Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.

·

When the battery of the electrical key transmitter sub-assembly is depleted, the brake pedal*1 or clutch pedal*2 is depressed and the electrical key transmitter sub-assembly is held near the engine switch.

·

When the entry cancel function has been canceled through the customized parameters, the brake pedal*1 or clutch pedal*2 is depressed and the electrical key transmitter sub-assembly is held near the engine switch.

*1: except Manual Transaxle

*2: for Manual Transaxle



HINT:
·

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

·

If the room oscillator does not recognize the key, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.



Radio Wave Interference:
Problem Symptom Data List Item
Operating Engine Switch / Key RF Signal Interference When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control:
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-

WIRING DIAGRAM

C278824E01
0.24,0.365 1.198,0.594 0.958,0.229 10 false from Battery 1.615,0.563 2.063,0.74 0.448,0.177 10 false AM2 0.656,3.344 1.667,3.552 1.01,0.208 10 false Engine Switch 0.656,3.177 1.667,3.385 1.01,0.208 10 false G24 1.031,5.063 1.49,5.24 0.458,0.177 10 false IG2 1.479,4.208 1.938,4.385 0.458,0.177 10 false 5 1.49,4.625 1.948,4.802 0.458,0.177 10 false 1 0.698,4.208 1.156,4.385 0.458,0.177 10 false 3 0.688,4.604 1.146,4.781 0.458,0.177 10 false 2 2.469,4.552 2.927,4.729 0.458,0.177 10 false 9 2.375,4.74 2.833,4.917 0.458,0.177 10 false G82 2.396,1.99 2.854,2.167 0.458,0.177 10 false G84 2.385,2.438 2.844,2.615 0.458,0.177 10 false G84 2.396,2.885 2.854,3.063 0.458,0.177 10 false G84 2.385,0.969 2.844,1.146 0.458,0.177 10 false G82 3.583,6.781 4.042,6.958 0.458,0.177 10 false G82 3.635,6.594 4.094,6.771 0.458,0.177 10 false 18 4.5,6.688 4.958,6.865 0.458,0.177 10 false 1 5.646,6.667 6.104,6.844 0.458,0.177 10 false 2 4.531,7.115 4.99,7.292 0.458,0.177 10 false A5 4.531,7.281 6.427,7.49 1.896,0.208 10 false Stop Light Switch Assembly*4 6.177,7.948 6.635,8.125 0.458,0.177 10 false STOP 4.938,7.781 5.844,7.99 0.906,0.208 10 false from Battery 2.75,4.74 3.208,4.917 0.458,0.177 10 false IG2D 1.104,2.875 1.594,3.042 0.49,0.167 10 false AGND 1.208,2.427 1.615,2.594 0.406,0.167 10 false SS2 1.219,2 1.615,2.167 0.396,0.167 10 false SS1 2.448,2.688 2.667,2.865 0.219,0.177 10 false 24 2.438,2.25 2.656,2.427 0.219,0.177 10 false 30 2.417,0.781 2.635,0.958 0.219,0.177 10 false 11 2.729,2.896 3.188,3.073 0.458,0.177 10 false AGND 2.719,2.448 3.177,2.625 0.458,0.177 10 false SSW2 2.719,2 3.177,2.177 0.458,0.177 10 false SSW1 3.188,2.969 3.646,3.146 0.458,0.177 10 false IG1D 3.604,2.969 4.063,3.146 0.458,0.177 10 false G84 3.115,1.708 3.573,1.885 0.458,0.177 10 false ACCD 3.583,1.698 4.042,1.875 0.458,0.177 10 false G84 4.208,1.281 4.667,1.458 0.458,0.177 10 false 3A 4.208,1.698 4.667,1.875 0.458,0.177 10 false 3C 4.219,2.969 4.677,3.146 0.458,0.177 10 false 3C 6.573,2.552 7.031,2.729 0.458,0.177 10 false 3C 6.573,3.74 7.031,3.917 0.458,0.177 10 false 3C 6.583,4.917 7.042,5.094 0.458,0.177 10 false 3C 6.583,1.281 7.042,1.458 0.458,0.177 10 false 3D 2.427,1.802 2.646,1.979 0.219,0.177 10 false 28 2.385,0.375 2.844,0.552 0.458,0.177 10 false G82 2.49,0.167 2.708,0.344 0.219,0.177 10 false 2 2.729,0.958 3.188,1.135 0.458,0.177 10 false E 2.719,0.375 3.177,0.552 0.458,0.177 10 false +B 6.573,5.323 7.031,5.5 0.458,0.177 10 false 3D 3.01,6.771 3.615,7 0.604,0.229 10 false STP1*4 5.073,5.656 5.917,5.833 0.844,0.177 10 false IG1 NO. 3 5,4.469 5.844,4.646 0.844,0.177 10 false IG1 NO. 2 5,3.281 5.844,3.458 0.844,0.177 10 false IG1 NO. 1 5.188,2.01 5.844,2.198 0.656,0.188 10 false ACC 6.083,1.469 6.74,1.656 0.656,0.188 10 false ACC 6.073,2.708 6.635,3.104 0.563,0.396 10 false ECU-IG NO. 1 6.083,3.906 6.74,4.094 0.656,0.188 10 false WIP FR 6.042,5.052 6.469,5.427 0.427,0.375 10 false S-HTR RH 6.604,5.167 6.927,5.344 0.323,0.177 10 false 9 6.615,4.719 6.938,4.896 0.323,0.177 10 false 3 6.615,3.531 6.938,3.708 0.323,0.177 10 false 1 6.604,2.365 6.927,2.542 0.323,0.177 10 false 27 6.604,1.073 6.927,1.25 0.323,0.177 10 false 51 4.24,1.51 4.563,1.688 0.323,0.177 10 false 45 4.24,2.771 4.563,2.948 0.323,0.177 10 false 43 3.688,2.771 4.01,2.948 0.323,0.177 10 false 6 3.698,1.49 4.021,1.667 0.323,0.177 10 false 4 4.271,1.083 4.594,1.26 0.323,0.177 10 false 1 1.688,2.771 2.01,2.948 0.323,0.177 10 false 6 1.667,2.26 1.99,2.438 0.323,0.177 10 false 1 1.656,1.896 1.979,2.073 0.323,0.177 10 false 5 2.385,6.563 2.844,6.76 0.458,0.198 10 false G82 2.729,6.573 3.344,6.771 0.615,0.198 10 false STAR 2.458,6.365 2.615,6.563 0.156,0.198 10 false 5 2.146,6.438 2.302,6.635 0.156,0.198 10 false 2 1.25,6.427 1.406,6.625 0.156,0.198 10 false 1 0.26,6.417 0.417,6.615 0.156,0.198 10 false 1 1.021,6.427 1.177,6.625 0.156,0.198 10 false 2 1.021,5.99 1.177,6.188 0.156,0.198 10 false 3 0.24,5.99 0.396,6.188 0.156,0.198 10 false 5 0.615,6.896 0.927,7.094 0.313,0.198 10 false ST 1.375,6.833 1.99,7.031 0.615,0.198 10 false A4*1 1.385,7.01 2,7.208 0.615,0.198 10 false F2*2 1.375,7.177 2.604,7.531 1.229,0.354 10 false Clutch Start Switch Assembly*3 2.521,8.24 4.042,8.594 1.521,0.354 10 false Certification ECU (Smart Key ECU Assembly) 0.177,7.76 0.813,7.979 0.635,0.219 10 false *1: LHD 0.188,8.01 0.813,8.219 0.625,0.208 10 false *2: RHD 4.167,6.104 6.844,6.313 2.677,0.208 10 false Instrument Panel Junction Block Assembly 0.188,8.26 1.781,8.438 1.594,0.177 10 false *3: for Manual Transaxle 0.198,8.5 1.958,8.677 1.76,0.177 10 false *4: except Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly or ID code box (immobiliser code ECU) (w/ Multi-information Display (Dot Display Type)), refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

OK:

Wireless door lock function operates



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO OTHER FLOWCHART (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C36
0.427,1.219 0.865,1.458 0.438,0.24 0.896,1.771 1.271,1.344 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 0.521,1.24 0.948,1.406 0.427,0.167 10 G82 0.688,1.813 1.073,1.958 0.385,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE)

3.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C40
0.521,1.323 0.958,1.563 0.438,0.24 2.063,1.583 2.448,1.792 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 2.521,1.74 2.906,1.885 0.385,0.146 10 E 0.604,1.365 1.302,1.521 0.698,0.156 10 G82
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE SWITCH FUNCTION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE SWITCH FUNCTION
a.

Remove the battery from the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT


b.
B323969

With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter near the engine switch and check if the power source mode changes.

·

*1: except Manual Transaxle

·

*2: for Manual Transaxle


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


OK:

The power source mode changes.


Result:
Proceed to
The power source mode does not change
The power source mode changes




The power source mode does not change

5.READ VALUE USING GTS (STOP LIGHT SWITCH 1, NEUTRAL SW/CLUTCH SW)

The power source mode changes

15.READ VALUE USING GTS (START SWITCH 1, 2)
5.READ VALUE USING GTS (STOP LIGHT SWITCH 1, NEUTRAL SW/CLUTCH SW)
a.

except Manual Transaxle:

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen according to the stop light switch condition.




b.

for Manual Transaxle:

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to determine whether the clutch switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
OK:

ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the stop light switch condition.


Result:
Proceed to
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)





OK

6.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG (except Manual Transaxle)

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG (for Manual Transaxle)

11.INSPECT CLUTCH START SWITCH ASSEMBLY
6.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the GTS.


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON ALL OFF: Engine switch off
ACC ON: Engine switch on (ACC) (ACC relay on)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
b.

With the engine switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch for 2 seconds or more and read the Data List.

HINT:

If the entry key function has been canceled on the customization menu, ACC ON is displayed in the Data List.


OK:

IG2 ON is displayed in the Data List.



Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

8.CHECK FOR DTC
7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

B264896C39
4.646,0.844 5.104,1.083 0.458,0.24 1.979,0.823 2.438,1.063 0.458,0.24 2.229,2.375 1.979,1.74 false 4.094,2.292 4.354,1.635 false 4.823,2.365 4.542,1.635 false 0.25,0.344 0.563,0.5 0.313,0.156 10 *a 2.063,2.396 2.49,2.573 0.427,0.177 10 IG2D 4.74,0.875 5.167,1.052 0.427,0.177 10 G84 3.938,2.333 4.365,2.51 0.427,0.177 10 IG1D 4.656,2.417 5.219,2.604 0.563,0.188 10 ACCD 2.073,0.854 2.5,1.031 0.427,0.177 10 G82
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition
G84-6 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC)
Engine switch on (IG) 9 V or higher
G82-9 (IG2D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC)
Engine switch on (IG) 9 V or higher
G84-4 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (IG) 8.5 V or higher
Engine switch on (ACC)



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK FOR DTC
a.

Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Result:
Result Proceed to
The following DTCs are not output:
·

B2784

·

B287A


A
DTC B2784 is output. B
DTC B278A is output. C




A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A5 connector from the stop light switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-18 (STP1) - A5-1 Always Below 1 Ω
G82-18 (STP1) or A5-1- Body ground 10 kΩ or higher



c.
B268627C11
1.385,0.25 1.823,0.5 0.438,0.25 1.042,1.635 1.229,1.208 false 0.302,0.125 0.615,0.281 0.313,0.156 10 *a 1.458,0.302 1.958,0.469 0.5,0.167 10 G82 0.906,1.667 1.406,1.833 0.5,0.167 10 STP1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the A5 connector from the stop light switch assembly.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-18 (STP1) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Disconnect the A5 connector from the stop light switch assembly.


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

11.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

12.INSPECT ST RELAY (STARTER RELAY ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

12.INSPECT ST RELAY (STARTER RELAY ASSEMBLY)

OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE ST RELAY (STARTER RELAY ASSEMBLY)

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A4 or F2 clutch start switch connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G82-5 (STAR) - F2-2 Always Below 1 Ω
G82-5 (STAR) or F2-2 - Body ground Always 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2 Always Below 1 Ω
G82-5 (STAR) or A4-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY (STARTER RELAY ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY (STARTER RELAY ASSEMBLY))
a.

Disconnect the A4 or F2 clutch start switch assembly connector.


b.

Remove the ST relay (starter relay assembly) from the No. 2 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A4-1 - 2 Always Below 1 Ω
1 - Body ground Below 1 Ω
A4-1 or 2 - Body ground 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
F2-1 - 2 Always Below 1 Ω
1 - Body ground Below 1 Ω
F2-1 or 2 - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ VALUE USING GTS (START SWITCH 1, 2)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.



Result:
Proceed to
OK
NG



OK

NG

16.INSPECT ENGINE SWITCH
16.INSPECT ENGINE SWITCH

Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

NG (for 1AD-FTV)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the G84 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the G24 connector from the engine switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-28 (SSW1) - G24-5 (SS1) Always Below 1 Ω
G84-30 (SSW2) - G24-1 (SS2)
G84-28 (SSW1) or G24-5 (SS1) - Body ground 10 kΩ or higher
G84-30 (SSW2) or G24-1 (SS2) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR