DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 | Conditions (a) and (b) continue for 10 seconds or more (2 trip detection logic): (a) The air fuel ratio sensor voltage is higher than 3.8 V. (b) The heated oxygen sensor voltage is 0.15 V or higher. |
|
| While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 3.6 mA or higher for 3 seconds (2 trip detection logic). |
| |
| P2196 | Conditions (a) and (b) continue for 10 seconds or more (2 trip detection logic): (a) The air fuel ratio sensor voltage is below 2.8 V for 10 seconds. (b) The heated oxygen sensor voltage is below 0.6 V. |
|
| While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is below 1.0 mA for 3 seconds (2 trip detection logic). |
|



| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1 S1 (A/F) | +25% | Rich | Below 3.1 |
| -12.5% | Lean | Higher than 3.4 | |
| O2S B1 S2 (HO2) | +25% | Rich | Higher than 0.55 |
| -12.5% | Lean | Below 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P2195 or P2196 is output | A |
| DTC P2195 or P2196 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | ||
| ||
| 3.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / Monitor Status.
Check that the status of "O2 Sensor" is "Complete".
If the status is still "Incomplete", drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1 S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut (refer to Monitor Driving Pattern 2 [Detail for "C" through "F"] in Confirmation Driving Pattern).
| Test Value | Proceed to |
| Within normal range (1.0 mA or higher, and below 3.6 mA) | A |
| Outside normal range (below 1.0 mA, or 3.6 mA or higher) | B |
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1 S1 and Engine Speed / Function / Snap Shot Record.
Check the air fuel ratio sensor voltage 3 times, once under each of the following conditions:
While idling (for at least 30 seconds) (Step "A").
At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed) (Step "B").
Engine speed raised to 4000 rpm and then accelerator pedal quickly release so that the throttle valve is fully closed (Step "C").
| Condition | A/F Sensor Voltage Variation | Reference |
| Step "A" and Step "B" | Remains at approximately 3.3 V | Between 3.1 V and 3.4 V |
| Step "C" | Increases to 3.8 V or higher | Occurs during engine deceleration (when fuel-cut performed) |

|
| ||||
| OK | |
| 5.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P2195 or P2196 is output | B |
|
| ||||
| A | ||
| ||
| 8.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HA1A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA1A) - 4 (A1A-) | Always | 10 kΩ or higher |
| *1 | Component without harness connected (Air Fuel Ratio Sensor) |
Reconnect the air fuel ratio sensor.
|
| ||||
| OK | |
| 9.CHECK AIR FUEL RATIO SENSOR (POWER SOURCE) |
![]() |
Disconnect the air fuel ratio sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B113-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
Reconnect the air fuel ratio sensor connector.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
![]() |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B113-1 (HA1A) - B32-104 (HA1A) | Always | Below 1 Ω |
| B113-3 (A1A+) - B32-103 (A1A+) | Always | Below 1 Ω |
| B113-4 (A1A-) - B32-126 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B113-1 (HA1A) or B32-104 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B113-3 (A1A+) or B32-103 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B113-4 (A1A-) or B32-126 (A1A-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
Reconnect the air fuel ratio sensor connector.

|
| ||||
| OK | |
| 11.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage (Click here).
|
| ||||
| OK | |
| 12.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 13.INSPECT INJECTOR ASSEMBLY |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P2195 or P2196 is output | B |
|
| ||||
| A | ||
| ||
| 17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY) |
![]() |
Disconnect the air fuel ratio sensor connector.
Remove the integration relay (A/F relay) from the engine room No. 1 relay block.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B113-2 (+B) - 1A-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B113-2 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
| *2 | Front view of wire harness connector (to Integration Relay) |
| *3 | Engine Room No. 1 Relay Block |
Reconnect the air fuel ratio sensor connector.
Reconnect the integration relay connector.
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||
| 18.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||