DTC C1407 Open or Short in Rear Speed Sensor RH Circuit |
DTC C1408 Open or Short in Rear Speed Sensor LH Circuit |

| DTC Code | DTC Detection Condition | Trouble Area |
| C1407 C1408 | Either of the following is detected:
|
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Speed Open | RR speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| RL Speed Open | RL speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| Result | Proceed to | |
| There are no momentary interruptions. | A | |
| There are momentary interruptions. | 2WD | B |
| 4WD | C | |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) | Actual wheel speed | Similar to speed indicated on the speedometer. |
| RL Wheel Speed | RL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) | Actual wheel speed | Similar to speed indicated on the speedometer. |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
| Result | Proceed to | |
| OK | A | |
| NG | 2WD | B |
| 4WD | C | |
|
| ||||
|
| ||||
| A | |
| 3.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs (C1407 and C1408) are not output. | A |
| DTCs (C1407 and/or C1408) are output. | B |
|
| ||||
| A | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1 ("A"-2) - W1 ("B"-1) | Always | Below 1 Ω |
| W1 ("A"-2) - W1 ("B"-2) | Always | 10 kΩ or higher |
| W1 ("A"-2) - Body ground | Always | 10 kΩ or higher |
| W1 ("A"-1) - W1 ("B"-2) | Always | Below 1 Ω |
| W1 ("A"-1) - W1 ("B"-1) | Always | 10 kΩ or higher |
| W1 ("A"-1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| X1 ("A"-2) - X1 ("B"-1) | Always | Below 1 Ω |
| X1 ("A"-2) - X1 ("B"-2) | Always | 10 kΩ or higher |
| X1 ("A"-2) - Body ground | Always | 10 kΩ or higher |
| X1 ("A"-1) - X1 ("B"-2) | Always | Below 1 Ω |
| X1 ("A"-1) - X1 ("B"-1) | Always | 10 kΩ or higher |
| X1 ("A"-1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
![]() |
Turn the ignition switch off.
for 2WD:
Reconnect the skid control sensor wire.
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the skid control ECU connector and the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A67-17 (RR+) - W1-2 | Always | Below 1 Ω |
| A67-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A67-16 (RR-) - W1-1 | Always | Below 1 Ω |
| A67-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A67-17 (RR+) - K29-1 | Always | Below 1 Ω |
| A67-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A67-16 (RR-) - K29-2 | Always | Below 1 Ω |
| A67-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A67-5 (RL+) - X1-2 | Always | Below 1 Ω |
| A67-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A67-4 (RL-) - X1-1 | Always | Below 1 Ω |
| A67-4 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A67-5 (RL+) - K28-1 | Always | Below 1 Ω |
| A67-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A67-4 (RL-) - K28-2 | Always | Below 1 Ω |
| A67-4 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT SKID CONTROL ECU (SENSOR INPUT) |
![]() |
Reconnect the skid control ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| W1-2 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| K29-1 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| X1-2 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| K28-1 - Body ground | Ignition switch ON | 8 to 14 V |
| Result | Proceed to | |
| OK | for 2WD | A |
| for 4WD | B | |
| NG | C | |
|
| ||||
|
| ||||
| A | ||
| ||