The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU).
Before replacing the certification ECU (smart key ECU assembly), refer to Registration.*
*: w/ Smart Key System
Check vehicle type.
| Proceed to |
|---|
| for Navigation Receiver Type |
| for Radio Receiver Type |
| for Radio and Display Type |
for Navigation Receiver Type
for Radio Receiver Type
for Radio and Display Type
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
*1: for 11 Speakers
*2: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the M22 stereo component amplifier assembly connector.*1
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*2
Disconnect the A62 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle except 11 speakers, proceed to next step.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
*: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G143 navigation receiver assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*
Disconnect the A62 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicle without a smart key system, proceed to next step.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
*1: for Radio Receiver Type
*2: for Radio and Display Type
*3: for Navigation Receiver Type
*4: for 11 Speakers
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G143 radio and display receiver assembly*2 or navigation receiver assembly*3 connector.
Disconnect the M22 stereo component amplifier assembly connector.*4
Disconnect the A62 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
*1: for Radio Receiver Type
*2: for Radio and Display Type
*3: for Navigation Receiver Type
*4: for 11 Speakers
*5: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G143 radio and display receiver assembly*2 or navigation receiver assembly*3 connector.
Disconnect the M22 stereo component amplifier assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the A64 brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A64-11 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect an oscilloscope to terminal G16-5 (SI) and body ground.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | G16-5 (SI) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Driving at approximately 20 km/h (12 mph) |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
*: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*
Disconnect the A62 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 11 Speakers
*2: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G143 navigation receiver assembly connector.
Disconnect the M22 stereo component amplifier assembly connector.*1
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*2
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G143-17 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G143-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the M22 stereo component amplifier assembly connector.
Disconnect the G143 navigation receiver assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - M22-11 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or M22-11 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Radio and Display Type
*3: for Navigation Receiver Type
*4: for 11 Speakers
Disconnect the G16 combination meter assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G143 radio and display receiver assembly*2 or navigation receiver assembly*3 connector.
Disconnect the M22 stereo component amplifier assembly connector.*4
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G84-27 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G84-27 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio Receiver Type
*2: for Radio and Display Type
*3: for Navigation Receiver Type
*4: for 11 Speakers
*5: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the A62 ECM connector.
Disconnect the G48 radio receiver assembly connector.*1
Disconnect the G143 radio and display receiver assembly*2 or navigation receiver assembly*3 connector.
Disconnect the M22 stereo component amplifier assembly connector.*4
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - A62-57 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or A62-57 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 combination meter assembly connector.
Disconnect the A64 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-5 (SI) - A64-11 (SP1) | Always | Below 1 Ω |
| G16-5 (SI) or A64-11 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
*: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*
Disconnect the A62 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G48 radio receiver assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G48-17 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G48-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: w/ Smart Key System
Disconnect the G16 combination meter assembly connector.
Disconnect the G143 radio and display receiver assembly connector.
Disconnect the G84 certification ECU (smart key ECU assembly) connector.*
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-6 (+S) - G143-17 (SPD) | Always | Below 1 Ω |
| G16-6 (+S) or G143-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG