Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT › 2012.12–2015.04
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046816 ENGINE UNIT A

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 12551A 1.INSTALL NO. 1 VACUUM PUMP BRACKET

a.

Install a new gasket and the No. 1 vacuum pump bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 29300 2.INSTALL VACUUM PUMP ASSEMBLY

Hide 44774 3.CONNECT UNION TO CONNECTOR TUBE HOSE

Hide 16268 7.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install the No. 1 water by-pass pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16262 8.INSTALL WATER INLET HOSE

a.

Install the water inlet hose, and slide the 2 clamps to secure the hose.


Hide 16261 9.INSTALL WATER BY-PASS HOSE

a.

Install the water by-pass hose, and slide the clamp to secure the hose.


Hide 16267 10.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the water inlet housing, and slide the clamp to secure the hose.


Hide 12261 11.INSTALL PCV HOSE

a.

Install the PCV hose to the PCV valve and slide the clamp to secure it.


Hide 16279 12.INSTALL NO. 3 WATER BY-PASS PIPE (for CVT)

a.

Install a new gasket and the No. 3 water by-pass pipe with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11492D 13.INSTALL NO. 1 SEAL PLATE (for Manual Transaxle)

a.

Install the No. 1 seal plate and new gasket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17167 16.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 17.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250 18.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807V 19.INSTALL NO. 1 DELIVERY PIPE SPACER

Hide 23807 20.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23901 21.INSTALL FUEL TUBE SUB-ASSEMBLY

Hide 22.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 87245A 24.INSTALL HEATER WATER INLET HOSE

a.

Connect the heater water inlet hose to the cylinder head sub-assembly, and slide the clamp to secure the hose.


Hide 87246A 25.INSTALL HEATER WATER OUTLET HOSE

a.

Connect the heater water outlet hose to the No. 1 water by-pass pipe, and slide the clamp to secure the hose.


Hide 22210 27.INSTALL THROTTLE BODY ASSEMBLY

Hide 28.INSTALL ENGINE WIRE