Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2012.12–2015.10
RM3090E _55 Steering _008772 POWER ASSIST SYSTEMS _0049011 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1581/26  Assist Map Number Un-Writing  


DESCRIPTION

This DTC will be stored if the power steering ECU assembly determines that the assist map is not written in the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1581/26 Assist Map Number Un-Writing Assist map not written in power steering ECU assembly
·

CAN communication system

·

SFI system

·

Brake control system

·

Main body ECU (multiplex network body ECU)

·

Power steering ECU assembly


On Assist map written

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.PERFORM ASSIST MAP WRITING
a.

Perform the assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

Chassis > EMPS > Utility
Tester Display
Signal Check
50005 142 3

b.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
Result:
Proceed to
DTC C1581/26 is output.
DTC C1581/26 is not output.


NOTICE:

DTC C1581/26 is cleared after the assist map is written.




DTC C1581/26 is output.

2.CHECK CAN COMMUNICATION SYSTEM

DTC C1581/26 is not output.

END

2.CHECK CAN COMMUNICATION SYSTEM
a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
Result:
Proceed to
DTCs is not output
DTCs is output




DTCs is not output

3.CHECK RELATED PART (ECM, MAIN BODY ECU AND SKID CONTROL ECU)

DTCs is output

3.CHECK RELATED PART (ECM, MAIN BODY ECU AND SKID CONTROL ECU)
a.

Check if any of the parts listed below have been replaced with an incorrect part in the past.

Related Part ECM
Main body ECU (multiplex network body ECU)
Skid control ECU (brake actuator assembly)

NOTICE:

When removing a related part to check it, be sure to follow the appropriate procedures and precautions.

·

Refer to the following procedures to remove the ECM (for 1AD-FTV).

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL

·

Refer to the following procedures to remove the ECM (for 2AD-FHV).

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL

·

Refer to the following procedures to remove the ECM (for 2AD-FTV).

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL

·

Refer to the following procedures to remove the ECM (for 2AR-FE).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL

·

Refer to the following procedures to remove the ECM (for 3ZR-FAE).

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL

·

Refer to the following procedures to remove the ECM (for 3ZR-FE).

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL

·

Refer to the following procedures to remove the main body ECU (multiplex network body ECU) (for LHD).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

·

Refer to the following procedures to remove the main body ECU (multiplex network body ECU) (for RHD).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL

·

Refer to the following procedures to remove the skid control ECU (brake actuator assembly) (w/ VSC).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL

·

Refer to the following procedures to remove the skid control ECU (brake actuator assembly) (w/o VSC).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL



HINT:
·

DTC C1581/26 is stored when a part with an incorrect part number is installed for the related parts listed above.

·

When DTC C1581/26 is output when parts have not been exchanged, replace the power steering ECU assembly as it may have an internal malfunction.



Result:
Proceed to
All installed related parts have correct part number
Part with incorrect part number is installed




All installed related parts have correct part number

REPLACE POWER STEERING ECU ASSEMBLY

Part with incorrect part number is installed

REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER