Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > Lack of Power or Hesitation

for Preparation Click here


DESCRIPTION


Description 
Malfunction Condition
Main Trouble Area
Related Trouble Area
  1. Lack of power caused by abnormal injection volume (fuel supply pump malfunction or fuel injector malfunction etc.)
  2. Lack of power caused by intake air volume shortage (turbocharger malfunction, front exhaust pipe or exhaust manifold converter blocked)
  1. Fuel injector malfunctions
    1. Fuel injector sliding malfunction
    2. Fuel injector stuck closed
    3. Fuel injector stuck open
    4. Deposits in fuel injector
  2. Abnormal common rail pressure
    1. Fuel supply pump
  3. Abnormal intake air volume
    1. Turbocharger sub-assembly
    2. Front exhaust pipe blockage
    3. Exhaust manifold converter blockage
    4. Diesel throttle does not open
    5. EGR valve does not close
  4. Shift position switch malfunction
  1. Intake air system leakage
  2. Intake air system blockage
  3. Fuel filter element is clogged
  4. Fuel is not supplied to supply pump
  5. Fuel injector compensation code
  6. Mass air flow meter
  7. Manifold absolute pressure sensor
  8. EGR valve
  9. Vehicle modifications
  10. Glow (Poor acceleration when engine is cold)
  11. Low quality fuel
  12. Shift position switch
  13. ECM

HINT:
  1. Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
  2. Check that the vehicle has not been modified in any way prior to the vehicle inspection.
  3. This troubleshooting procedure checks for the cause of a lack of engine power (e.g. the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.


Faults and Symptoms of Common Rail Diesel Components
  1. Engine Control

    Mass Air Flow Meter 
    Component
    Mass air flow meter
    Main fault
    Decrease in performance (foreign matter is stuck)
    Symptoms
    Lack of power, black smoke
    Data List
    MAF

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Intake System 
    Component
    Intake system
    Symptom: Main fault
    1. Lack of power (no black smoke): air filter blockage, air duct is crushed/leaking
    2. Black smoke (no lack of power): Leakage between the turbo and intake manifold
    Data List
    1. MAP (inside intake air pressure)
    2. Target Booster Pressure
      When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

    Turbocharger System 
    Component
    Turbocharger system
    Main fault
    1. Air leak in the turbocharged air passage
    2. Turbocharger (turbine, bearing, variable nozzle)
    Symptoms
    Lack of power (when vehicle starting, when heavy load)
    (Black smoke is not emitted when racing while vehicle stopped)
    Data List
    MAP (inside intake air pressure), Target Booster Pressure
    1. When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.
    2. With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.
    3. Atmospheric pressure decreases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions.

    Exhaust System 
    Component
    Exhaust system
    Main fault
    Blockage
    Symptoms
    Lack of power (high engine speed, when heavy load)
    Data List
    MAP (inside intake air pressure), Target Booster Pressure
    When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

    Glow System 
    Component
    Glow system
    Main fault
    Open circuit, glow plug relay fault
    Symptoms
    Difficult to start, rough idle, knocking, white smoke (when cold)
    Data List
    Check the glow plug indicator light
    Diagnostic Point
    Try to measure the resistance of the glow plug

    Engine - 1 
    Component
    Engine
    Main fault
    Damaged, seized up
    Symptoms
    Cannot crank, crank speed is low, strange noise

    Engine - 2 
    Component
    Engine
    Main fault
    Loss of compression
    Symptoms
    Rough idle (lack of power always)
    Data List
    Engine Speed of Cyl#
    1. When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.
    Injection Feedback Val
    1. If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.

  2. Diesel Injection

    Fuel Supply Pump 
    Component
    Fuel supply pump
    Main fault
    -
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.
    4. If Target Pump SCV Current is 3000 mA or more, the suction control valve may be stuck.

    HINT:
    1. The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.
    2. When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Filter 
    Component
    Fuel filter
    Main fault
    Blockage
    Symptoms
    Difficult to start, engine stalling, rough idle, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure".
    2. If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.
    3. If the fuel pressure is below 25000 kPa then idling will be rough.

    HINT:
    The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.

    Diagnostic Trouble Code
    Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

    Fuel Injector 
    Component
    Fuel injector
    Main fault
    Blockage
    Symptoms
    Rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Injection Feedback Val
    1. When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

    Pressure Discharge Valve 
    Component
    Pressure discharge valve
    Main fault
    Does not completely close
    Symptoms
    Difficult to start, engine stall, rough idle, lack of power

    Injector Driver (EDU) 
    Component
    Injector Driver (EDU)
    Main fault
    Circuit fault: The fuel injector does not open.
    Symptoms
    Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
    Data List
    Same as fuel injector
    Diagnostic Trouble Code
    When the EDU has a fault, some DTCs may be stored.

    Fuel Pressure Sensor 
    Component
    Fuel pressure sensor
    Main fault
    Open circuit, decrease in performance (foreign matter is stuck)
    Symptoms
    Difficult to start, rough idle, engine stall, lack of power
    Data List
    Fuel Press, Target Common Rail Pressure
    1. At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".
    Diagnostic Code
    When the fuel pressure sensor has a fault, some DTCs may be stored.

    Irregular Fuel 
    Component
    Irregular fuel
    Main fault
    -
    Symptoms
    Difficult to start, rough idle (especially when cold)

  3. Diesel EGR

    EGR System 
    Component
    EGR system
    Main fault
    1. Does not move smoothly
    2. Does not close fully
    Symptoms
    1. Rough Idle
    2. EGR valve stuck closed: A loud turbocharger sound.
    3. EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke).
    Data List
    Actual EGR Valve Pos., Target EGR Position
    1. Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%).
    2. Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).
    3. EGR valve is fully closed when the ignition switch is ON (engine stopped).
    4. EGR valve opens to the halfway point at idling after the engine is warmed up.
    5. When the EGR valve does not close, MAF (Mass Air Flow) decreases when the vehicle is accelerated at full throttle. MAP also decreases in comparison to Target Booster Pressure, however there is not a large difference.
    EGR Close Lrn. Val., EGR Close Lrn. Status
    1. In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0.34 to 0.70 V), it is possible that the EGR valve cannot completely close.

  4. Diesel Throttle

    Diesel Throttle System 
    Component
    Diesel throttle system
    Main fault
    Stuck, does not move smoothly
    Symptoms
    1. Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.
    2. Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.
    Data List
    1. Actual Throttle Position (fully closed 100%, fully open 0%)
    2. When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is temporarily closed fully.


Data List Related to Lack of Power

NOTICE:
The Data List values in the table are the results of checking one vehicle after warmed up. Only use these values for reference.

  1. Engine Control

    Engine Speed 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Engine Speed
    Idling: 750 to 850 rpm
    Crankshaft position sensor
    When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.

    MAP 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAP
    MAP (inside intake air pressure)
    1. When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds, a lack of power will be felt.
    2. With the ignition switch ON or vehicle idling, MAP is nearly equal to atmospheric pressure (standard atmospheric pressure = 101 kPa). Atmospheric pressure decreases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions. When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure. The Data List item "Atmosphere Pressure" displays the output of the atmospheric pressure sensor.
    VN Turbo Command
    1. 0%: Fully open vanes (drive rod contracts)
    2. Over 90%: Fully closed vanes (drive rod expands)
    1. Turbocharger fault
    2. Diesel throttle does not open
    3. Intake system blocked
    4. Exhaust system blocked
    1. Inspect while comparing with "Target Booster Pressure".
    2. With the accelerator fully open, if the actual Manifold Absolute Pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.
    3. When value of MAP is low
    Results of real-vehicle check:
    1. Ignition switch ON: 100 kPa
    2. Cranking: 99 kPa
    3. Idling (warm up the engine): 94 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 117 kPa
    5. Running without load (4000 rpm): 138 kPa
    6. Driving with the accelerator fully open at 2000 rpm: 186 kPa
    7. Driving with the accelerator fully open at 3000 rpm: 242 kPa

    MAF 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    MAF
    -
    1. MAF meter
    2. MAF meter circuit
    3. Intake system clogging, leaking
    4. Exhaust system clogging
    5. Turbocharger sub-assembly
    6. Leaking or clogging of turbocharger passages
    7. EGR valve does not close
    1. Based on MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.
    2. If the value is always approximately 0 g/sec.:
      1. Mass air flow meter power source circuit is open.
      2. VG circuit is open or shorted.
      3. EVG circuit is open.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 g/sec.
    2. Cranking: 5.07 g/sec.
    3. Idling (warm up the engine): 3.87 g/sec. (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 34 g/sec.
    5. Driving with the accelerator fully open at 2000 rpm: 79 g/sec.
    6. Driving with the accelerator fully open at 3000 rpm: 138 g/sec.

    HINT:
    The maximum fuel injection volume is controlled according to the output from the mass air flow meter.


    Intake Air 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Intake Air
    After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    Intake air temperature sensor
    If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

    Coolant Temp 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Coolant Temp
    1. Engine coolant temperature is approximately equal to intake air temperature after leaving overnight. After warm-up: Engine coolant temperature is 70°C (158°F) or higher.
    2. In cases when the engine coolant temperature sensor output is obviously higher than the actual engine coolant temperature, when it is cold, there will be difficulty starting due to problems with glow plugs or insufficient fuel injection.
    3. In cases when the engine coolant temperature sensor output is obviously lower than the actual engine coolant temperature, when it is warm, there will be difficulty starting (black smoke will also occur) due to an excess of injected fuel.
    Engine coolant temperature sensor
    If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

  2. Diesel Injection

    Target Common Rail Pressure 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Common Rail Pressure
    -
    -
    1. Inspect the (actual) fuel pressure, comparing it against the common rail target value.
    2. Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions.
    Results of real-vehicle check:
    1. Ignition switch ON: 35000 kPa
    2. Cranking: 50000 kPa
    3. Idling (warm up the engine): 35000 kPa (2 minutes after starting the vehicle)
    4. Running without load (2500 rpm): 63240 kPa
    5. Running without load (3500 rpm): 72950 kPa
    6. Driving with the accelerator fully open at 2000 rpm: 138590 kPa
    7. Driving with the accelerator fully open at 3000 rpm: 183210 kPa

    Fuel Press 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Fuel Press
    1. In a stable operating condition (e.g. idling), Fuel Press is Target Common Rail Pressure +/-5000 kPa.
    2. When the Fuel Press is 20000 kPa below Target Common Rail Pressure, a lack of power will be felt.
    3. When Fuel Press is below 25000 kPa, rough idling will occur.
    1. If there is fuel supply pump (lack of discharge quantity) or pressure discharge valve (will not fully close) breakdown, the fuel pressure will drop. Also, a blocked fuel filter, leakage from fuel pipes, and an empty fuel tank will also make the fuel pressure drop.
    2. When there is a fault with the fuel supply pump, there is a possibility of lack of power, starting trouble, engine stall, rough idle, etc.
    1. Fuel Press is the actual common rail fuel pressure.
    2. Inspect by comparing the fuel pressure with Target Fuel Pressure.
    3. The ECM uses Fuel Press for feedback control of Target Fuel Pressure via the supply pump.
      The injection amount is determined based on the injection timing and fuel pressure.
      Also, the spray pattern is selected based on the fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 0 kPa
    2. Cranking: 35390 kPa
    3. Idling (warm up the engine): 33640 kPa
    4. Running without load (2500 rpm): 62920 kPa
    5. Driving with the accelerator fully open at 2000 rpm: 134390 kPa
    6. Driving with the accelerator fully open at 3000 rpm: 178670 kPa

    Target Pump SCV Current 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target Pump SCV Current
    1. Idling after warming up: around 923 to 1123 mA. When this value is large, the fuel supply pump is trying to increase the fuel discharge rate.
    2. If the value becomes 3000 mA or higher, the suction control valve may become stuck.
    With this data, component fault not specified, use this data as a reference
    1. ECU-calculated value for the suction control valve actuation target current.
    1. Value is large when a high fuel pressure is desired.
    2. When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.
    Results of real-vehicle check:
    1. Ignition switch ON: 1008 mA
    2. Cranking: 1155 mA
    3. Running without load (2500 rpm): 1300 mA
    4. Driving with the accelerator fully open at 2000 rpm: 1233 mA
    5. Driving with the accelerator fully open at 3000 rpm: 1397 mA

    Injection Feedback Val #1 (to #4) 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Feedback Val #1 (to #4)
    Injection Feedback Val:
    1. When idling after the engine is warmed up, to make each cylinder engine speed equal, the fuel quantity of each fuel injector is corrected.
    2. Cylinders more than 3 mm3/st may have a fault.

    HINT:
    Read the value after one minute of idling after warm up (engine coolant temperature above 70°C (158°F)). This value is only calculated when idling.

    1. "Breakdown of injector or lack of compression" of a cylinder with an irregular Injection Feedback Val # value.
    2. Do a compression Active Test. If there is a cylinder that is around 100 rpm more than the other cylinders, there is a possibility that that cylinder has a fault.
    3. If all the cylinder speeds are even according to the compression Active Test result, consider the injector of the cylinder that has a fault.
    4. With fuel injector faults, there is a possibility of rough idling, lack of power, difficulty starting, black smoke, white smoke and knocking.
    With Injection Feedback Val, find the malfunctioning cylinders. However, before replacing the injector, identify the malfunctioning cylinders with a power balance test.

    Injection Volume 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Injection Volume
    1. Diagnose the fuel injector faults from Injection Feedback Val # and Injection Volume at idling.
    2. When Injection Volume is more than 10 mm3/st at idle with the engine warmed up and Injection Feedback Val # of all cylinders is less than 2.0 mm3/st, the following malfunctions are possible:
      - All cylinder fuel injectors are slightly blocked.
      - Fuel filter is blocked.
      - Poor quality fuel, increase in engine friction.
    All cylinders
    -
    Results of real-vehicle check:
    1. Cranking: 22 mm3/st
    2. Idling (warm up the engine): 5 mm3/st
    3. Running without load (2500 rpm): 8 mm3/st
    4. Running without load (4700 rpm): 16 mm3/st
    5. Driving with the accelerator fully open at 2000 rpm: 75 mm3/st
    6. Driving with the accelerator fully open at 3000 rpm: 78 mm3/st

  3. Diesel Throttle

    Actual Throttle Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual Throttle Position
    1. When the ignition switch is turned to ON (engine stopped), the diesel throttle is fully open, when the ignition switch is turned from ON to off, it will be fully closed temporarily.
    2. During idling, the throttle is open partway.
    3. When stuck closed (almost fully closed), there is a possibility of lack of power, rough idling, engine stall and black smoke.
    Throttle valve
    Actual Throttle Position is the closing percentage of the throttle valve.
    1. Fully closed: 100%
    2. Fully open: 0%

      HINT:
      There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).

    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 93%
    4. Running without load (2500 rpm): 51%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

  4. Diesel EGR

    Target EGR Position 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Target EGR Position
    -
    -
    1. Fully open: 100%
    2. Fully closed: 0%
    3. Used for comparison to "Actual EGR Valve Pos".
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%

    Actual EGR Valve Pos. 
    Data List
    Judgment of Data List Values
    Faulty Component
    Diagnosis Note
    Actual EGR Valve Pos.
    Generally Actual EGR Valve Pos. = Target EGR Position +/-5% (completely closed = 0%, completely open = 100%).
    The EGR valve Active Test can be used to check whether Actual EGR Valve Pos. = Target EGR Position (take into consideration the temperature of the intake air and the coolant temperature when the malfunction occurs).
    Sometimes the malfunction only occurs around a certain temperature. Take into consideration the temperature of the intake air and the coolant temperature when the malfunction occurs.
    EGR valve
    Inspect while comparing to "Target EGR Position".
    Results of real-vehicle check:
    1. Ignition switch ON: 0%
    2. Cranking: 0%
    3. Idling (warm up the engine): 54%
    4. Running without load (2500 rpm): 47%
    5. Driving with the accelerator fully open at 2000 rpm: 0%
    6. Driving with the accelerator fully open at 3000 rpm: 0%


Examples of Actual Malfunctions

HINT:
  1. The purpose of the following examples is to help you to understand the relationship between each Data List item when a certain malfunction occurs. Understanding this relationship helps you to find the real root cause easier.
  2. The following are examples of actual malfunctions of a common rail diesel engine.
  3. Use them for reference when diagnosing malfunctions.
  4. These are not data of the RAV4 2AD-FHV.



  1. Lack of power caused by overly low boost pressure


    A183890E03



  2. Lack of power caused by overly low MAF


    A190056E01

    In this example, the MAF (Mass Air Flow) value decreases greatly due to foreign matter being stuck to the MAF sensor and causes a lack of power. The maximum fuel injection volume value is limited by the MAF value. As a result, there is a lack of power due to a lack of injection volume.
    In this case, even when the accelerator is fully open, the calculated load is low (Calculated Load = Injection Volume / Maximum Injection Volume at Current Engine Speed).
    Basically, the Manifold Absolute Pressure (MAP) is approximately equal to the Target Booster Pressure and this indicates that the turbocharger functions properly.



  3. EGR valve stuck in open position


    A190058E01

    In this example, the EGR valve is stuck in the open position. Even with the accelerator pedal fully depressed, the EGR does not fully close and the MAF signal is low.
    Therefore, the fuel injection volume becomes limited and there is a lack of power. Jerking is also evident. At this time, even while accelerating with the accelerator fully open, the calculated load is low (Calculated Load = Current Injection Volume / Maximum Injection Volume at Current Engine Speed).
    Basically, the Manifold Absolute Pressure (MAP) is approximately equal to Target Booster Pressure and this indicates that the turbocharger functions properly.


INSPECTION PROCEDURE


Explanation of Symptom

Lack of Power
The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air.
The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector is open for. Basically, the fuel pressure is controlled to reach the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure.
The manifold absolute pressure is controlled to reach the Target Booster Pressure. Also, when accelerating the vehicle at full throttle, the throttle is fully open and the EGR valve is fully closed, preserving the mass air flow.

Trouble Area Chart According to Problem Cause

A216502E01


A215690E02

NOTICE:
  1. After replacing the fuel supply pump, the ECM needs initialization (Click here).
  2. After replacing a fuel injector, the ECM needs registration (Click here).

HINT:
  1. Before troubleshooting, conduct the following:
    1. Check the fuel quality.
    2. Check the fuel for air.
    3. Check the fuel system for blockages.
    4. Check the air filter.
    5. Check the engine oil.
    6. Check the engine coolant.
    7. Check the engine idling speed and maximum engine speed.

1.READ OUTPUT DTC (RELATED TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output
    A
    Engine related DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.TAKE SNAPSHOT DURING DRIVING TEST
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.



    A176220E04

    A206042E01


    A206043E01


    A206044E01


    A206050E01

  1. Take a snapshot of the following Data List items with the intelligent tester.

    HINT:
    1. Driving pattern for the test should be decided based on customer's comment regarding the situation in which the problem occurred.
    2. A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
    3. Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.
    4. Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator fully open (obey all laws and regulations, and pay attention to driving conditions while driving the vehicle). Then, check the Data List with the engine warmed up and idling (the shift lever in neutral and A/C switch and all accessory switches off).


    Reference Values with Engine Speed at 3500 rpm (Point A) 
    Data List
    Value
    Unit
    Vehicle Speed
    44
    km/h
    Engine Speed
    3500
    rpm
    Accel Position
    99.60
    %
    Target Booster Pressure
    234.19
    kPa
    MAP
    227
    kPa
    MAF
    140.96
    g/sec.
    Calculate Load
    100
    %
    Target Common Rail Pressure
    194350
    kPa
    Fuel Press
    189820
    kPa
    Target Pump SCV Current
    1402.8
    mA
    Injection Volume
    70.52
    mm3/st
    VN Turbo Command
    44
    %
    Actual EGR Valve Pos.
    0
    %
    Actual Throttle Position
    0
    %
    AF Lambda B1S1
    1.167
    -
    AFS Voltage B1S1
    0.27
    V


Data Condition Idling (Engine warmed up) 
Data List
Value
Unit
Engine Speed
771
rpm
Target Booster Pressure
92.69
kPa
MAP
94
kPa
MAF
3.87
g/sec.
Target Common Rail Pressure
35000
kPa
Fuel Press
33640
kPa
Injection Volume
5.15
mm3/st
VN Turbo Command
57
%
Actual EGR Valve Pos.
54.1
%
Target EGR Position
54.1
%
Actual Throttle Position
93
%
Accel Position
0.00
%
Injection Feedback Val #1
0.0
mm3/st
Injection Feedback Val #2
-0.5
mm3/st
Injection Feedback Val #3
0.0
mm3/st
Injection Feedback Val #4
0.1
mm3/st
Atmosphere Pressure
100
kPa
Coolant Temp
76
°C

HINT:
  1. Examples of Actual Malfunctions (See "Diagnostic Help" menu)
    1. Lack of power caused by overly low boost pressure
    2. Lack of power caused by overly low MAF
    3. EGR valve stuck in open position
  2. For engine protection, or exhaust gas or fuel economy related reasons, there are some ranges of engine operation where engine power feels like it flattens out, but this is not a malfunction.

  1. Check for a lack of power during the driving test.

    Result 
    Result
    Proceed to
    Apparent lack of power is present
    A
    Apparent lack of power is not present
    B



B
Go to step 50
A


3.CHECK SNAPSHOT


    A176220E02
  1. Check the condition of the vehicle using the snapshot taken during the lack of power.

    Result 
    Result
    Proceed to
    Fuel Press is less than "Target Common Rail Pressure - 20000 kPa" when accelerating with accelerator fully open
    B
    Target Pump SCV Current 3000 mA or more
    C
    One of the Injection Feedback Val #1 to 4 values is outside the range of +/-3 mm3/st when idling after warm up
    D
    Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st when idling after warm up
    E
    None of the above conditions apply
    A



B
Go to step 14

C
Go to step 17

D
Go to step 30

E
Go to step 40
A


4.CHECK SNAPSHOT


    A176220E02
  1. Check the condition of the vehicle using the snapshot taken during the lack of power.

    Result 
    Result
    Proceed to
    MAP is less than "Target Booster Pressure - 20 kPa" (MAF is normal) when accelerating with accelerator fully open
    A
    MAF is low when accelerating with accelerator fully open (MAP is normal)
    1. 3000 rpm: 105 g/sec. or less
    2. 3500 rpm: 125 g/sec. or less
    3. 4000 rpm: 135 g/sec. or less

    HINT:
    If MAF (Mass Air Flow) decreases, Calculate Load will be 80% or less when accelerating with the accelerator fully open.

    B
    MAP and MAF are both low when accelerating with the accelerator fully open
    C
    None of the above conditions apply
    D

    HINT:
    When racing the engine, if the boost pressure becomes less than atmospheric pressure, there may be blockage in the intake system, or the turbocharger shaft may be stuck.



B
Go to step 7

C
Go to step 9

D
Go to step 23
A


5.INSPECT VACUUM HOSE
  1. Check the vacuum hose connection (manifold absolute pressure sensor).

    OK:
    Vacuum hose is connected securely.



NG
REPLACE VACUUM HOSE
OK


6.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERE PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

  1. Compare MAP to Atmosphere Pressure when the ignition switch is ON (engine stopped).

    HINT:
    1. If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
    2. Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).


Result 
Result
Proceed to
Atmosphere Pressure is different from actual atmospheric pressure
A
MAP is different from actual atmospheric pressure
B
MAP and Atmosphere Pressure have the same value
C


B
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

C
Go to step 9
A

REPLACE ECM (Click here)  

7.CHECK MASS AIR FLOW METER
  1. Check the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


8.CHECK EGR VALVE ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Close Lrn. Status.

  1. Read the values.

    Standard:
    EGR Close Lrn. Status is OK

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.

    OK:
    Value smoothly changes to set opening angle.

  1. Remove the EGR valve assembly (Click here).

  1. Visually check the electric EGR control valve for deposits.
    If there are deposits, clean the electric EGR control valve.

    NOTICE:
    1. When cleaning the electric EGR control valve, make sure the valve is completely closed.
    2. Do not forcibly open the valve, as it may be damaged or deformed.
    3. When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.



    A201816E01
  1. Hold the electric EGR control valve up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

    OK:
    No light passes through (there is no gap between the valve and body).

    If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.

    HINT:
    Light passes through part A shown in the illustration even if the valve is completely closed. This is not a problem.



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


9.READ VALUE USING INTELLIGENT TESTER (ACCEL POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.

  1. Read the value.

    Standard Value:

    Condition
    Standard Value
    Accelerator pedal released
    0%
    Accelerator pedal depressed
    95% or more
    Accelerator pedal released → depressed

    HINT:
    Make sure the Accel Position opening angle changes smoothly.

    0 to 95% or more



NG
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
OK


10.CHECK DIESEL THROTTLE BODY ASSEMBLY
  1. Check the diesel throttle body assembly (Click here).



NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY (Click here)
OK


11.CHECK INTAKE SYSTEM
  1. Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

    HINT:
    1. Check that the intercooler is not clogged with foreign matter.
    2. Check that there are no disconnected, pinched or leaking hoses or pipes.
    3. Check that there are no modifications made by the user.

    OK:
    No leakage or blockage.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK


12.INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Inspect the turbocharger sub-assembly .



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check whether the lack of power has been successfully repaired.

    OK:
    Malfunction has been repaired successfully.

    HINT:
    Symptoms may have appeared due to carbon deposits, etc.



NG
Go to step 38
OK

END 

14.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.



    A176220E02
  1. Take a snapshot with the intelligent tester during the Active Test.

    HINT:
    Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.



  1. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

    HINT:
    In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


    A190323E06

    OK:
    The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.

    HINT:
    1. "Target Common Rail Pressure" means target fuel pressure controlled by the ECM.
    2. "Fuel Press" means actual fuel pressure.
    3. When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.
    4. If the pressure discharge valve mounted on the common rail is malfunctioning, the actual fuel pressure will change as indicated by "Pressure Discharge Valve Malfunctioning" in the illustration.


    Result 
    Result
    Proceed to
    Difference between target fuel pressure and actual fuel pressure is less than 10000 kPa
    A
    Difference between target fuel pressure and actual fuel pressure is 10000 kPa or more
    B



B
Go to step 16
A

END 

16.INSPECT COMMON RAIL ASSEMBLY
  1. Inspect the common rail assembly .



OK
Go to step 18

NG
Go to step 47

17.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)


    A204376E02
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) - B32-41 (PCV+)
    Always
    Below 1 Ω
    B46-2 (PCV) - B32-81 (PCV-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B46-1 (+B) or B32-41 (PCV+) - Body ground
    Always
    10 kΩ or higher
    B46-2 (PCV) or B32-81 (PCV-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Suction Control Valve)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
  1. Disconnect the inlet hose from the fuel supply pump.

  1. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

    OK:
    Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

    HINT:
    1. When lack of fuel, fuel pressure drops.
    2. Inspect for fuel filter clogging.
      (Check that the fuel filter is not clogged)



NG
Go to step 44
OK


19.REPLACE FUEL SUPPLY PUMP
  1. Replace the fuel supply pump (Click here).


NEXT


20.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


21.PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).


NEXT


22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check whether the lack of power has been successfully repaired.

    HINT:
    Fuel Press is within +/-5000 kPa of Target Common Rail Pressure.


NEXT

END 

23.READ VALUE USING INTELLIGENT TESTER (CATALYST DIFFERENTIAL PRESS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press.

  1. Check the differential pressure at an engine speed of 3000 rpm with no load.

    Standard:
    Catalyst Differential Press is less than 0.25

  1. With the vehicle stopped, fully depress the accelerator pedal for 5 seconds and then release it.*A

  1. Repeat procedure *A 10 times.*B

  1. Check for black smoke emission during the above procedures *A and *B.

    Standard:
    Black smoke is emitted less than 5 times.

    HINT:
    Even if the black smoke is very thin, count the black smoke emission if there is any visible smoke.


    Result 
    Differential Pressure (kPa)
    Proceed to
    Note
    Catalyst Differential Press 0.25 or more
    at 3000 rpm (No engine load)
    B
    An extremely large amount of PM (Particulate Matter) has accumulated in the DPNR catalyst.
    Black smoke is emitted 5 times or more
    B
    The DPNR catalyst cannot trap PM because it is melted or cracked, and therefore must be replaced.
    Also, if a piece of the catalyst breaks off, due to melting or another condition, and enters the exhaust pipe downstream, the exhaust pipe could be blocked, possibly causing a different malfunction.
    Therefore, when replacing the DPNR catalyst, visually inspect the rear surface of the DPNR filter substrate to determine if replacement of the exhaust pipe is necessary.
    Except above
    A
    -

    HINT:
    1. If the "Catalyst Differential Press" is more than about 0.4, DTC P2002 (Particulate Trap Efficiency Below Threshold [Bank 1]) will be stored.
    2. The standard for the differential pressure sensor output is as follows:
      Reference 
      Condition
      Differential Pressure Output
      Ignition switch ON
      Approximately 0 kPa
    3. If the Differential Pressure output is always 3 kPa, an open or short may exist in the differential pressure sensor circuit.
    4. If the Differential Pressure outputs a negative value when the engine is maintained at an engine speed of 3000 rpm with no load, the hose and pipe connections may be incorrect.



B
REPLACE MONOLITHIC CONVERTER ASSEMBLY (Click here)
A


24.CHECK TEMPERATURE WHEN LACK OF POWER OCCURS
  1. Check the temperature when the lack of power occurs.

    Result 
    Result
    Proceed to
    Poor acceleration only when engine is cold
    A
    Poor acceleration when engine is cold and warm
    B



B
Go to step 27
A


25.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    After warming up the engine, the engine coolant temperature should be 70°C (158°F) or more. After leaving the vehicle overnight, the engine coolant temperature should be nearly equal to the intake air temperature.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


26.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
  1. Inspect the glow plug assembly .



NG
REPLACE GLOW PLUG ASSEMBLY (Click here)
OK


27.INSPECT INJECTOR COMPENSATION CODE
  1. Read the injector compensation codes .

    OK:
    Compensation codes stored in the ECM match the compensation codes of the installed fuel injectors.



NG
Go to step 42
OK


28.CHECK FUEL QUALITY
  1. Check that fuel with a low cetane number is used.


NEXT


29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check whether the lack of power has been successfully repaired by starting the engine.


NEXT

END 

30.INSPECT INJECTOR COMPENSATION CODE
  1. Read the injector compensation codes .

    OK:
    Compensation codes stored in the ECM match the compensation codes of the installed fuel injectors.



NG
Go to step 42
OK


31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)

HINT:
Use this Active Test to determine the malfunctioning cylinder.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

    HINT:
    1. If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.
    2. If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.


NEXT


32.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

HINT:
Use this Active Test to help determine whether a cylinder has compression loss or not.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

  1. Check the engine speed during the Active Test.

    OK:
    The values of Engine Speed of Cyl #1 to #4 are within 10 rpm of each other.

    HINT:
    When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a loss of compression in that cylinder.



OK
Go to step 34

NG
Go to step 33

33.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

HINT:
Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.

  1. Check the cylinder compression pressure .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


34.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

HINT:
The injector is determined to be faulty as the corresponding cylinder is malfunctioning, but has no compression loss.

  1. Replace the fuel injector of the malfunctioning cylinder (Click here).


NEXT


35.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


36.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation code .

  1. Perform the fuel injector pilot quantity learning .


NEXT


37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

38.CHECK INTAKE SYSTEM DEPOSIT
  1. Check carbon is accumulating on the intake manifold, cylinder head, etc. and if so, clean it off.


NEXT


39.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

HINT:
Symptoms may have appeared due to carbon deposits, etc.


NEXT

END 

40.REPLACE FUEL INJECTORS OF ALL CYLINDERS
  1. Replace the fuel injectors (Click here).


NEXT


41.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


42.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation codes .

  1. Perform registration of the fuel injector pilot quantity learning values .


NEXT


43.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

44.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP)
  1. Check and replace clogged the fuel pipe.


NEXT


45.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


46.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

47.REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


48.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .


NEXT


49.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END 

50.COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE
  1. Confirm the situation in which the the lack of power was experienced by the customer again, and compare the driving feeling and collect data with the intelligent tester under the same conditions using a similar vehicle with the same engine.

    HINT:
    Confirm the state of the following conditions when the lack of power was experienced.
    1. Accelerator pedal position (vehicle load)
    2. Vehicle speed
    3. Engine coolant temperature
    4. Atmospheric temperature
    5. Driving conditions before the lack of power occurred
    6. Climate
    7. Road and traffic conditions
    8. When (what day) the problem was noticed
    9. Whether the problem occurs suddenly or gradually
    10. How often the problem occurs
    11. Why did the customer feel there is a lack of power (e.g. the customer compared their vehicle with another vehicle, somebody told the customer that their vehicle has a lack of power).
    12. Level of lack of power (slight or drastic)


    Result 
    Result
    Proceed to
    Significant difference is found
    A
    Significant difference is not found
    B



A
Go to step 3
B


51.EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER
  1. Vehicle performance is normal.
    The problem seems to be that the customer believes the vehicle is lacking power.
    The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.


NEXT

END