Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for AWD)
RM30B0U _52 Drivetrain _009984 DRIVE SHAFT / PROPELLER SHAFT _0054769 FRONT DRIVE SHAFT ASSEMBLY(for AWD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for AWD)  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 3.REMOVE REAR ENGINE UNDER COVER LH

Hide 4.REMOVE REAR ENGINE UNDER COVER RH

Hide 7.REMOVE FRONT AXLE SHAFT NUT LH

Hide 8.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 9.DISCONNECT FRONT SPEED SENSOR LH

Hide 10.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 11.REMOVE FRONT STABILIZER LINK ASSEMBLY LH

Hide 12.REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 13.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 14.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 15.DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH

a.
C264664

Remove the bolt and detach the 2 guides.


b.
C129488
1.708,1.052 2.625,1.052 2.625,1.052 2.625,0.833 true 1.625,0.833 2.875,0.833 true 2.979,0.729 3.292,0.927 0.313,0.198 10 *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and front axle hub sub-assembly.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Using a plastic-faced hammer, disconnect the front drive shaft assembly from the steering knuckle with axle hub.

NOTICE:
·

Be careful not to damage the boot and drive shaft dust cover.

·

Do not excessively push out the drive shaft from the front axle hub.




Hide 16.DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:

Use the same procedure described for the LH side.


Hide 17.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C264655
1.833,0.833 1.75,1.917 1.75,1.917 2.417,1.167 true 1.75,1.917 1.5,1.917 false 1.208,1.833 1.667,2.031 0.458,0.198 10 SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Be careful not to damage the transaxle oil seal, inboard joint boot and drive shaft dust cover.

·

Be careful not to drop the front drive shaft assembly LH.




Hide 18.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.
C239399

Disconnect the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.


b.

Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

NOTICE:
·

Be careful not to damage the transaxle oil seal, inboard joint boot and drive shaft dust cover.

·

Be careful not to drop the front drive shaft assembly RH.




c.

Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.


Hide 19.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

a.
C183640

Using a screwdriver, remove the front drive shaft hole snap ring LH.