIT
  1. Check carbon has accumulated on the intake manifold, cylinder head, etc. and if so, clean it off.


NEXT


18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

HINT:
Symptoms may have appeared due to carbon deposits, etc.


NEXT

END 

19.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


20.CHECK AND REPLACE FUEL INLET LINE
  1. Check the following items, and repair or replace the malfunctioning part if necessary.

    1. Check for fuel filter clogging.

    2. Check for fuel freezing in the fuel line.

    3. Check for clogging or leaks in the fuel pipe and hose between the fuel tank and fuel supply pump.


NEXT


21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


NG
Go to step 24
OK

END 

22.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)


    A204376E02
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) - B32-41 (PCV+)
    Always
    Below 1 Ω
    B46-2 (PCV) - B32-81 (PCV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) or B32-41 (PCV+) - Body ground
    Always
    10 kΩ or higher
    B46-2 (PCV) or B32-81 (PCV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Suction Control Valve)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


23.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
  1. Disconnect the inlet hose from the fuel supply pump.

  1. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

    OK:
    Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

    HINT:
    1. When lack of fuel, fuel pressure drops.
    2. Inspect for fuel filter clogging.
      (Check that the fuel filter is not clogged)



NG
Go to step 39
OK


24.REPLACE FUEL SUPPLY PUMP
  1. Replace the fuel supply pump (Click here).


NEXT


25.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


26.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


27.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Fuel Press.

  1. Check that the fuel pressure of the common rail is within the specification below.

    OK:
    Fuel Press is within +/-5000 kPa of Target Common Rail Pressure when engine is idling and running at 3000 rpm without load.



NG
Go to step 29
OK


28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

29.REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


30.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

32.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

    HINT:
    1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.
    2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.


NEXT


33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

HINT:
Use this Active Test to help determine whether a cylinder has compression loss or not.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

  1. Check the engine speed during the Active Test.

    Result 
    Result
    Proceed to
    The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other.
    B
    Except above
    A

    HINT:
    When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.



B
Go to step 35
A


34.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
  1. Check cylinder compression pressure .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


35.REPLACE INJECTOR OF MALFUNCTIONING CYLINDER
  1. Replace the fuel injector (Click here).


NEXT


36.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


37.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation codes .

  1. Perform the fuel injector pilot quantity learning .


NEXT


38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

39.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP)
  1. Check and replace clogged the fuel pipe.


NEXT


40.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END