TURBOCHARGER > SYSTEM DESCRIPTION |
| OUTLINE OF TURBOCHARGER FAILURE |
State of Turbocharger Failure Repair
It is well known that turbocharger malfunctions cause many symptoms as shown below. However, the mechanisms resulting in these symptoms that indicate turbocharger malfunctions are not well understood. As a result, many unnecessary turbocharger replacements and other repairs are being performed due to lack of knowledge about the turbocharger and turbocharger failure. Therefore, knowing the facts regarding turbocharger malfunctions is useful for making effective repairs and saving time.
Turbocharger Failure Classification
| Symptom | Symptom Description | See page | |
| Noise | Whistling noise | Continuous high frequency noise proportional to engine speed | (Click here) |
| Whining noise | Relatively low frequency noise compared to whistling noise | ||
| Oil leak | External oil leak | Oil leak on surface of turbocharger visible from outside of turbocharger | (Click here) |
| Internal oil leak | Oil leak from inside of bearing housing to inside of either compressor housing or turbine housing through seal ring | ||
| White smoke | Oil smoke | Oil smoke is emitted from exhaust pipe | (Click here) |
| Unburned fuel smoke | Unburned fuel smoke is emitted from exhaust pipe | ||
| Black smoke | Black smoke is emitted from exhaust pipe | (Click here) | |
| Lack of power or hesitation | Vehicle does not reach target speed | (Click here) | |
| Poor acceleration | |||
| Shock during acceleration | |||
| MIL turns on | P0234 | Overboost condition | (Click here) |
| P1251 | Overboost condition (too high) | ||
| P0299 | Underboost | ||
| P0045 | E-VRV failure (not turbocharger failure) | (Click here) | |
| NOISE |
| Probable Cause | Probable Failed Component |
| Turbine shaft imbalance | Turbocharger |
| Leakage from intake line | Intake line |
| Gear noise (Mistaken for turbocharger noise) |
|
Confirm whether the turbocharger is the cause of the noise or not.
![]() |
Disconnect the vacuum hose from the turbocharger actuator.
| *1 | Vacuum Hose |
| *2 | Turbocharger Actuator |
Check whether the noise is reduced or not compared with the noise under the original conditions.
Connect the vacuum hose to the turbocharger actuator.
| Result | Cause of Noise |
| The noise is reduced (or disappears) | Turbocharger |
| The noise does not change | Not turbocharger (other parts) |
| OIL LEAK AND WHITE SMOKE |
| Oil Leak Type | Description | Main Trouble Area |
| Internal oil leak (White smoke) |
|
|
| External oil leak |
|
|

| BLACK SMOKE |
Malfunctions are classified into 2 types as shown below.
| Malfunction | Main Fault |
| Intake air volume shortage | Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being relatively excessive with respect to mass air flow. |
| Excessive injection volume | Excessive injection volume or incorrect injection timing due to fuel system trouble. |
Main Components Related to Black Smoke
| Possible Faulty Component | Main Fault |
| Turbocharger | Abnormally low boost pressure |
| Intake system | Leakage between turbocharger and intake manifold |
| Fuel system |
|
| EGR valve | Stuck or does not close completely |
| Diesel throttle | Stuck or does not move smoothly |
Relation between Turbocharger and Black Smoke
If the boost pressure is lower than normal due to a turbocharger failure, black smoke may occur due to a lack of mass air flow. However, abnormally low boost pressure can be caused by the failure of various components such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormally low boost pressure, but check all the components possibly related to abnormally low boost pressure. Components related to abnormal boost pressure are shown in a chart . For simple and effective troubleshooting, refer to the chart before starting troubleshooting.
| LACK OF POWER AND HESITATION |
Malfunctions are classified into 2 types as shown below.
| Malfunction | Main Fault |
| Intake air volume shortage | Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being restricted. |
| Abnormal injection volume | Abnormal injection volume or timing due to fuel system trouble. |
Main Components Related to Lack of Power and Hesitation
| Possible Faulty Component | Main Fault |
| Turbocharger |
|
| Intake system |
|
| Fuel system |
|
| EGR valve | Stuck or does not close completely |
| Diesel throttle | Stuck or does not move smoothly |
| Exhaust system | Clogging of exhaust line |
Relation between Turbocharger and Abnormal Boost Pressure
If the boost pressure is lower than normal due to a turbocharger failure, lack of power could occur due to an intake air volume shortage. However, abnormal boost pressure can be caused by the failure of various components such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormal boost pressure, but check all the components possibly related to abnormal boost pressure. Components related to abnormal boost pressure are shown in a chart . For simple and effective troubleshooting, refer to the chart before starting troubleshooting.
| MIL TURNS ON |
| BRIEF OUTLINE OF TURBOCHARGER OPERATION AND CONSTRUCTION |
A turbocharger is a component used to supply a larger air volume to the cylinders by recovering exhaust gas energy using a turbine coaxially connected to a compressor.
Principle of Turbocharging
Boost pressure is proportional to turbocharger speed, because the intake air is accelerated by centrifugal force generated by the rotation of the compressor and the increased kinetic energy, i.e. the velocity of the intake air, is converted to pressure energy by the diffuser located around the outlet of the compressor impeller. The compressor is driven by the turbine connected coaxially by the turbine shaft. The turbine is driven by exhaust gas energy. Therefore, when the turbocharger begins boosting the intake air, a larger air volume is supplied to the cylinders and more fuel can be injected. As a result, more exhaust energy will be available and the turbocharger boost increases.

Boost Pressure Control
The amount of energy the turbine can obtain from the exhaust gas is proportional to the expansion ratio, which is defined as the ratio of the turbine inlet exhaust gas pressure to the pressure at the turbine outlet. To control boost pressure, a Variable Nozzle (VN) is used just upstream of the turbine wheel inlet, and controls the expansion ratio. If the VN is closed, the gap between neighboring vanes is narrowed and the turbine inlet exhaust gas pressure, and correspondingly the expansion ratio, increases. Therefore, when the VN is closed, the turbine receives more energy, and the turbine speed and boost pressure increase. On the other hand, if the VN is opened, the turbine inlet exhaust gas pressure decreases, and the turbine speed and boost pressure decrease.
The VN is actuated by a pneumatic actuator. If vacuum pressure is applied to the pneumatic actuator, the actuation rod moves to close the VN and boost pressure increases. If vacuum pressure is removed from the actuator, the VN opens and the boost pressure decreases.

Mechanical Construction of Turbocharger
