Home › ENGINE · 1AZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.


A079413E25


DTC No.
DTC Detection Condition
Trouble Area
P0500
While vehicle being driven, no vehicle speed sensor signal to ECM.
(1 trip detection logic: Automatic transaxle)
(2 trip detection logic: Manual transaxle)
  1. Open or short in speed signal circuit
  2. Combination meter
  3. Skid control ECU
  4. ECM
  5. Vehicle speed sensor

WIRING DIAGRAM


A238382E05


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in speedometer malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    E22-39 (+S) - A12-8 (SPD)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    E22-39 (+S) or A12-8 (SPD) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the wire has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. the navigation system, audio system, etc.).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FOR OTHER SYSTEMS RELATED TO SPEED SIGNAL)
OK


4.CHECK COMBINATION METER (+S VOLTAGE)


    A127854E39
  1. Disconnect the combination meter connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-39 (+S) - Body ground
    Ignition switch on (IG)
    4.5 to 5.5 V

Text in Illustration 
*a
Front view of wire harness connector
(to Combination Meter)


NG
REPLACE ECM (Click here)
OK


5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM)


    A127943E65
  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E22-39 (+S) - Body ground
    1. Ignition switch on (IG)
    2. Wheel turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 6
OK

REPLACE ECM (Click here)  

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)


    A127943E66
  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E22-38 (SI) - Body ground
    1. Ignition switch on (IG)
    2. Wheel turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 7
OK

REPLACE COMBINATION METER (Click here)  

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
  1. Disconnect the combination meter connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    w/ VSC 
    Tester Connection
    Condition
    Specified Condition
    E22-38 (SI) - A67-11 (SP1)
    Always
    Below 1 Ω
    w/o VSC 
    Tester Connection
    Condition
    Specified Condition
    E22-38 (SI) - A27-26 (SP1)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    w/ VSC 
    Tester Connection
    Condition
    Specified Condition
    E22-38 (SI) or A67-11 (SP1) - Body ground
    Always
    10 kΩ or higher
    w/o VSC 
    Tester Connection
    Condition
    Specified Condition
    E22-38 (SI) or A27-26 (SP1) - Body ground
    Always
    10 kΩ or higher

Result 
Result
Proceed to
NG
A
OK (w/ VSC)
B
OK (w/o VSC)
C


B
REPLACE SKID CONTROL ECU (Click here)

C
REPLACE SKID CONTROL ECU (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR