Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0061403 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Opened or Closed Using the Power Back Door Switch  


DESCRIPTION

When the power back door cannot be opened or closed using the back door control switch, one of the following may be malfunctioning: 1) back door control switch circuit, 2) multiplex network door ECU or 3) main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E270968
1.344,1.427 1.802,1.625 0.458,0.198 10 false G73 1.375,1.625 5.042,1.823 3.667,0.198 10 false Back Door Control Switch 0.781,2.354 4.448,2.552 3.667,0.198 10 false : CAN Communication Line 5.063,1.979 6.896,2.344 1.833,0.365 10 false Multiplex Network Door ECU 3.125,1.917 3.583,2.115 0.458,0.198 10 false G79 3.115,2.094 4.76,2.448 1.646,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 3.646,1.052 4.323,1.271 0.677,0.219 10 false PBDS 3.385,0.938 3.844,1.135 0.458,0.198 10 false 27 1.313,0.927 1.771,1.125 0.458,0.198 10 false 1 2.896,0.927 3.354,1.125 0.458,0.198 10 false 4 1.49,0.969 1.948,1.167 0.458,0.198 10 false MSE 2.448,0.969 2.906,1.167 0.458,0.198 10 false MSW

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.


PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Check the Data List to determine if the back door control switch functions properly.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open SW Back door control switch signal ON or OFF ON: Back door control switch pushed
OFF: Back door control switch not pushed
-
Body Electrical > Main Body > Data List
Tester Display
Back Door Open SW
50003 123 95
OK:

The back door control switch functions as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

2.REPLACE MULTIPLEX NETWORK DOOR ECU

NG

5.INSPECT BACK DOOR CONTROL SWITCH
2.REPLACE MULTIPLEX NETWORK DOOR ECU
a.

Temporarily replace the multiplex network door ECU with a new or normally functioning one.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.INITIALIZE MULTIPLEX NETWORK DOOR ECU
3.INITIALIZE MULTIPLEX NETWORK DOOR ECU
a.

Perform the initialization for the multiplex network door ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CHECK POWER BACK DOOR SYSTEM
4.CHECK POWER BACK DOOR SYSTEM
a.

Check that the power back door operates normally.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>OPERATION CHECK


Result:
Proceed to
Power back door operates normally
Power back door does not operate



Power back door operates normally

END (MULTIPLEX NETWORK DOOR ECU WAS DEFECTIVE)

Power back door does not operate

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.INSPECT BACK DOOR CONTROL SWITCH
a.

Remove the back door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the back door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BACK DOOR CONTROL SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (BACK DOOR CONTROL SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the G73 back door control switch connector.


b.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G73-4 (MSW) - G79-27 (PBDS) Always Below 1 Ω
G73-1 (MSE) - Body ground Always Below 1 Ω
G73-4 (MSW) or G79-27 (PBDS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR