Home › Engine / Hybrid System › 2AD-FHV LUBRICATION › OIL PUMP
RM3090E _51 Engine / Hybrid System _008384 2AD-FHV LUBRICATION _0046776 OIL PUMP A

2AD-FHV LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A291291C01
0.76,2.438 1.073,2.594 0.313,0.156 10 *a 1.813,2.344 2.125,2.5 0.313,0.156 10 *b 1.823,2.875 2.135,3.031 0.313,0.156 10 *c
*a 34 mm (1.34 in.)
*b 25 mm (0.984 in.)
*c 9.0 mm (0.354 in.)


Using an E6 "TORX" wrench, install the 3 stud bolts.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 11301C 2.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A201761C02
0.417,1.25 1.5,1.25 true 1.167,2.833 1.5,2.833 true 1.75,2.667 2,2.333 2,2.333 2.156,2.333 true 1.958,2.917 2.083,2.583 2.083,2.583 2.24,2.583 true 2.188,2.24 2.5,2.396 0.313,0.156 10 *1 2.271,2.479 2.583,2.635 0.313,0.156 10 *2 0.125,1.146 0.583,1.344 0.458,0.198 10 SST 0.885,2.729 1.344,2.927 0.458,0.198 10 SST
*1 Front Crankshaft Oil Seal
*2 Timing Chain Cover Sub-assembly


Using SST and a hammer, tap in a new front crankshaft oil seal until its surface is flush with the timing chain cover sub-assembly edge.

SST
09223-50010  

Standard depth:

0 to 0.6 mm (0 to 0.236 in.)


NOTICE:
·

Keep the lip of the front crankshaft oil seal free from foreign matter.

·

Do not tap in the front crankshaft oil seal at an angle.




b.

Apply MP grease to the lip of the front crankshaft oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the front crankshaft oil seal.

·

Do not allow MP grease to contact the dust seal.




Hide 3.INSTALL STRAIGHT SCREW PLUG

a.

Using a 10 mm socket hexagon wrench, install a new gasket and the straight screw plug.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 11302 4.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Remove any old seal packing material.


b.

Install a new gasket and O-ring to the timing chain cover sub-assembly.


c.

Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

A291294C01
1.292,7.49 2.063,7.688 0.771,0.198 10 A - A 3.26,7.49 4.031,7.688 0.771,0.198 10 B - B 5.708,7.49 6.479,7.688 0.771,0.198 10 C - C 2.417,1.469 2.573,1.667 0.156,0.198 10 A 2.781,1.469 2.938,1.667 0.156,0.198 10 A 1.25,2.26 1.406,2.458 0.156,0.198 10 B 1.615,2.26 1.771,2.458 0.156,0.198 10 B 2.167,2.26 2.323,2.458 0.156,0.198 10 B 2.531,2.26 2.688,2.458 0.156,0.198 10 B 3.917,2.271 4.104,2.49 0.188,0.219 10 C 6.073,2.271 6.26,2.49 0.188,0.219 10 C 3.917,1.531 4.104,1.75 0.188,0.219 10 C 6.073,1.542 6.26,1.76 0.188,0.219 10 C 4.313,0.656 4.625,0.813 0.313,0.156 10 *a 3.083,2.01 3.396,2.167 0.313,0.156 10 *b 3.094,3.031 3.406,3.188 0.313,0.156 10 *c 1.375,5.438 1.688,5.594 0.313,0.156 10 *d 3.333,5.396 3.646,5.552 0.313,0.156 10 *e 6.25,6.344 6.563,6.5 0.313,0.156 10 *f 5.792,6.875 6.094,7.167 0.302,0.292 10 *g 5.313,0.646 5.625,0.802 0.313,0.156 10 *a
*a 15 mm (0.591 in.) or more *b 30 mm (1.18 in.)
*c 310.5 mm (1 ft.) *d 2.0 to 4.0 mm (0.0787 to 0.157 in.)
*e 8.0 to 10 mm (0.315 to 0.394 in.) *f 13 mm (0.512 in.)
*g 6.0 mm (0.236 in.) - -


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Apply Seal Packing as Follows:
Area Seal Packing Diameter (Round) Seal Packing Dimension (Flat) Seal Packing Application Length
A - A 2.0 to 4.0 mm (0.0787 to 0.157 in.) - -
B - B 8.0 to 10 mm (0.315 to 0.394 in.) - 30 mm (1.18 in.)
C - C - 13 mm (0.512 in.) or more wide and 6.0 mm (0.236 in.) or more thick 15 mm (0.591 in.)


NOTICE:
·

Be sure to clean and degrease the contact surfaces, especially the 4 areas indicated by the arrows in the illustration.

·

When the contact surfaces are wet, wipe them off with an oil-free cloth before applying seal packing.

·

When applying seal packing to area C - C, apply it in the direction of the white arrows in the illustration.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.




d.
A291319C01
1.854,0.802 2,0.167 2,0.167 2.167,0.167 true 2.188,0.063 2.5,0.219 0.313,0.156 10 *1 1.51,1.604 1.667,1.802 0.156,0.198 10 A 2.792,3.844 2.948,4.042 0.156,0.198 10 B 2.76,3.51 3,3.74 0.24,0.229 10 B 2.146,4.188 2.302,4.385 0.156,0.198 10 B 0.719,3.51 0.875,3.708 0.156,0.198 10 B 0.594,1.656 0.833,1.885 0.24,0.229 10 C 0.677,2.104 0.917,2.333 0.24,0.229 10 C 0.646,2.51 0.885,2.74 0.24,0.229 10 C 0.823,2.844 1.063,3.073 0.24,0.229 10 C 0.74,3.24 0.979,3.469 0.24,0.229 10 C 0.625,3.854 0.865,4.083 0.24,0.229 10 C 2.51,2.104 2.75,2.333 0.24,0.229 10 C 2.813,1.615 3.052,1.844 0.24,0.229 10 C
*1 Adhesive
V100136

Bolt and New Seal Washer


Apply adhesive to the 4 bolts labeled B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.

Temporarily install the timing chain cover sub-assembly and a new seal washer with the 13 bolts.

Bolt Length:
Item Specified Condition
Bolt A 60 mm (2.36 in.)
Bolt B 30 mm (1.18 in.)
Bolt C 30 mm (1.18 in.)


HINT:

Bolt B and C are identical.



f.

Tighten the 12 bolts labeled B and C.

Torque:
23 N*m (229 kgf*cm, 17 ft.*lbf)


g.

Tighten the bolt labeled A.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 6.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11401G 7.CONNECT CRANKSHAFT POSITION SENSOR WIRE HARNESS

a.
A201751C01
1.083,1.75 1.083,1.583 1.083,1.583 0.823,1.396 true 0.333,2.583 0.5,2.583 0.5,2.583 0.5,3 true 1.01,1.74 1.323,1.896 0.313,0.156 10 *1 0.177,2.479 0.49,2.635 0.313,0.156 10 *1
*1 Protrusion


Connect the crankshaft position sensor wire harness with the bolt and clip.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)

NOTICE:

Make sure the crankshaft position sensor wire harness is installed in the position shown in the illustration.



Hide 15104 9.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new O-ring to the oil strainer sub-assembly.


b.

Apply a light coat of engine oil to the O-ring.


c.

Install the oil strainer sub-assembly with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 15677 10.INSTALL OIL FILTER BRACKET

a.

Install a new gasket to the oil filter bracket.


b.

Install the oil filter bracket with the 4 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12102A 12.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove any old seal packing material.


b.
A291320C01
0.229,0.542 0.385,0.74 0.156,0.198 10 A 0.969,0.552 1.125,0.75 0.156,0.198 10 A 0.906,3.021 1.677,3.219 0.771,0.198 10 A - A 0.979,2.052 1.292,2.208 0.313,0.156 10 *a 1.75,2.417 2.063,2.573 0.313,0.156 10 *b
*a 12 mm (0.472 in.)
*b 4.0 to 7.0 mm (0.157 to 0.276 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Dimension:
Area Seal Packing Diameter Acceptable Seal Packing Application Range
A - A 4.0 to 7.0 mm (0.157 to 0.276 in.) 12 mm (0.472 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.




c.

Install the No. 2 oil pan sub-assembly with the 18 bolts and 2 nuts.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 11201 13.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove any old seal packing material.


b.
A201847C02
2.146,1.875 2.813,1.875 true 2.333,1.875 2.333,1.573 2.333,1.573 2.823,1.573 true 0.531,1.271 0.917,0.917 0.917,0.917 1.083,0.917 true 0.51,2.75 0.677,2 0.677,2 0.844,2 true 1.125,0.823 1.281,1.021 0.156,0.198 10 A 0.885,1.906 1.042,2.104 0.156,0.198 10 A 2.021,1.771 2.177,1.969 0.156,0.198 10 B 0.948,4.167 1.104,4.365 0.156,0.198 10 A 2.458,4.177 2.615,4.375 0.156,0.198 10 B 0.427,0.385 0.74,0.542 0.313,0.156 10 *a 2.74,0.417 3.052,0.573 0.313,0.156 10 *b 0.896,3.344 1.208,3.5 0.313,0.156 10 *c 2.417,3.177 2.729,3.333 0.313,0.156 10 *c
*a 8.0 mm (0.315 in.)
*b 10 mm (0.394 in.)
*c 6.0 mm (0.236 in.)


Apply seal packing to the cylinder head sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Dimension:
Area Seal Packing Diameter Seal Packing Application Length
A 6.0 mm (0.236 in.) 8.0 mm (0.315 in.)
B 6.0 mm (0.236 in.) 10 mm (0.394 in.)



c.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

i.

Install the cylinder head cover gasket so that the triangle tabs of the cylinder head cover gasket are aligned with the protrusions of the cylinder head cover sub-assembly as shown in the parts of the illustration labeled A and B.


ii.

Install the cylinder head cover gasket to the groove of the cylinder head cover moving from C and D in the direction of the black arrows shown in the illustration.


iii.

Install the cylinder head cover gasket to the groove of the cylinder head cover moving from C and D towards E as shown by the white arrows in the illustration.


iv.

Install the cylinder head gasket to the groove of the cylinder head cover moving from D towards F as shown by the striped arrow in the illustration.


v.

Install the cylinder head cover gasket to the cylinder head cover sub-assembly pins and cutouts as shown in the parts of the illustration labeled G and H.

A291299C01
5.177,1.042 5.177,0.573 true 5.677,1.031 5.677,0.698 true 2.625,3.49 2.625,3.146 true 2.125,3.49 2.125,3.01 true 0.75,2.313 0.75,2.146 true 0.5,2.302 0.5,2.188 0.5,2.188 0.708,2.063 true 2.229,1.094 2.229,0.833 true 2.573,1.073 2.573,0.958 2.573,0.958 2.302,0.885 true 2.156,1.083 2.469,1.24 0.313,0.156 10 *1 2.49,1.073 2.802,1.229 0.313,0.156 10 *2 5.615,1.031 5.927,1.188 0.313,0.156 10 *3 5.104,1.031 5.417,1.188 0.313,0.156 10 *4 1.51,0.198 1.667,0.396 0.156,0.198 10 A 5.896,2.854 6.052,3.052 0.156,0.198 10 D 0.427,1.448 0.583,1.646 0.156,0.198 10 B 3.021,1.167 3.177,1.365 0.156,0.198 10 E 5.323,3.219 5.573,3.448 0.25,0.229 10 C 3.167,1.698 3.323,1.896 0.156,0.198 10 F 4.896,0.208 5.052,0.406 0.156,0.198 10 G 1.865,2.646 2.021,2.844 0.156,0.198 10 H 2.052,3.49 2.365,3.646 0.313,0.156 10 *4 2.552,3.49 2.865,3.646 0.313,0.156 10 *3 0.417,2.302 0.729,2.458 0.313,0.156 10 *1 0.677,2.313 0.99,2.469 0.313,0.156 10 *2
*1 Triangle Tab of Cylinder Head Cover Gasket *2 Protrusion of Cylinder Head Cover Sub-assembly
*3 Cylinder Head Cover Sub-assembly Pin *4 Cutout of Cylinder Head Cover Sub-assembly


NOTICE:
A263853C02
0.677,1.927 0.99,2.083 0.313,0.156 10 *a 2.333,1.938 2.646,2.094 0.313,0.156 10 *b
*a CORRECT
*b INCORRECT
V100155

Rib of Cylinder Head Cover Gasket


Make sure that the rib of the cylinder head cover gasket is securely inserted into the groove of the cylinder head cover sub-assembly.




d.
A291300C01
2.688,1.313 3,1.51 0.313,0.198 10 17 2.542,0.927 2.854,1.125 0.313,0.198 10 16 2.156,0.021 2.469,0.219 0.313,0.198 10 15 1.625,0.042 1.938,0.24 0.313,0.198 10 14 1,0.01 1.313,0.208 0.313,0.198 10 13 0.552,0.844 0.865,1.042 0.313,0.198 10 12 0.5,1.292 0.813,1.49 0.313,0.198 10 11 0.677,1.823 0.99,2.021 0.313,0.198 10 10 0.75,2.333 1.063,2.531 0.313,0.198 10 9 2.563,2.948 2.875,3.146 0.313,0.198 10 6 0.802,2.979 1.115,3.177 0.313,0.198 10 8 2.552,2.344 2.865,2.542 0.313,0.198 10 5 1.771,3.177 2.083,3.375 0.313,0.198 10 7 2.552,1.833 2.865,2.031 0.313,0.198 10 4 2.531,1.313 2.844,1.51 0.313,0.198 10 3 0.75,1.292 1.063,1.49 0.313,0.198 10 2 1.719,1.021 2.031,1.219 0.313,0.198 10 1
V100136

Nut


Install the cylinder head cover sub-assembly with the 14 bolts and nut, and tighten the bolts and nut in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Partially tighten the bolt indicated by the number 6 in the illustration until the cylinder head cover sub-assembly contacts the cylinder head sub-assembly, and then tighten the bolts and nut in the order shown in the illustration.



Hide 23699A 14.INSTALL NOZZLE HOLDER CLAMP SEAT

a.
A263982

Install the 4 nozzle holder clamp seats.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108 15.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 12261 16.INSTALL PCV HOSE

a.
A291458C01
0.917,2.833 1.083,2.833 1.083,2.833 1.625,3.115 true 0.771,2.75 1.083,2.906 0.313,0.156 10 false *1 1.552,2.729 1.865,2.885 0.313,0.156 10 false *a 0.969,3.25 1.281,3.406 0.313,0.156 10 false *b 2.333,2.969 2.792,3.167 0.458,0.198 10 false 45° 2.333,3.563 2.792,3.76 0.458,0.198 10 false 45°
*1 Paint Mark
*a Upper Side
*b Front Side of Vehicle


Install the PCV hose to the cylinder head cover sub-assembly, and slide the clamp to secure the hose.

HINT:

The direction of the hose clamp is indicated in the illustration.



Hide 25760A 17.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY

a.
A291321C01
0.615,2.031 0.927,2.188 0.313,0.156 10 *a 0.542,4.354 0.854,4.51 0.313,0.156 10 *b 1.573,4.344 1.885,4.5 0.313,0.156 10 *b 1.74,2.76 2.052,2.917 0.313,0.156 10 *b 0.604,2.76 0.917,2.917 0.313,0.156 10 *b 1.74,2.031 2.052,2.188 0.313,0.156 10 *a 2.802,2.031 3.115,2.188 0.313,0.156 10 *a 2.615,3.677 2.927,3.833 0.313,0.156 10 *a 1.594,3.677 1.906,3.833 0.313,0.156 10 *a 0.542,3.677 0.854,3.833 0.313,0.156 10 *a 0.406,0.521 0.667,0.75 0.26,0.229 10 A 3.021,0.76 3.281,0.99 0.26,0.229 10 A 1.677,0.75 1.938,0.979 0.26,0.229 10 A 2.208,0.458 2.469,0.688 0.26,0.229 10 A 1.49,0.167 1.75,0.396 0.26,0.229 10 B 0.219,1.292 0.479,1.521 0.26,0.229 10 A 0.219,2.99 0.479,3.219 0.26,0.229 10 B
*a CORRECT
*b INCORRECT
V100145

Paint Mark


Attach the 10 clamps to install the 2 vacuum transmitting hoses.

HINT:
·

Make sure that the paint marks of the vacuum transmitting hoses at the locations labeled A in the illustration are aligned as shown in the illustration. Any of the "CORRECT" alignments are acceptable for each location.

·

Make sure that the paint marks of the vacuum transmitting hoses at the locations labeled B in the illustration are aligned as shown in the illustration. Any of the "CORRECT" alignments are acceptable for each location.




Hide 25819 18.INSTALL VACUUM REGULATING VALVE ASSEMBLY

Hide 25860 19.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

Hide 23762 21.INSTALL NO. 2 NOZZLE LEAKAGE PIPE

a.

Temporarily install the No. 2 nozzle leakage pipe and a new gasket with the check valve and bolt.


b.

Tighten the check valve.

Torque:
32 N*m (321 kgf*cm, 23 ft.*lbf)


c.

Tighten the bolt.

Torque:
32 N*m (321 kgf*cm, 23 ft.*lbf)


Hide 23274D 22.INSTALL NO. 3 FUEL HOSE

a.

Install the No. 3 fuel hose to the fuel supply pump assembly and No. 2 nozzle leakage pipe, and slide the 2 clamps to secure the hose.


Hide 23901E 23.INSTALL FUEL TUBE SUB-ASSEMBLY

Hide 16323 25.INSTALL WATER INLET HOUSING

a.

Install a new gasket and the water inlet housing with the 3 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 16281 26.INSTALL NO. 4 WATER BY-PASS HOSE

a.

Install the No. 4 water by-pass hose to the water inlet housing and elbow, and slide the 2 clamps to secure the hose.


Hide 16278 27.INSTALL NO. 2 WATER BY-PASS PIPE

a.

Install a new O-ring to the No. 2 water by-pass pipe.


b.

Install the No. 2 water by-pass pipe with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 15781 28.INSTALL NO. 1 OIL COOLER BRACKET

a.
A123533E02
0.521,0.365 0.677,0.563 0.156,0.198 10 A 0.521,1.052 0.677,1.25 0.156,0.198 10 B 0.49,1.646 0.646,1.844 0.156,0.198 10 B

Apply engine oil to the 2 new O-rings labeled B in the illustration.

NOTICE:

Do not apply engine oil to the new O-ring labeled A in the illustration.



b.

Install the 3 new O-rings to the No. 1 oil cooler bracket.


c.

Install the No. 1 oil cooler bracket with the 6 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15481 29.INSTALL NO. 1 TURBO OIL PIPE

a.
A291302C01
1.417,2.25 1.583,2.25 1.583,2.25 1.792,2.667 true 1.26,2.146 1.573,2.302 0.313,0.156 10 *1 0.479,1.49 0.635,1.688 0.156,0.198 10 A
*1 Gasket


Install the No. 1 turbo oil pipe and 2 new gaskets with the 2 union bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Make sure the gasket of union bolt A contacts the No. 1 turbo oil pipe as shown in the illustration when tightening the union bolt.



Hide 16279 30.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Install a new O-ring to the No. 3 water by-pass pipe.


b.

Install the No. 3 water by-pass pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16296 31.INSTALL NO. 8 WATER BY-PASS HOSE

a.

Install the No. 8 water by-pass hose to the No. 3 water by-pass pipe, and slide the clamp to secure the hose.


Hide 16283 32.INSTALL NO. 6 WATER BY-PASS HOSE

a.

Install the No. 6 water by-pass hose to the water outlet, and slide the clamp to secure the hose.


Hide 15710 33.INSTALL OIL COOLER ASSEMBLY

Hide 12581A 35.INSTALL NO. 1 CYLINDER BLOCK INSULATOR

a.
A201839

Install the No. 1 cylinder block insulator to the cylinder block sub-assembly.

NOTICE:

Be sure to install the oil cooler assembly before installing the No. 1 cylinder block insulator.



Hide 17112 37.INSTALL NO. 2 INTAKE MANIFOLD

Hide 12631A 38.INSTALL ENGINE COVER BRACKET

Hide 17853B 42.INSTALL INTAKE MANIFOLD INSULATOR

Hide 23810A 43.INSTALL COMMON RAIL ASSEMBLY

a.

Install the common rail assembly with the 2 bolts.

Torque:
21 N*m (209 kgf*cm, 15 ft.*lbf)


Hide 23282D 44.INSTALL NO. 4 FUEL HOSE

a.

Install the No. 4 fuel hose to the common rail assembly and No. 2 nozzle leakage pipe, and slide the 2 clamps to secure the hose.


Hide 23701 45.INSTALL INJECTION PIPE SUB-ASSEMBLY

Hide 23804C 46.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 11452 47.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the engine oil level dipstick guide.


b.

Install the engine oil level dipstick guide with the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.

Install the engine oil level dipstick.


Hide 25800 48.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 25602 49.INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY

Hide 25625 50.INSTALL EGR VALVE BRACKET

a.

Install the EGR valve bracket with the 3 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 16296 51.CONNECT NO. 8 WATER BY-PASS HOSE

Hide 16295 52.INSTALL NO. 7 WATER BY-PASS HOSE

Hide 26100 53.INSTALL DIESEL THROTTLE BODY ASSEMBLY

a.

Install a new gasket and the diesel throttle body assembly with the 2 bolts and 2 nuts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


b.

Connect the No. 6 water by-pass hose and No. 7 water by-pass hose to the diesel throttle body assembly, and slide the 2 clamps to secure the hoses.


Hide 16620 54.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

As the heads of the bolts are not as thick as those of typical bolts, be careful not to damage them during installation.



Hide 12315A 55.INSTALL ENGINE MOUNTING BRACKET

a.

Temporarily install the engine mounting bracket with the 2 bolts labeled A.


b.
A291303N01
1.781,0.281 1.938,0.479 0.156,0.198 10 A 0.49,1.104 0.646,1.302 0.156,0.198 10 A 2.177,0.583 2.333,0.781 0.156,0.198 10 B 2.865,0.833 3.021,1.031 0.156,0.198 10 B 2.448,1.49 2.604,1.688 0.156,0.198 10 B 1.854,1.813 2.01,2.01 0.156,0.198 10 B

Temporarily install the 2 bolts and 2 nuts labeled B in the illustration.


c.

Tighten the 2 bolts labeled A in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


d.

Tighten the 2 bolts and 2 nuts labeled B in the illustration.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 16288 56.INSTALL NO. 4 WATER BY-PASS PIPE

a.

Install a new O-ring to the No. 4 water by-pass pipe.


b.

Install the No. 4 water by-pass pipe with the bolt.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 16604 57.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.
A201747C04
1.417,1.333 2.26,1.333 true 1.167,0.25 1.333,0.25 1.333,0.25 1.667,0.552 true 1.021,0.146 1.333,0.302 0.313,0.156 10 *1 1.26,1.229 1.573,1.385 0.313,0.156 10 *2
*1 No. 2 Idler Pulley Cover Plate
*2 No. 2 Idler Pulley Sub-assembly


Install the No. 2 idler pulley sub-assembly and No. 2 idler pulley cover plate with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:

Make sure the No. 2 idler pulley cover plate is facing the direction shown in the illustration.



Hide 16603 58.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley sub-assembly with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 16649B 59.INSTALL IDLER PULLEY COVER PLATE

a.

Install the idler pulley cover plate to the No. 1 idler pulley sub-assembly.


Hide 29300 60.INSTALL VACUUM PUMP ASSEMBLY

a.

Apply a light coat of engine oil to 2 new O-rings.


b.

Install the 2 O-rings to the vacuum pump assembly.


c.

Install the vacuum pump assembly with 3 new bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the vacuum hose.


Hide 27020 61.INSTALL GENERATOR ASSEMBLY

Hide 62.CONNECT ENGINE WIRE

a.

Connect the connectors and attach the clamps, and then connect the engine wire to the engine with the bracket bolts.